Soft Errors - CS Course Webpages
... Soft error mitigation techniques are to provide partial immunity of a design to potential soft errors while significantly minimizing the required cost over fault tolerance schems. There are three soft error mitigation methods: (1) Built-In Soft-Error Resilience (BISER) BISER proposed in [Mitra 2005] ...
... Soft error mitigation techniques are to provide partial immunity of a design to potential soft errors while significantly minimizing the required cost over fault tolerance schems. There are three soft error mitigation methods: (1) Built-In Soft-Error Resilience (BISER) BISER proposed in [Mitra 2005] ...
AN-5015 USB1T11A Transceiver and Specification Compliance AN- 5015 US
... USB1T11A Transceiver and Specification Compliance Introduction The Universal Serial Bus (USB) specification has become widely accepted as the preferred mechanism for low to medium speed serial data interfaces. Older connections like RS232 and parallel printer LPTx ports can only be connected to one ...
... USB1T11A Transceiver and Specification Compliance Introduction The Universal Serial Bus (USB) specification has become widely accepted as the preferred mechanism for low to medium speed serial data interfaces. Older connections like RS232 and parallel printer LPTx ports can only be connected to one ...
TPD1E6B06 Single-Channel ESD Protection Diode in 0201
... so that this protection device is a good fit for GPIO and especially audio lines which carry bidirectional signals. Low leakage current allows the diode to conserve power when working below the VRWM. The industrial temperature range of –40°C to 125°C makes this ESD device to work well at extensive t ...
... so that this protection device is a good fit for GPIO and especially audio lines which carry bidirectional signals. Low leakage current allows the diode to conserve power when working below the VRWM. The industrial temperature range of –40°C to 125°C makes this ESD device to work well at extensive t ...
ICS854105 - Integrated Device Technology
... express or implied, including, but not limited to, the suitability of IDT’s products for any particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any license under ...
... express or implied, including, but not limited to, the suitability of IDT’s products for any particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any license under ...
Voltage Level Translation Guide Auto-Direction Sensing Direction Controlled
... AC-transitions to maintain fast data rate throughput • VCC isolation feature — if either VCC input is at GND, all outputs are in the high impedance state • Highly integrated ESD protection — ±15-kV ESD protection on the B port • Devices ending in E suffix include integrated IEC 61000-4-2 ESD pr ...
... AC-transitions to maintain fast data rate throughput • VCC isolation feature — if either VCC input is at GND, all outputs are in the high impedance state • Highly integrated ESD protection — ±15-kV ESD protection on the B port • Devices ending in E suffix include integrated IEC 61000-4-2 ESD pr ...
LED measurement
... In lighting applications we can differentiate high frequency flicker or stroboscopic effects and low frequency flicker often caused by bad power supplies. Flicker is typically measured by means of human vision corrected sensors (CIE1931 luminance response) typically excluding flicker occurring in w ...
... In lighting applications we can differentiate high frequency flicker or stroboscopic effects and low frequency flicker often caused by bad power supplies. Flicker is typically measured by means of human vision corrected sensors (CIE1931 luminance response) typically excluding flicker occurring in w ...
AN-2134 LMZ13610/8/6 and LMZ12010/8/6
... The LMZ13610/8/6 and LMZ12010/8/6 SIMPLE SWITCHER® power modules are easy-to-use DC-DC solution capable of driving up to a 10, 8 or 6 ampere load. They are available in an innovative package that enhances thermal performance and allows for hand or machine soldering. The LMZ13610/8/6 can accept an in ...
... The LMZ13610/8/6 and LMZ12010/8/6 SIMPLE SWITCHER® power modules are easy-to-use DC-DC solution capable of driving up to a 10, 8 or 6 ampere load. They are available in an innovative package that enhances thermal performance and allows for hand or machine soldering. The LMZ13610/8/6 can accept an in ...
trade: instrument mechanician
... According to the applicable regulations of the Mines and Works Act or the Machinery and Occupational Safety ...
... According to the applicable regulations of the Mines and Works Act or the Machinery and Occupational Safety ...
Reliability Maintenance Concerns
... of the same type and rating maintains the original design integrity. Mechanical Device Testing and Maintenance An unfortunate but common practice in the industry is to install an electrical distribution system with circuit breakers and ignore the required testing and maintenance. This is often true ...
... of the same type and rating maintains the original design integrity. Mechanical Device Testing and Maintenance An unfortunate but common practice in the industry is to install an electrical distribution system with circuit breakers and ignore the required testing and maintenance. This is often true ...
Benefits derived from the FF specification FF-831
... describes tests and measurement procedures for Foundation Fieldbus power supplies and conditioners. FF-831 is based on the existing physical layer specifications IEC 61158-2: 2003, FF-830 1.5 and FF-816 1.5, but considers tests beyond the requirements of these standards that determine if the power s ...
... describes tests and measurement procedures for Foundation Fieldbus power supplies and conditioners. FF-831 is based on the existing physical layer specifications IEC 61158-2: 2003, FF-830 1.5 and FF-816 1.5, but considers tests beyond the requirements of these standards that determine if the power s ...
Different leakage Current
... The Alternative Method is in effect similar to testing the leakage current to IEC 60601 whilst measuring with the Open Neutral single fault condition in both polarities at once. Other comparison can be made with the Insulation test method (except, we do not measure resistance at a DC voltage but lea ...
... The Alternative Method is in effect similar to testing the leakage current to IEC 60601 whilst measuring with the Open Neutral single fault condition in both polarities at once. Other comparison can be made with the Insulation test method (except, we do not measure resistance at a DC voltage but lea ...
Automatic test equipment
Automatic or automated test equipment (ATE) is any apparatus that performs tests on a device, known as the Device Under Test (DUT), Equipment Under Test (EUT) or Unit Under Test (UUT), using automation to quickly perform measurements and evaluate the test results. An ATE can be a simple computer controlled digital multimeter, or a complicated system containing dozens of complex test instruments (real or simulated electronic test equipment) capable of automatically testing and diagnosing faults in sophisticated electronic packaged parts or on Wafer testing, including System-On-Chips and Integrated circuits.