* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Agricultural Buildings (AT 3084) Basic Electrical Theory
Current source wikipedia , lookup
Brushed DC electric motor wikipedia , lookup
Audio power wikipedia , lookup
Power inverter wikipedia , lookup
Power factor wikipedia , lookup
War of the currents wikipedia , lookup
Electrical ballast wikipedia , lookup
Electric machine wikipedia , lookup
Opto-isolator wikipedia , lookup
Wireless power transfer wikipedia , lookup
History of electromagnetic theory wikipedia , lookup
Stepper motor wikipedia , lookup
Ground (electricity) wikipedia , lookup
Electric power system wikipedia , lookup
Buck converter wikipedia , lookup
Induction motor wikipedia , lookup
Power electronics wikipedia , lookup
Variable-frequency drive wikipedia , lookup
Single-wire earth return wikipedia , lookup
Circuit breaker wikipedia , lookup
Distribution management system wikipedia , lookup
Stray voltage wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Voltage optimisation wikipedia , lookup
Electrical substation wikipedia , lookup
Amtrak's 25 Hz traction power system wikipedia , lookup
Earthing system wikipedia , lookup
Three-phase electric power wikipedia , lookup
Electrification wikipedia , lookup
History of electric power transmission wikipedia , lookup
Rectiverter wikipedia , lookup
Power engineering wikipedia , lookup
Mains electricity wikipedia , lookup
National Electrical Code wikipedia , lookup
Electrical Motors Wiring S. Christian Mariger Ph.D. Biological Systems Engineering Virginia Tech Examples using Ohm’s Law • Determine the resistance of a soldering iron that draws 9.5 amps. The iron is plugged into a 120v outlet. • Volts = amps x resistance or E = IR • R = E/I = 115volts / 9.5 amps = 12.1 Ohms Examples using Ohm’s Law • Determine the resistance of a 100 Watt light bulb on a 120 volt AC circuit. • Watts = volts x amps Examples using Ohm’s Law • Determine the resistance of a 100 Watt light bulb on a 120 volt AC circuit. • Watts = volts x amps • Watts / volts = amps = 100/120 = 0.83 Examples using Ohm’s Law • Determine the resistance of a 100 Watt light bulb on a 120 volt AC circuit. • Watts = volts x amps • Watts / volts = amps = 100/120 = 0.83 • Resistance (Ohms) = volts/amps Examples using Ohm’s Law • Determine the resistance of a 100 Watt light bulb on a 120 volt AC circuit. • Watts = volts x amps • Watts / volts = amps = 100/120 = 0.83 • Resistance (Ohms) = volts/amps • R = 120/0.83 = 145 ohms Electrical Generation & Delivery • Most electricity is generated a great distance from where it is used. • Large AC generators at power plants use induction to convert mechanical energy in to vast quantities of electricity (Three phase AC @ 25,000 volts) • This electrical power is run through a step-up transformer at the power plant to raise the voltage to 765,000 volts for transmission across the electric grid. Power Transmission The “Electrical/Power Grid” is made up of thousands of interconnected high tension towers like this one. These towers carry the high voltage current from the power plant over long distances to special substations called receiving stations. Electrical Power Delivery • The receiving substations house stepdown transformers to reduce the voltage to 34,000 Volts for branch distribution • Branch substation transformers further reduce the voltage to 12,500 Volts • Finally the transformer on the pole outside your house steps the voltage down to 240 or 120 Volts. Power Delivery Receiving Station Electric Service Drop Branch Substation Pole Transformer (Electrical Motors) Electrical Motors • Though lighting and heating are very important, in terms of agricultural structures electrical motors are the most significant application of electrical power. – Ventilation fans – Pumps – Material handling – Etc. Advantages of Electric Motors • • • • • • • Efficiency (50 to over 90%) Low initial cost Relatively inexpensive to operate Easy to start Can be started with a reasonable load Can be remotely/automatically controlled Can withstand temporary overloads Advantages of Electric Motors (Continued) • • • • • • Long service life (35,000 hours) Compact Simple to operate Low noise level No exhaust fumes Minimize safety hazards Single Phase AC Electric Motors • Split Phase (fans and pumps) • Capacitor Start (compressors, augers, pumps and elevators) • Two Valve Capacitor (conveyors, elevators and silo unloaders) • Permanent Split Capacitor (fans and blowers) • Shaded Pole (small blowers and appliances) • Wound Rotor (conveyors, mills/grinders, hoists and deep well pumps) • Universal/Series (portable power tools) • Synchronous (clocks and timers) • Soft Start (crop driers, forage blowers, irrigation pumps, manure agitators) AC Electric Motor Power (P) in Watts • Single Phase Motors: – P = E x I x PF • Three Phase Motors: – P = 1.73 x E x I x PF – Where: • • • • P = Power in (Watts) E = Electromotive force in (Volts) I = Current flow in (Amps) PF = Power Factor Power Factor (PF) • The power factor of an AC electric power system is defined as the ratio of the active (true or real) power to the apparent power. – Where: • Active (Real or True) Power is measured in watts (W) and is the power drawn by the electrical resistance of a system that does useful work. • Apparent Power is measured in volt-amperes (VA) and is the voltage on an AC system multiplied by all the current that flows in it. It is the vector sum of the true and the reactive power. Power Factor (PF) • For purely resistive loads like incandescent lighting and heating elements the power factor is 1.0 so in these special cases: – Power (P) = E x I = Watts • The power factor for inductive or capacitive loads such as electric motors varies by motor type, hp rating, and the mechanical load on the motor. Power factor can vary from 0.3 for unloaded fractional hp motors to nearly 1.0 for large capacitor run motors. Electric Motor Efficiency • Efficiency The power output divided by the total power consumed = – Useful power output / Total power input. • For single phase motors (%) = – ((Rated hp x 746 W/hp) / (E x I x PF)) x 100 • For three phase motors (%) = – ((Rated hp x 746 W/hp) / (1.73 x E x I x PF)) x 100 Electric Motor Data Plate Gives critical data such as: Voltage, Amps, Phase, Hertz, RPM, Power Factor and Duty Rating 25 hp Electric Motor Example • • • • • • • Actual power consumed (P) Watts (3 phase) = 1.73 x E x I x PF P = 1.73 x 230 x 59.4 x 0.843 = 19,925 W Theoretical power output 25hp x 746 W/hp = 18,650 W Efficiency (%) (18,650 / 19,925) x 100 = 93.6% Electric Motor Data Plate Notice how the calculated efficiency is exactly the same as the nominal efficiency on the data plate! Starting Current (Amps) • Refer to the electric motor characteristics table in the handout! • Notice that an electric motor can draw between 1.5 and 8 times the full-load current at start up. • When sizing conductors and overload protection devices for electric motors multiply the full-load amperage by 1.25 or 125% to find the minimum ampacity. Ampacity: the current (amps) a conductor can carry without exceeding it’s temperature rating. (Electrical Wiring) AC Phases • Residential electrical service is exclusively single phase. • However some agricultural applications e.g. some large electric pumps, require three phase power. • Farms and shops will often have high voltage three phase electrical service. • Three phase is more complicated to wire and should be handled by a qualified electrician Distribution Panel • A circuit may have many branches, but in each branch, the delivery wire and the return wire are attached to the corresponding wire on the main circuit. • The main circuit and branch circuits meet at a breaker/fuse box or distribution panel. Types of Branch Circuits • General purpose: 120 V 20-Amps or less. – Permanent lighting and appliances. – Convenience outlets (<1,500 Watts) • Individual: 120 or 240 V – – – – All motors ½ hp or larger Appliances over 1,500 Watts All 240 V applications Continuous service equipment (incubators, milk coolers, brooders, etc.) • The minimum recommended AWG for both types of branch circuits in agricultural applications is 12 gauge (copper). Protection of Branch Circuits • Each branch circuit is protected by it’s own fuse or circuit breaker. • The over-current protective device is selected in accordance maximum current (Amps) that can be carried by the gauge wire used in the circuit. Over-current Protective Devices Circuit Breakers automatically open the circuit when current flow exceeds the breaker rating Fuses have a circuit opening “fusible member” that is directly heated and destroyed by the passage of too much current Fuses and circuit breakers protect the wires and equipment not people! Ground Fault Circuit Interrupter (GFCI) • Fuses and circuit breakers are designed to protect equipment and wiring from current overloads. (These are fairly slow to react) • A GFCI is designed to protect people from stray current and shorts. • The GFCI compares the current on the hot wire to the current on the neutral wire, if the amperage is not equal the GFCI cuts off the current immediately! Designing a Single Phase Branch Circuit 1. 2. 3. 4. Determine the electrical load Measure the length of the run (one-way) Select the appropriate wire gauge Select the appropriate wire insulation type 5. Select the appropriate over-current protective device For all convenience outlets use a GFCI Electrical Load for General Purpose Branch Circuits A. Count the number of lamps or appliances that will be used on the circuit and note the wattage of each. B. Add up the number of watts used on the circuit. C. For a 120 V AC circuit divide the watts by 120 to determine the amp load D. Recall that Watts = Volts X Amps Electrical Loads for Individual Branch Circuits A. Find the full-load current (Amps) for the motor. B. To adjust for starting current multiply the full-load current (Amps) by 1.25 or 125% Measure the length of the run • Measure the distance from the main circuit box to the end of the branch circuit to be wired. • Recall that long runs will cause a voltage drop on the circuit ( No more than a 2% Voltage Drop should be allowed) • For example a five amp load needs only 12 gauge wire to go 50 feet, but will require a 10 gauge wire at 100 feet. Voltage Drop • Is the reduction in voltage between the power supply and the electrical load. This loss occurs any time electricity flows on a conductor such as a wire. Voltage drop is equal to the product of the current (A) and the resistance (Ω) of the conductors in the circuit. • Voltage Drop (%) = ((I x R) / E) x 100 Wire Gauge for (120 Volt) AC Single Phase (Lighting & Outlets) Amp Load 5 amp 10 amp 15 amp 20 amp 30’ 100’ 200’ 300’ 400’ 500’ Run Run Run Run Run Run 12 ga 12 ga 10 ga 8 ga 6 ga 6 ga 12 ga 10 ga 6 ga 4 ga 4 ga 3 ga 12 ga 8 ga 4 ga 4 ga 2 ga 1 ga 12 ga 6 ga 4 ga 2 ga 1 ga 0 ga Copper Wire Insulation Types Wire Type T TW THHN THW XHHW UF Application Dry locations Dry or wet locations Dry locations with high temps Wet locations with high temps High moisture heat resistance Direct burial in soil (not concrete) Livestock and poultry structures are wet and corrosive environments, the use of UF cable, corrosion resistant boxes and fittings are strongly recommended! Making connections • There are a number of ways to make electrical connections: – Screw terminals – Electrical solder – Solder-less connections – Wire nuts – Splices – Etc. Screw terminals • Commonly found on switches, outlets, and lamp holders. • Note the clockwise direction of the connection Soldering connections • Solder is an excellent way to make electrical connections. • Connections are sure and permanent. Solder-less connections • These connections are fast and secure, but must be crimped properly in-order to give good results Wire nuts • Wire nuts are used extensively in wiring homes and agricultural structures. Wire splices • Wire splices are often used as a last resort when one of the preceding methods will not work. Splicing multiple wires • When more than one wire is to be spliced the splices should be staggered to prevent a short circuit. Wire color codes (120 V) Wire color Wire Function Black Positive (hot wire) Red Positive (hot wire) Blue Positive (hot wire) White Neutral (current back to the source) Green Ground (to metal box) Bare Ground (to metal box) Wiring • Switches • Lamp sockets • Outlets Switches • Single pole – • Three way – Single pole switch Three-way switch Three-way circuit Three-way circuit Lamp sockets Convenience outlet Convenience outlet Convenience outlet GFCI outlet GFCI plug GFCI protection can also be built into appliances & extension cords! Circuit Failures • Short – A short circuit occurs when two or more wires come in contact with each other that should not. – May result from worn insulation or a wire becoming unhooked. – Causes a by-pass to be created in the original circuit, reducing the resistance of the circuit. – When the resistance is reduced, current flow or amperage increases producing excessive heat. – Heat can melt insulation, cause circuit breakers to trip, fuses to melt or even damage to electrical equipment. Circuit Failures • Open Circuit – An interruption or break in the flow of electricity. – This can occur when a conductor is accidentally cut, comes loose from its connection or corrosion has created too much resistance in the circuit. – Construction workers digging into underground cables is a common occurrence for the utility companies.