Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
TechnicalInformation 2PS24017E3CE32778 PrimeSTACK™ Preliminarydata Keydata 1x1300Apeakat1225VDC,naturalair(freeconvection) Generalinformation Stacksforvariousinverterapplication.IGBT's,heatsinks,driversandsensorsincluded Topology 1/2 B2I BDTIC Application / Modulation Brake Chopper / Rectangle Load type resistive Cooling natural air (free convection) Market common industrial, drives, power supply Implemented sensors current, temperature Semicond. (Unit 1) none DC Link 1.4mF Semicond. (Unit 2) none Semicond. (Unit 3) IGBT 8x FF300R17KE3 Driver signals IGBT optical HFBR-15X1 / HFBR-25X1 Standards EN50178, UL94, prepared for UL508C Internal ID 32778 Mechanical drawing number 32778_MB Electrical drawing number 2PS-CC-V-OEA-Rev01 Dimensions (width x depth x height) 394 mm x 370 mm x 270 mm Weight 30 kg preparedby:OW dateofpublication:2012-11-23 approvedby:SD revision:2.2 www.BDTIC.com/infineon 1 TechnicalInformation 2PS24017E3CE32778 PrimeSTACK™ Preliminarydata Note Electricaldata DCLink Voltage min typ max units 1150 1250 V min typ max units V VDC Unit3DC(Chopper,Stepup,Stepdown) Chopper voltage on depending on controller VUnit3 on 1250 Chopper voltage off depending on controller VUnit3 off 1225 V BDTIC Load resistor RLoad Short time current Tinlet = 40°C, 10s, every 3600s, initial load = 0Aavg IUnit3 Overcurrent shutdown Within 15µs Power losses VUnit3 = 1225V, Tinlet = 40°C, Tj = 125, fsw3 = 500Hz, IUnit3 = 1300Aavg Ploss3 Generaldata Power losses (PCB) EMC test according to IEC61800-3 at named interfaces 1300 Aavg 3720 Apeak 3000 W min typ max units 50 W Ploss aux power VBurst 2 kV control VBurst 1 kV aux (24V) VSurge 1 kV Insulation management is designed for VLine Insulation test voltage according to EN50178, f = 50Hz, t = 60s Visol Importantcomponentdata 690 min max 1,40 type Temperature range typ VRMS kVRMS 2,5 CDC DC Link capacitor Ω 0,94 units mF Foil -25 +70 °C Rated voltage per device UR 1500 VDC Rated capacitance per device CR 350 µF Capacitance tolerance per device Tol Maximum ripple current per device, Tamb = 60°C IRmax wiring system series,parallel Balance or discharge resistors per DC Link unit dateofpublication:2012-11-23 approvedby:SD revision:2.2 +10 % 60 ARMS 1s, 4p Rb Setting of Active Clamping TVS Diodes preparedby:OW -10 Vz www.BDTIC.com/infineon 2 82,0 1280 kΩ V TechnicalInformation 2PS24017E3CE32778 PrimeSTACK™ Preliminarydata Controllerinterfacedata min typ max units 18 24 30 Vav Auxiliary voltage Vaux Auxiliary power requirement Vaux = 24Vav Paux 40 Driver and interface board see separate technical information DR240 Driver core EiceDRIVER 2ED300C17-S Digital input level resistor to GND 10,0kΩ, capacitor to GND 1nF, high = on, min 15mA Digital output level open collector, low = ok, max 15mA Analog current outputs Unit 2 load max 1mA; Vana out load max 1mA; at 1300A Vana out Analog current outputs Unit 3 Vin 0,0 Vout 0,0 15,0 30,0 W V V 3,60 3,50 3,60 V 3,70 V BDTIC Analog temperature output load max 1mA; at TNTC = 80°C correspond to Tj = 125°C VT out 9,60 9,80 10,00 V Overtemperature shutdown at TNTC = 80°C correspond to Tj = 125°C Overcurrent shutdown reaction time VT out OT 9,8 V afterovercurrentmessagebyPrimeSTACK™interface 10 µs Optical interface board see separate technical information Optical input power 12 µW Optical output power 60 µW preparedby:OW dateofpublication:2012-11-23 approvedby:SD revision:2.2 www.BDTIC.com/infineon 3 OEA240 TechnicalInformation 2PS24017E3CE32778 PrimeSTACK™ Preliminarydata IGBTdataunit3 min Type assumed collector-emitter saturation voltage Ic = 300A; Vge = 15V; Tvj = 125°C parameter for linear model Tvj = 25°C parameter for linear model parameter for linear model parameter for linear model typ max units VCE sat 2,4 V Vce1 1,025 V Tvj = 25°C rce1 3,25 mΩ Tvj = 125°C Vce2 0,975 V Tvj = 125°C rce2 4,75 mΩ mJ turn-on / turn-off energy loss per pulse Tvj = 25°C E1 71 / 64 turn-on / turn-off energy loss per pulse Tvj = 125°C E2 105 / 94 mJ thermal resistance, junction to case per IGBT Rthjc 0,085 K/W thermal resistance, case to heatsink per IGBT Rthch 0,033 K/W min typ max Type assumed forward voltage IF = 300A; Vge = 0V; Tvj = 125°C VF parameter for linear model Tvj = 25°C parameter for linear model Tvj = 25°C parameter for linear model Tvj = 125°C parameter for linear model Tvj = 125°C reverse recovery energy reverse recovery energy BDTIC Diodedataunit3 units 1,9 VF1 1,035 V rF1 2,55 mΩ VF2 0,925 V rF2 3,25 mΩ Tvj = 25°C Erec1 40 mJ Tvj = 125°C Erec2 72 mJ thermal resistance, junction to case per Diode Rthjc 0,13 K/W thermal resistance, case to heatsink per Diode Rthch 0,051 K/W units Environmentalconditions V min typ max Storage temperature Tstor -40 85 °C Ambient temperature minimum 0°C for optional optical interface Tamb -25 55 °C Operating temperature see chapter Heat sink air cooled / Thermal data Cooling air velocity (PCB) VAir PCB 2,0 m/s Air pressure standard atmosphere Humidity no condensation Installation height Vibration pAir 900 1100 hPa Rel. F 5 85 % 0 1000 m according to IEC60721 5 m/s² Shock according to IEC60721 40 Protection degree Pollution degree Torque at DC Terminals MDC 6,0 Torque at AC Terminals MAC Dimensions width × depth × height Weight with heat sink approximation preparedby:OW dateofpublication:2012-11-23 approvedby:SD revision:2.2 2 10,0 16,0 20,0 Nm 394 370 270 mm 30,0 kg www.BDTIC.com/infineon 4 m/s² IP00 Nm TechnicalInformation PrimeSTACK™ 2PS24017E3CE32778 Preliminarydata Mechanicaldrawing BDTIC preparedby:OW dateofpublication:2012-11-23 approvedby:SD revision:2.2 www.BDTIC.com/infineon 5 TechnicalInformation 2PS24017E3CE32778 PrimeSTACK™ Preliminarydata Circuitdiagram BDTIC preparedby:OW dateofpublication:2012-11-23 approvedby:SD revision:2.2 www.BDTIC.com/infineon 6 TechnicalInformation 2PS24017E3CE32778 PrimeSTACK™ Preliminarydata Terms&Conditionsofusage Thedatacontainedinthisproductdatasheetisexclusivelyintendedfortechnicallytrainedstaff.Youandyourtechnical departmentswillhavetoevaluatethesuitabilityoftheproductfortheintendedapplicationandthecompletenessoftheproduct datawithrespecttosuchapplication. Thisproductdatasheetisdescribingthecharacteristicsofthisproductforwhichawarrantyisgranted.Anysuchwarrantyis grantedexclusivelypursuantthetermsandconditionsofthesupplyagreement.Therewillbenoguaranteeofanykindforthe productanditscharacteristics. Shouldyourequireproductinformationinexcessofthedatagiveninthisproductdatasheetorwhichconcernsthespecific applicationofourproduct,pleasecontactthesalesoffice,whichisresponsibleforyou(seewww.infineon.com,sales&contact). Forthosethatarespecificallyinterestedwemayprovideapplicationnotes. BDTIC Duetotechnicalrequirementsourproductmaycontaindangeroussubstances.Forinformationonthetypesinquestionplease contactthesalesoffice,whichisresponsibleforyou. ShouldyouintendtousetheProductinaviationapplications,inhealthorliveendangeringorlifesupportapplications,please notify.Pleasenote,thatforanysuchapplicationsweurgentlyrecommend -toperformjointRiskandQualityAssessments; -theconclusionofQualityAgreements; -toestablishjointmeasuresofanongoingproductsurvey, andthatwemaymakedeliverydependedontherealization ofanysuchmeasures. Ifandtotheextentnecessary,pleaseforwardequivalentnoticestoyourcustomers. Changesofthisproductdatasheetarereserved. SafetyInstructions Priortoinstallationandoperation,allsafetynoticesandwarningsandallwarningsignsattachedtotheequipmenthavetobe carefullyread.Makesurethatallwarningsignsremaininalegibleconditionandthatmissingordamagedsignsarereplaced.To installationandoperation,allsafetynoticesandwarningsandallwarningsignsattachedtotheequipmenthavetobecarefully read.Makesurethatallwarningsignsremaininalegibleconditionandthatmissingordamagedsignsarereplaced. preparedby:OW dateofpublication:2012-11-23 approvedby:SD revision:2.2 www.BDTIC.com/infineon 7