* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download SG-02-0062 A1 KCCA0039 Series Motor
Electrical ballast wikipedia , lookup
Flip-flop (electronics) wikipedia , lookup
Immunity-aware programming wikipedia , lookup
Power inverter wikipedia , lookup
Current source wikipedia , lookup
PID controller wikipedia , lookup
Electrical substation wikipedia , lookup
Pulse-width modulation wikipedia , lookup
Distributed control system wikipedia , lookup
Induction motor wikipedia , lookup
Analog-to-digital converter wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Distribution management system wikipedia , lookup
Alternating current wikipedia , lookup
Stray voltage wikipedia , lookup
Integrating ADC wikipedia , lookup
Brushed DC electric motor wikipedia , lookup
Surge protector wikipedia , lookup
Power electronics wikipedia , lookup
Control system wikipedia , lookup
Voltage regulator wikipedia , lookup
Stepper motor wikipedia , lookup
Control theory wikipedia , lookup
Buck converter wikipedia , lookup
Mains electricity wikipedia , lookup
Voltage optimisation wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Schmitt trigger wikipedia , lookup
Lift Pump 24-Volt Motor Controller KCCA0039 Features Kinetek KCCA0039 motor controllers are a low cost, high performance solution for pump motor control applications including scissor lifts, lift trucks, mobile booms, or any pumping application where 24-volt, series motor, speed control is employed. • Current limiting: 360 Amps • Operating voltage: 12 to 32 Volts DC, 300 to 400 Amps • Input voltage range: 0 to 5 Volts DC KCCA0039 controllers keep cost low while emphasizing tough, solid-state durability and performance over time. Controllers provide circuit over-voltage protection, control input over-voltage protection, and control output over-voltage protection. • Enable input: 12V DC or greater, (10 mA max) • Speed input over voltage protection The controller speed input uses a 0 to 5-volt linear DC voltage, usually provided by a simple 5 to 10k Ohm potentiometer, and a separate 12-volt or greater Enable input. At 0.5 Volts, the controller begins providing voltage to the motor at a minimum duty cycle of 7.0%. The duty cycle increases linearly with speed input voltage up to 3.86 volts at which point the duty cycle is 100%. If the controller measures 4.6 volts or more on the speed control input, or 5.6 volts or more on the speed control output circuit, for longer than 100mS, the controller will shut down. If the controller detects circuit voltage outside its 12 to 32 volt operating range, for longer than 0.5 seconds, it will likewise shut down. Logical shut down occurs before motor or controller can be damaged. The controller is easily reset by cycling the Enable input. Simple mounting and easy-connect blade terminals for control connections make the KCCA0039 easy to install and connect. The rugged enclosure provides durable protection for electronic circuitry. • Speed output circuit over voltage protection • Operating circuit over voltage protection • Easy connect blade-style (Faston) control connections • Rugged enclosure Applications • Material handling lifts • Scissor lifts • Lift trucks • Mobile booms • Appropriate pump motor applications Kinetek Controls 3705 Lane Rd. Perry, OH 44081 Phone: (440) 357-5711 Fax: (440) 357-5440 Email: [email protected] Web: www.kinetekcontrols.com SG-02-0062 A1 KCCA0039 Series Mo1 1 1/21/2008 10:13:43 AM Lift Pump 24-Volt Motor Controller Electrical Operation • Enable Input: A voltage greater than 12V (10mA maximum load) must be applied to enable the control. • Speed Input: Once enabled, a 0 to 5V linear signal controls motor speed. Designed to operate with a 5 to 10k Ohm potentiometer. Potentiometer wiper is connected to the speed input with the remaining two potentiometer connections made to the +5V potentiometer supply and B-. • Shutdown reset: Cycle Enable input power. Dimensions Kinetek Controls 3705 Lane Rd. Perry, OH 44081 Phone: (440) 357-5711 Fax: (440) 357-5440 Email: [email protected] Web: www.kinetekcontrols.com SG-02-0062 A1 10/2307 SG-02-0062 A1 KCCA0039 Series Mo2 2 1/21/2008 10:14:06 AM