* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Ch 5 Homework - ECM
Stepper motor wikipedia , lookup
Three-phase electric power wikipedia , lookup
Power engineering wikipedia , lookup
Thermal runaway wikipedia , lookup
Ground (electricity) wikipedia , lookup
Immunity-aware programming wikipedia , lookup
Variable-frequency drive wikipedia , lookup
History of electric power transmission wikipedia , lookup
Electrical ballast wikipedia , lookup
Electrical substation wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Power inverter wikipedia , lookup
Earthing system wikipedia , lookup
Mercury-arc valve wikipedia , lookup
History of the transistor wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Current source wikipedia , lookup
Voltage regulator wikipedia , lookup
Power electronics wikipedia , lookup
Voltage optimisation wikipedia , lookup
Alternating current wikipedia , lookup
Power MOSFET wikipedia , lookup
Stray voltage wikipedia , lookup
Buck converter wikipedia , lookup
Semiconductor device wikipedia , lookup
Mains electricity wikipedia , lookup
Network analysis (electrical circuits) wikipedia , lookup
Current mirror wikipedia , lookup
ECM 204 Ch 5 Homework True/False Indicate whether the statement is true (T) or false(F). Place either T or F in the space provided. ____ 1. A PC board must be handled under static-free conditions only. a. True b. False ____ 2. The fundamental line frequently in the U.S. is 60 Hz. a. True b. False ____ 3. Diodes are marked or shaped to indicate their anode and cathode. a. True b. False ____ 4. Computer operation cannot be adversely affected by momentary power interruptions. a. True b. False ____ 5. Heat sinks are devices that conduct and dissipate heat away from a component. a. True b. False ____ 6. Static electricity discharge is a major cause of electronic failure. a. True b. False ____ 7. A half-wave rectifier is a circuit containing a diode that permits only the negative half-cycle of the AC sine wave to pass. a. True b. False Multiple Choice Identify the one choice that best completes the statement or answers the question and place your answer in the space provided.. ____ 8. _____ voltage is temporary, undesirable voltage in an electrical circuit. a. Transverse c. Transparent b. Transient d. Translucent ____ 9. A voltage sag is a ____ decrease below the normal rated line voltage. a. 0%-5% c. 10%+ b. 5%-10% d. none of the above ____ 10. A(n) _____ is a solid-state control device that is programmed and reprogrammed to automatically control an industrial process or machine. a. I/O c. CPU b. PLC d. PC ____ 11. A voltage swell is a ____ increase above the normal rated line voltage. a. 0% c. 10%+ b. 5%-10% d. none of the above ____ 12. A ______ is a material that has little resistance and permits electrons to move through it easily. a. conductor c. resistor b. semiconductor d. none of the above ____ 13. ______-type material is material with empty spaces (holes) in its crystalline structure. a. P c. PN b. N d. NP ____ 14. A ____ rectifier is a circuit containing four diodes. a. half-wave c. bridge b. full-wave d. none of the above ____ 15. A ____ sensor is a device that reacts to the proximity of a target without physical contact. a. manual c. proximity b. physical d. thermal ____ 16. A _____ is a device that produces electricity when two different metals that are joined together are heated. a. thermistor c. triac b. transducer d. thermocouple Short Answer Use the following word bank to answer the completion questions. Be sure to copy and spell the word exactly as it is listed. solid-state diode relay contact inverter leakage phototransistor LED rectifier holding timer PC partial transistor open 17. A(n) _____ device is an electronic component such as a diode, SCR, transistor, or integrated circuit that switches or controls the flow of current in a circuit. 18. A(n) _____ board is an insulating material such as fiberglass or phenolic with conducting paths laminated to one or both sides of the board. 19. A(n) ____ is a diode that produces light when current flows through it. 20. A(n) ____ is an electrical component that converts AC to DC by allowing voltage and current to move in only one direction. 21. A(n) ____ is a three-terminal device that controls current flow depending on the amount of voltage applied to the base. 22. A(n) ____ is a device that controls one electrical circuit by opening and closing contacts in another circuit. 23. _____ current is the small amount of current flowing through a solid-state device when it is not conducting. 24. A(n) ____ is a control device that uses a preset time period as part of the control function. 25. A(n) ____ is a machine, device, or system that changes DC voltage into AC voltage and can be designed to produce variable frequency. 26. A(n) _____ is an electronic component that allows current to pass in only one direction. 27. A(n) ____ fault is the malfunctioning of only a section or several sections of a machine. 28. ____ current is the minimum current required to keep an SCR conducting. 29. A(n) ____ is a device that combines the effect of a photodiode and the switching capability of a transistor. ECM 204 Ch 5 Homework Answer Section TRUE/FALSE 1. 2. 3. 4. 5. 6. 7. T T T F T T F MULTIPLE CHOICE 8. 9. 10. 11. 12. 13. 14. 15. 16. B C B C A B C C D SHORT ANSWER 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. solid-state PC LED rectifier transistor relay Leakage timer inverter diode partial Holding phototransistor