* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Unit 4 Assignment
Electrical ballast wikipedia , lookup
Electrification wikipedia , lookup
Electric power system wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Audio power wikipedia , lookup
Brushed DC electric motor wikipedia , lookup
Power inverter wikipedia , lookup
Electrical substation wikipedia , lookup
Pulse-width modulation wikipedia , lookup
Immunity-aware programming wikipedia , lookup
Stepper motor wikipedia , lookup
Power engineering wikipedia , lookup
Power MOSFET wikipedia , lookup
History of electric power transmission wikipedia , lookup
Voltage regulator wikipedia , lookup
Distribution management system wikipedia , lookup
Surge protector wikipedia , lookup
Opto-isolator wikipedia , lookup
Buck converter wikipedia , lookup
Stray voltage wikipedia , lookup
Power electronics wikipedia , lookup
Variable-frequency drive wikipedia , lookup
Three-phase electric power wikipedia , lookup
Alternating current wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Voltage optimisation wikipedia , lookup
E. (Mech., Mech. Sandwich & Auto) Examination, May 2014 Electronics and Electrical Engineering (203152) (2012 Pattern) Marking Scheme and Model Answers Q.1. (a) Explain following instructions of 8051 microcontroller quoting suitable examples. (i) ORL A, #data (ii) RRC A (iii) RET [6] Solution: [6] Explain the sphere gap method used for measurement of peak value of voltage. Q1. (a) Solution: Sphere Gap used for measurement of peak value of voltage Sphere Gap: This is one of the oldest technique adopted for the measurement of all the types (dc =, ac ~ and impulse) high voltages of either polarity. It remained the most widely used method for decades. The field between two identical spheres is a classical example of "weakly nonuniform” field. The breakdown characteristic of such a gap is linear for the gap distances not greater than the radius of the spheres. Measurement voltage is made as a function of minimum distance at which it can flash over or sparkover. The breakdown voltage of the gap does not depend upon the duration of application of voltage and also not upon its variation with time. (1 mark) Construction of the Sphere Gap: A sphere gap consists of two adjacent metal spheres of equal diameters whose separation gap distance is variable. The ability to respond to peak values of impulse voltages, if the time to peak is not too short ( 1-3 µsec), is governed by a short statistical time lag or the delay in time required for the availability of an electron to initiate an electron avalanche and hence the breakdown. • Within the limited gap distance between the spheres, a weakly nonuniform field exists, hence no PB or corona appears before the complete breakdown or flashover. • For a given dimension of the diameter/radius of the spheres and a gap distance between [7] them, the magnitude of the voltage at which the breakdown occured is read from the standard calibrated tables available for different types of voltages and for both their polarities. • The inaccuracy of measurement of voltage by this method is about 3%. Disadvantages: • For the measurement, breakdown in the gap has to take place. • Continuous measurement of the voltage is not possible. • This method is not very accurate. (3marks) Fig. Vertical Sphere Gap: 1. Insulating support. 2. Sphere shank. 3. Opening gear, showing maximum dimensions. 4. High-voltage connection with series resistor. 5. Stress distributor, showing maximum dimensions. P. Sparking point of .v. sphere. A. Height of P above ground plane. B. Radius of space free from external structures. X. Item 4 not to pass through this plane within a distance B from P. (Diagram: 3 marks) Two-wattmeter method is used for measurement of input power of a three phase induction motor. If two wattmeter readings are 1700 watts and 1100 watts; determine i) input power to motor ii) power factor of the motor iii) input current drawn from 440 V, 3 phase AC supply. input power to motor=2800W (2 marks) Solution: Q.7. (b) power factor of the motor=0.9375lag (2 marks) [6] input current drawn from 440 V, 3 phase AC supply=3.9189 A (2 marks) What is Wien’s Bridge? Derive expression for frequency of Wien’s Bridge. Q.8. (a) Solution: Wien’s Bridge Diagram: (3 marks) [7] Wien Bridge has a series RC combination in one and a parallel combination in the adjoining arm. Its basic form is designed to measure frequency. (1 mark) The bridge balance equation is: Z1Z4= Z2Z3 ( 3 marks) Explain one wattmeter method used for measuring reactive power of a three phase balanced load Q.8. (b) with the help of connection diagram and phasor diagram. Connection diagram (2 marks) Solution: One wattmeter method: Phasor diagram (2 marks) Reactive power measurement (2 marks) [6]