* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download EE 466: VLSI Design
Pulse-width modulation wikipedia , lookup
Stepper motor wikipedia , lookup
Power inverter wikipedia , lookup
Thermal runaway wikipedia , lookup
Variable-frequency drive wikipedia , lookup
Mercury-arc valve wikipedia , lookup
Three-phase electric power wikipedia , lookup
Electrical substation wikipedia , lookup
History of electric power transmission wikipedia , lookup
Electrical ballast wikipedia , lookup
Power electronics wikipedia , lookup
Schmitt trigger wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Semiconductor device wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Voltage regulator wikipedia , lookup
Current source wikipedia , lookup
Surge protector wikipedia , lookup
Rectiverter wikipedia , lookup
Voltage optimisation wikipedia , lookup
Stray voltage wikipedia , lookup
Buck converter wikipedia , lookup
Alternating current wikipedia , lookup
Mains electricity wikipedia , lookup
EE 466: VLSI Design Lecture 03 Channel Length Modulation • • • The inversion layer charge QI represents the total mobile electron charge on the surface and its expression at the source end of the channel is: QI at x=0=-Cox(VGS-VT0) and the inversion layer charge at the drain end of the channel is expressed as: QI at x=L=-Cox(VGS-VT0-VDS) At the edge of saturation when the drain-to-source voltage reaches saturation (VDS=VDSAT=VGS-VT0) the inversion layer charge at the drain end becomes zero. • • • • • We can approximate the inversion layer charge at the drain end by QI at x=L=0 (even though this is not quite true) When VDS=VDSAT, the channel is pinched off at the drain end. Further increase of the drain-tosource voltage (VDS>VDSAT) results in even a larger pinched-off portion of the channel. The effective channel length is reduced to: L’=L-DL where DL is the length of the channel where QI=0. The pinch-off point moves from the drain end of the channel towards the source end with increasing VDS. Channel Length Modulation • For L’<x<L the channel voltage is Vc at x=L’=VDSAT. • The electrons traveling from source to drain traverse the inverted channel segment of length L’ and then they are injected into the depletion region of length DL that separates the pinch-off point from the drain edge. • The gradual channel approximation is valid in this region and is given by: IDSAT=(mnCox)/2(W/L’)[VGS-VT0]2 • The effective channel length for the MOSFET operating in saturation is now L’ and the above equation accounts for the actual shortening of the channel. • Shortening of the channel is also known as channel length modulation. • If L’ is replaced by L in the equation we can show that the computed saturation current using L’ is greater than the new IDSAT computed using L. Channel Length Modulation • We must modify the equation for saturation current so that it reflects the dependency on VDS. Note that the saturation current will increase with increasing VDS since L’ decreases with increasing VDS. I DSAT 1 m C W n ox VGS VT 0 2 1 DL 2 L L • The first term of the equation accounts for the channel length modulation effect. DL VDS VDSAT • Let 1-DL1-lVDS, with l being an empirical model parameter called the channel length modulation coefficient. • Assume that lVDS<<1 then the saturation current becomes: I DSAT mnCox W 2 L VGS VT 0 2 1 lVDS • The above equation can be used with sufficient confidence for most first order hand calculations The Threshold Voltage • • Any gate-to-source voltage less than VT0 is not sufficient to establish an inversion layer. The MOSFET conducts no current between its source and drain terminals unless VGS is greater than VT0. Oxide (SiO2) Metal (Al) P-type Semiconductor (Si) Ec 2FF qVT0 FF FF Ei EFp Ev • • Increasing the gate-to-source voltage above and beyond VT0 will not affect the surface potential and the depletion region depth. There are 4 physical properties that affect the threshold voltage namely (i) the work function difference between the gate and the channel, (ii) the gate voltage component to change the surface potential, (iii) the gate voltage component to offset the depletion region charge and (iv) the voltage component to offset the fixed charges in the gate oxide and in the silicon oxide interface. The Threshold Voltage • The work function difference (Fgate-to-channel) reflects the built in potential of the MOS structure which consists of the p-type substrate, the thin silicon dioxide layer and the gate electrode. • FGC = FF(substrate) –FM if the gate material is metal (Aluminum) • If polysilicon is the gate material: FGC = FF(substrate) – FF (gate) • An externally applied voltage must be changed to achieve surface inversion i.e. to change the surface potential by -2FF. • The depletion region charge density at surface inversion (FS = -FF) is QB0=-(2qNASi|-2FF|)-1/2 • Assuming that the substrate is biased at a different voltage level than the source (at ground) then the depletion region charge density can be expressed as a function of the source-to-body voltage VSB: QB=-(2qNASi|-2FF|+ VSB)-1/2 • The third component offsets the depletion region charge and is equal to –QB/Cox (Cox=ox/tox). The Threshold Voltage • The gate voltage that is necessary to offset to the fixed positive charge density Qox (at the interface between the gate oxide and the silicon substrate) is –Qox/Cox. • Combining all the voltage components we can determine the threshold voltage. For zero substrate bias VT0 is given by: VT0=FGC-2FF-QB0/Cox-Qox/Cox • Thus determine the expression for nonzero substrate bias. Body effect • The most general form of the threshold voltage is: VT=FGC2FF-Qox/Cox-QB/Cox VT VT 0 2F F VSB 2F F • VT=VT0-(QB-QB0)/Cox • (QB-QB0)/Cox=((2qNASi)-1/2) /Cox*((|-2FF+VSB|)-1/2-(|2FF|)-1/2) • This becomes the most general expression of the threshold voltage with the parameter gamma being: 2qN A Si Cox The Threshold Voltage • Gamma is called the substratebias or the body effect coefficient. • The general expression for the threshold voltage can be used for both the n-channel and p-channel devices. • The differences are as follows: – Substrate Fermi potential FF is negative in nMOS but positive for pMOS. – The depletion region charge densities QB0 and QB are negative for nMOS but positive for pMOS • Further differences: – The substrate bias coefficient is positive for nMOS and negative for pMOS. – The substrate bias voltage VSB is positive in nMOS but negative for pMOS. • Typically the threshold voltage of an enhancement mode n-type MOSFET is a positive quantity while that of a p-type MOSFET is negative. Sub-Threshold Conduction • • • • • • Ideally at VGS < VT, ID = 0. The MOS device is partially conducting for gate voltages below the threshold voltage. This is termed sub-threshold or weak inversion conduction. In most digital applications the presence of sub-threshold current is undesirable. Why? ….most digital applications …. Does this mean some digital applications can tolerate sub-threshold currents? A Sub-threshold digital circuit manages to satisfy the ultra-low power requirement. How? • What type of digital applications can benefit from this ultra low power design approach? Subthreshold Conduction • Below cut off current does not abruptly become zero Vgs Vt I ds I ds0 e • Falls off exponentially nvT (1 e Vds vT ) I ds0 v e 2 1.8 T • Useful in low power CMOS VLSI design Junction Leakage • Conduction even when transistor is in cut-off • Substrate to diffusion junctions are reverse biased • However reverse biased diodes do conduct leakage current I D I S (e VD vT 1) Leakge Current • When the junction bias voltage is significantly more than the thermal voltage (~26mV @room temperature) the leakage current is –Is • Junction leakage limits storage time in onchip memory elements – Requires refreshing dynamic nodes Tunneling effects • Ideal MOS model – High input impedence – No static current flow through the gate terminal • Quantum mechanical effect – Carriers “tunnel” through insulating barriers with finite probability – Insulating barrier has to be very thin for appreciable current • Current gate oxide thickness ~10-15Å – Single atomic layer of silicon ~3Å Tunneling current • Current technology nodes – Tunneling current as significant as junction leakage and sub-threshold conduction • Technique to reduce tunneling current – Use high-K materials in the gate oxide layer • High dielectric constant makes high gate capacitance – Reduces the need to reduce the oxide thickness – Silicon Nitride is a good candidate for such materials Temperature Effects • Effect on Mobility • Carrier mobility decreases with temperature • kµ is a parameter usually in the range 1.2-2.0 T m (T ) m (Tr ) Tr km Temperature effects • Threshold voltage – Vt decreases linearly with increase in temperature • Junction leakage also increases with increase in temperature • All combined results in decrease of On current and increase of Off current Temperature Issues • Circuit performance is therefore generally worse at high temperatures • Conversely cooling can enable better performance • Cooling techniques – Convection • Natural • Fans • Heat sinks – Active cooling • Water cooling • Liquid nitrogen • Cost of methods have to be justified Non-Ideal I-V Effects (Summary) • Miniaturization has led to modern devices having nonideal characteristics • The saturation current increases less than quadratically with increasing VGS. • Velocity saturation and mobility degradation are two of the effects that cause the non quadratic current increase with VGS. • When carrier velocity ceases to increase linearly with field strength we have velocity saturation. • The current IDS is lower than expected at high VDS. • There are several sources of leakage that result in current flow when the transistor is expected to be OFF. • The source and drain diffusion regions are form reverse biased diodes which experience junction leakage into the substrate or well. • The current into the gate IG is ideal zero, however as gate oxide thickness is reduced electrons tunnel through the gate, causing some current.