* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Design technique for all-dielectric non
Laser beam profiler wikipedia , lookup
Ultrafast laser spectroscopy wikipedia , lookup
Reflector sight wikipedia , lookup
Rutherford backscattering spectrometry wikipedia , lookup
Optical flat wikipedia , lookup
Optical amplifier wikipedia , lookup
Thomas Young (scientist) wikipedia , lookup
Fiber-optic communication wikipedia , lookup
Optical rogue waves wikipedia , lookup
Smart glass wikipedia , lookup
Atmospheric optics wikipedia , lookup
Optical aberration wikipedia , lookup
3D optical data storage wikipedia , lookup
Surface plasmon resonance microscopy wikipedia , lookup
Photon scanning microscopy wikipedia , lookup
Dispersion staining wikipedia , lookup
Passive optical network wikipedia , lookup
Optical coherence tomography wikipedia , lookup
Silicon photonics wikipedia , lookup
Nonimaging optics wikipedia , lookup
Magnetic circular dichroism wikipedia , lookup
Ultraviolet–visible spectroscopy wikipedia , lookup
Interferometry wikipedia , lookup
Optical tweezers wikipedia , lookup
Refractive index wikipedia , lookup
Nonlinear optics wikipedia , lookup
Ellipsometry wikipedia , lookup
Birefringence wikipedia , lookup
Harold Hopkins (physicist) wikipedia , lookup
OPTO−ELECTRONICS REVIEW 20(1), 96–99 DOI: 10.2478/s11772−012−0012−3 Design technique for all-dielectric non-polarizing beam splitter plate A. RIZEA* Optical Coatings Department of Pro Optica S.A., 67 Gheorghe Petrascu Str., 031−593 Bucharest, Romania There are many situations when, for the proper working, an opto−electronic device requiring optical components does not change the polarization state of light after a reflection, splitting or filtering. In this paper, a design for a non−polarizing beam splitter plate is proposed. Based on certain optical properties of homogeneous dielectric materials we will establish a relia− ble thin film package formula, excellent for the start of optimization to obtain a 20−nm bandwidth non−polarizing beam splitter. Keywords: optical coatings, beam splitter, non−polarizing. 1. Introduction As it is known, the reflected light on the surface of a glass plate has a certain degree of polarization depending on the refractive index of the glass plate and the angle of incidence of radiation [1,2]. In this proposed application, the light is incident from air to a BK7 optical glass plate (nd »1.52), un− der an incidence angle of q0 = 45°. Under such conditions our target is to obtain quasi−equal values for Ts, Tp, Rs, and Rp for the nominal ratio R/T = 1, where: Ts is the s−polarized component of the transmitted light, Tp is the p−polarized component of the transmitted light, Rs is the s−polarized component of the reflected light, Rp is the p−polarized component of the reflected light, R is the total reflected light, T is the total transmitted light. In our article we will note “H” “M” or “L” as materials used to describe the thin layers package formula representing “High”, “Medium” or “Low” index, respectively. Optical thickness of each layer has the value obtained by multiplying the factor before the symbol with the reference wavelength (l0 = 550 nm) and divided by four. Thus, “0.5H” represents a layer of material (substance) “H” with optical thickness 0.5(550 4) nm. When a structure is repeated, that structure can be written in parentheses and number of repetitions is written on the right side−up. e.g. L H L H L H º (L H)3. Applied theory of thin optical layers (ATTOL) is a soft− ware application achieved by the author of this article, used for numerical simulations and optimizations. Over the time, this software has demonstrated a high accuracy in the design of optical coatings. Now, in order to obtain a beam splitter with R/T = 1 and to achieve the “non−polarizing” attribute, it is necessary to find solutions based on some optical properties of materials or more specific optical phenomena. In the literature, vari− l l l ous solutions are presented in Refs. 6–9, but this article will explain how an original solution was found – a structure with only seventeen layers, every layer having an optical thickness of l0/4 or very close to this value. 2. Short theory In the theory of a thin optical layer, the term named “effec− tive refractive index” was introduced [3,4]. This is the refractive index of a medium relative to the state of polariza− tion of radiation that crosses it. Thus, for the two linearly polarized components “p” and “s” l np = n/cosq, (1) ns = n cosq, (2) l l *e−mail: 96 [email protected], [email protected] where np and ns are the “effective refractive indices” of the layer considered for the two components (“p” and “s”) of radiation, n is the nominal refractive index of the layer, q is the angle under the radiation passing through the layer. This is the angle of refraction, resulted from the Snell Eq. n1sin(i) = n2sin(q). Also, the optical thickness of each layer is multiplied by cosq and is named “the effective thickness”. By using the Snell law we obtain [5] l l æ A2 ö ÷ cos q = çç 1 ÷ è n2 ø 12 , (3) where A is n0sinq0 (numerical aperture) and it is a constant in the entire thin layers package, n is the nominal refractive index, q0 is the angle of incidence, n0 is the refractive index of air. From Eqs. (1), (2), and (3) we obtain [5] Opto−Electron. Rev., 20, no. 1, 2012 Unauthenticated Download Date | 8/12/17 7:47 PM np = n 2 [1 - ( A n 2 )]1 2 æ A2 ö ÷ n s = n çç 1 ÷ è n2 ø , (4) 12 . (5) Figures 1 and 2 represent two cases of variations of these effective refractive indices (np and ns) as functions of the nominal index of refraction n, for q0 = 45°: first case (Fig. 1) – the light is incident from optical glass BK7 (n0 = 1.52). This is the case of a beam splitter cube, second case (Fig. 2) – the light is incident from air (n0 = 1). This is the case of a beam splitter plate. Now, we can notice a major difference between the two cases: if the incident light is coming from a higher index me− dium, ns has a positive slope, while the np has a mini− mum even for n = n0 = 1.52, if the light is incident from air, the variation of np does not show a minimum. The first case when the light is incident from glass was very ingeniously solved by Gilo in order to design a non− −polarizing beam splitter inside a glass cube [5]. He noted that if two different materials whose effective refractive indices (np1 and np2) are the one part and another one of the minimum at equal distance from it (Fig. 1) are selected, then np1 »np2 and it is possible to build a thin layers package that affects only the “s” transmission component Ts in order to manage a balance from the two components of the total transmission T in a proximity of the nominal value of 50%. Now, what we can do in the second case (Fig. 2) when we cannot get two materials with quasi–equal values of np? (np1 »np2) However, we can notice some peculiarities in this case too. l l Fig. 2. Effective refractive indices (np and ns) as functions of nomi− nal index of refraction (n) for an incidence from air (n0 = 1 and q0 = 45°). l l struct a thin film package with two materials (H and M1) from the right side of the graph, we get a decrease in trans− mission, but with a minimum difference between Ts and Tp (Fig. 3). The first step is to construct a package with these two materials in order to get a decrease in transmission around the value of 30%. The two selected materials for the first package are: H (high index): nd = 2.3 (e.g. TiO2), M1 (medium−high index): nd = 1.8 (e.g. Paso II from Umicore), And the coating structure is l l Air – (M1 H)6 – BK7 . (6) By looking closer we can observe that the difference between the two slopes is smaller in the right side of the graph than in the left side (Fig. 2). That means if we con− The resulted transmissions are presented in Fig. 3. The second step is to increase the transmission around the value of 50% with a new interferential package but this time we choose a pair of material in the left side of the graphic (see Fig. 2.) where we can see that the difference between the two slopes ns and np is higher than the differ− ence in the right side of the graph. We use this difference to act more strongly on the component “s”, in order to manage a balance from the two components of transmission. Fig. 1. Effective refractive indices (np and ns) as functions of nomi− nal index of refraction n for an incidence from BK7 optical glass (n0 = 1.52 and q0 = 45°). Fig. 3. Spectral transmissions (Ts and Tp) through a coated BK7 glass [Eq. (6)] for an incidence of q0 = 45o. 3. Coating design Opto−Electron. Rev., 20, no. 1, 2012 97 A. Rizea Unauthenticated Download Date | 8/12/17 7:47 PM Design technique for all−dielectric non−polarizing beam splitter plate l l The two selected materials for the second package, are: M2 (medium−low index): nd = 1.63 (e.g. Al2O3) L (low index): nd = 1.38 (e.g. MgF2) The new added structure is (M2 L) M2 (L M2) . (7) And the new global structure is Air – (M1 H)6 (M2 L) M2 (L M2) – BK7 . (8) The resulted transmissions are presented in Fig. 4. Fig. 6. Spectral transmission Ts and Tp (magnified scale) through a coated BK7 glass [Eq. (9)] for an incidence of q0 = 45°. 4. Conclusions Fig. 4. Spectral transmission Ts and Tp through a coated BK7 glass [Eq. (8)] for an incidence of q0 = 45°. Of course, the third step is the numeric optimization. This is done with a specialized software (ATTOL), but we can see that in this case the problem has been solved with the original structure made of layers with quarter−wave− length thick. However, certain improvements obtained after the optimization can be seen in Figs. 5 and 6. The refined coating structure is Air – 0.93M1 H 1.02M1 1.02H 1.01M1 1.02H 1.02M1 1.04H 1.05M1 1.05H 1.07M1 0.92H 0.84M2 1.04L 1.14M2 1.27L 0.89M2 – BK7 (9) In this paper, a non−polarizing design concept is shown, based on the optical properties of the effective indices of the selected materials. Like Mackowski said while presenting his results, con− cerning the achievement of a non−polarizing beam splitter, “the design of dielectric coatings in order to have equal p and s polarization over a wide spectral region is exceptio− nally difficult” [6]. However, for narrow spectral domains some solutions can be found that can help to reduce the degree of polarization to negligible values. Great results can be obtained by using anisotropic thin films, but the solution presented in this article had as imposing to use only isotro− pic and homogeneous media [7]. Also, there are applica− tions that allow us to achieve the non−polarizing attribute by a mixed coating metal−dielectric package [8], having the advantage of a wider non−polarizing spectral band, but there are other applications such as systems that use high power densities of light (e.g. focused laser beam) or systems that are used in unfavorable environmental conditions (e.g. excessive humidity or salinity), when all−dielectric package coating is the only option, because all−dielectric package has an advantage of a net superior resistence and reliability. At the end of this article some features of the proposed design could be mentioned: every stage of design was explained and justified from theoretical point of view and the results meet the theore− tical predictions. The results presented in this form [Eq. (9) and Fig. 5 and 6] can be easily verified with any pro− fessional software specialized in optical coatings design, the proposed non−polarizing beam splitter design is one of those with the fewest layers component (only 17), com− pared to the others also presented in the literature [9], in addition to the fact that the optimized coating Eq. (9) (Figs. 5 and 6) can respond to high level requirements, the proposed design gives very good results since it is in the state of unrefined quarter wave layers package [8] (Fig. 4). This can be very helpful for the mass production, l l l Fig. 5. Spectral transmission Ts and Tp through a coated BK7 glass [Eq. (9)] for an incidence of q0 = 45°. 98 Opto−Electron. Rev., 20, no. 1, 2012 © 2012 SEP, Warsaw Unauthenticated Download Date | 8/12/17 7:47 PM l l refined Eq. meets 49% < R < 51% and Rs - Rp < 2%, centered on 550 nm wavelength, the same structure remains valid for other spectral bands centered on different wavelengths. The translation can be done by increasing or decreasing of the layer thick− ness of the quarter−wavelength structure Eq. (8) in the same ratio then it must run a new numeric optimization. References 1. M. Born and E. Wolf, Principles of Optics, Cambrige Uni− versity Press, New York, 1999. 2. I.M. Popescu, Macroscopic Electromagnetic Theory of Light, Scientific and Encyclopedic Publishing, Bucharest, 1986. 3. H.A. Macleod, Thin−Film Optical Filters, Institute of Phy− sics Publishing, Bristol, 1999. Opto−Electron. Rev., 20, no. 1, 2012 4. A. Thelen, Design of Optical Interference Coatings, Printed by McGraw−Hill Inc., 1989. 5. M. Gilo, “Design of a nonpolarizing beam splitter inside a glass cube”, Appl. Opt. 31, 5345–5349 (1992). 6. J.M. Mackowski, “Coatings principles”, in Optics in Astro− physics: NATO Science Series, Vol. 198, pp. 327–342, edi− ted by R. Foy and F.C. Foy, Springer, 2005. 7. H.J. Qi, J.D. Shao, R.J. Hong, K. Yi, and Z.X. Fan, “Non−po− larizing beam splitter design”, Europhys. Lett. 67, 859 (2004). 8. F. Bridou, M. Cuniot−Ponsard, J.M. Desvignes, A. Gottwald, U. Kroth, and M. Richter, “Polarizing and non−polarizing mirrors for the hydrogen Lyman−a radiation at 121.6 nm”, Appl. Phys. A102, 641–649 (2011). 9. M. Tilsh and K. Hendrix, “Optical interference coatings de− sign contest 2007: triple bandpass filter and nonpolarizing beam splitter”, Appl. Opt. 47, C55–C69 (2008). 99 A. Rizea Unauthenticated Download Date | 8/12/17 7:47 PM