Download Example: [Boylestad 10 th Ed. Eg 9.6

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Transistor wikipedia , lookup

Power inverter wikipedia , lookup

Ground loop (electricity) wikipedia , lookup

Islanding wikipedia , lookup

History of electric power transmission wikipedia , lookup

Rectifier wikipedia , lookup

Topology (electrical circuits) wikipedia , lookup

Signal-flow graph wikipedia , lookup

Electrical ballast wikipedia , lookup

Electrical substation wikipedia , lookup

Power electronics wikipedia , lookup

Voltage optimisation wikipedia , lookup

Ohm's law wikipedia , lookup

Two-port network wikipedia , lookup

Surge protector wikipedia , lookup

Distribution management system wikipedia , lookup

Stray voltage wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Metadyne wikipedia , lookup

Buck converter wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Mains electricity wikipedia , lookup

Opto-isolator wikipedia , lookup

Alternating current wikipedia , lookup

Current mirror wikipedia , lookup

Current source wikipedia , lookup

Network analysis (electrical circuits) wikipedia , lookup

Transcript
ECA1212
Introduction to Electrical &
Electronics Engineering
Chapter 2: Circuit Analysis Techniques
by Muhazam Mustapha, September 2011
Learning Outcome
By the end of this chapter students are
expected to:
• Understand and perform calculation on
circuits with mesh and nodal analysis
techniques
• Be able to transform circuits based on
Thevenin’s or Norton’s Theorem as
necessary
Chapter Content
•
•
•
•
•
Mesh Analysis
Nodal Analysis
Source Conversion
Thevenin’s Theorem
Norton’s Theorem
Mesh
Mash Analysis
CO2
Mesh Analysis
Steps:
• Assign a distinct current in clockwise direction
to each independent closed loop of network.
• Indicate the polarities of the resistors depending
on individual loop.
• [*] If there is any current source in the loop path,
replace it with open circuit – apply KVL in the
next step to the resulting bigger loop. Use back
the current source when solving for current.
CO2
Mesh Analysis
Steps: (cont)
• Apply KVL on each loop:
– Current will be the total of all directions
– Polarity of the sources is maintained
• Solve the simultaneous equations.
CO2
Mesh Analysis
Example: [Boylestad 10th Ed. E.g. 8.11 - modified]
R2
R1
R3 4Ω
2Ω
I1
2V
CO2
a
Ia
I3
1Ω
b
I2
Ib
6V
Mesh Analysis
Example: (cont)
Loop a: 2 = 2Ia+4(Ia−Ib) = 6Ia−4Ib
Loop b: −6 = 4(Ib−Ia)+Ib = −4Ia+5Ib
After solving: Ia = −1A, Ib = −2A
Hence: I1 = 1A, I2 = −2A, I3 = 1A
CO2
Nodal
Noodle Analysis
CO2
Nodal Analysis
• Determine the number of nodes.
• Pick a reference node then label the rest with
subscripts.
• [*] If there is any voltage source in the branch,
replace it with short circuit – apply KCL in the
next step to the resulting bigger node.
• Apply KCL on each node except the reference.
• Solve the simultaneous equations.
CO2
Nodal Analysis
Example: [Boylestad 10th Ed. E.g. 8.21 - modified]
a
I2
R2
b
12Ω
I3
I1
4A
CO2
R1
2Ω
6Ω
R3
2A
Nodal Analysis
Example: (cont)
Node a:
Va Va  Vb
4 
 7Va  Vb  48
2
12
Node b:  2  Vb  Va  Vb  V  3V  24
a
b
6
12
After solving: Va = 6V, Vb = − 6A
Hence: I1 = 3A, I2 = 1A, I3 = −1A
CO2
Mesh vs Nodal Analysis
• Mesh: Start with KVL, get a system of
simultaneous equations in term of current.
• Nodal: Start with KCL, get a system of
simultaneous equations on term of voltage.
• Mesh: KVL is applied based on a fixed loop
current.
• Nodal: KCL is applied based on a fixed node
voltage.
CO2
Mesh vs Nodal Analysis
• Mesh: Current source is an open circuit and it
merges loops.
• Nodal: Voltage source is a short circuit and it
merges nodes.
• Mesh: More popular as voltage sources do exist
physically.
• Nodal: Less popular as current sources do not
exist physically except in models of electronics
circuits.
CO2
Thevenin’s Theorem
CO2
Thevenin’s Theorem
Statement:
Network behind any two terminals of
linear DC circuit can be replaced by an
equivalent voltage source and an
equivalent series resistor
• Can be used to reduce a complicated network
to a combination of voltage source and a series
resistor
CO2
Thevenin’s Theorem
• Calculate the Thevenin’s resistance, RTh, by
switching off all power sources and finding the
resulting resistance through the two terminals:
– Voltage source: remove it and replace with short
circuit
– Current source: remove it and replace with open
circuit
• Calculate the Thevenin’s voltage, VTh, by
switching back on all powers and calculate the
open circuit voltage between the terminals.
CO2
Thevenin’s Theorem
Example: [Boylestad 10th Ed. E.g. 9.6 - modified]
Convert the following network into its
Thevenin’s equivalent:
3Ω
6Ω
9V
CO2
Thevenin’s Theorem
Example: [Boylestad 10th Ed. E.g. 9.6 - modified]
RTh calculation:
3Ω
6Ω
CO2
RTh  3 6  2
Thevenin’s Theorem
Example: [Boylestad 10th Ed. E.g. 9.6 - modified]
VTh calculation:
3Ω
6Ω
9V
CO2
6
VTh 
 9  6V
3 6
Thevenin’s Theorem
Example: [Boylestad 10th Ed. E.g. 9.6 - modified]
Thevenin’s equivalence:
2Ω
6V
CO2
Norton’s Theorem
CO2
Norton’s Theorem
Statement:
Network behind any two terminals of
linear DC circuit can be replaced by an
equivalent current source and an
equivalent parallel resistor
• Can be used to reduce a complicated network
to a combination of current source and a parallel
resistor
CO2
Norton’s Theorem
• Calculate the Norton’s resistance, RN, by
switching off all power sources and finding the
resulting resistance through the two terminals:
– Voltage source: remove it and replace with short
circuit
– Current source: remove it and replace with open
circuit
• Calculate the Norton’s voltage, IN, by switching
back on all powers and calculate the short
circuit current between the terminals.
CO2
Norton’s Theorem
Example: [Boylestad 10th Ed. E.g. 9.6 - modified]
Convert the following network into its
Norton’s equivalent:
3Ω
6Ω
9V
CO2
Norton’s Theorem
Example: [Boylestad 10th Ed. E.g. 9.6 - modified]
RN calculation:
3Ω
6Ω
CO2
RN  3 6  2  RTh
Norton’s Theorem
Example: [Boylestad 10th Ed. E.g. 9.6 - modified]
IN calculation:
3Ω
6Ω
9V
CO2
9
I N   3A
3
Norton’s Theorem
Example: [Boylestad 10th Ed. E.g. 9.6 - modified]
Norton’s equivalence:
OR,
3A
CO2
2Ω
We can just take the
Thevenin’s equivalent and
calculate the short circuit
current.
Maximum Power Consumption
An element is consuming the maximum power out
of a network if its resistance is equal to the
Thevenin’s or Norton’s resistance.
CO2
Source Conversion
Use the relationship between Thevenin’s and
Norton’s source to convert between voltage and
current sources.
2Ω
3A
6V
V = IR
CO2
2Ω