* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Lecture Notes: Chapter 5 part 1
Pulse-width modulation wikipedia , lookup
Power inverter wikipedia , lookup
Immunity-aware programming wikipedia , lookup
Stepper motor wikipedia , lookup
Three-phase electric power wikipedia , lookup
Variable-frequency drive wikipedia , lookup
History of electric power transmission wikipedia , lookup
Electrical substation wikipedia , lookup
Electrical ballast wikipedia , lookup
Distribution management system wikipedia , lookup
Power electronics wikipedia , lookup
Schmitt trigger wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Surge protector wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Voltage regulator wikipedia , lookup
Alternating current wikipedia , lookup
Stray voltage wikipedia , lookup
Current source wikipedia , lookup
Buck converter wikipedia , lookup
Network analysis (electrical circuits) wikipedia , lookup
Voltage optimisation wikipedia , lookup
Mains electricity wikipedia , lookup
DMT 121 – ELECTRONIC DEVICES CHAPTER 5: FIELD-EFFECT TRANSISTOR (FET) 1 TYPES OF FET 1. 2. Junction Field-Effect Transistor (JFET) N-channel P-channel Metal Oxide Semiconductor FieldEffect Transistor (MOSFET) Enhancement-MOSFET Depletion-MOSFET 2 FET vs BJT FET Unipolar device – operate use only one type of charge carrier Voltage-controlled device – voltage between gate & source control the current through device. High input resistance BJT Bipolar device – operate use both electron & hole Slower in switching (turnon & off) Faster in switching (turnon & off) Current-controlled device – base current control the amount of collector current. High input impedance 3 THE JFET BJT – current controlled, IC is direct function of IB FET – voltage controlled, ID is a direct function of the voltage VGS applied to the input circuit. FIGURE: (a) Current-controlled and (b) voltage-controlled amplifiers. 4 JFET 3 terminal: Drain – upper end Source – lower end Gate – 2 p/n-type regions are diffuse in the n/p-type material to form a channel. FIGURE: A representation of the basic structure of the two types of JFET. 5 JFET Structures & Symbols JFET Structures JFET Symbols 6 Basic Operation of JFET VDD provides a drain-to-source voltage and supplies current from drain to source. VGG sets the reverse-bias voltage between gate and source. JFET is always operated with the gate-source pn junction reversebiased. Reverse-biased of gate-source junction with negative gate voltage produce a depletion region along pn junction – increase resistance by restricting the channel width 7 Basic Operation of JFET Figure: Greater VGG narrows Figure: Less VGG widens the the channel (between the channel (between the white white areas) which increases areas) which decreases the the resistance of the channel resistance of the channel and decreases ID. and increases ID. 8 Basic Operation of JFET The channel width and the channel resistance can be controlled by varying the gate voltage – controlling the amount of drain current, ID. The depletion region (white area) created by reverse bias. Wider toward the drain-end of the channel – reversebias voltage between gate and drain is greater than voltage between gate and source. 9 JFET Analogy JFET operation can be compared to a water spigot. The source of water pressure is the accumulation of electrons at the negative pole of the drain-source voltage. The drain of water is the electron deficiency (or holes) at the positive pole of the applied voltage. The control of flow of water is the gate voltage that controls the width of the n-channel and, therefore, the flow of charges from source to drain. 10 JFET Characteristic Figure: JFET with VGS=0 V and variable VDS (VDD) Figure: Drain Characteristic 11 JFET Characteristics and Parameters, VGS = 0 VGS = 0 V by shorting the gate to source (both grounded). ID increases proportionally with increases of VDD (VDS increases as VDD is increased). This is called the ohmic region (point A to B). In this area (ohmic region) the channel resistance is essentially constant because of the depletion region is not large enough to have sufficient effect VDS and ID are related by Ohm’s law In JFET, IG = 0 an important characteristic for JFET 12 JFET Characteristics and Parameters, VGS = 0 At point B, the curve levels off and enter the active region where ID constant. Value of VDS at which ID becomes constant is pinch-off voltage, VP. As VDD increase from point B to point C, the reverse-bias voltage from gate to drain (VGD) produces a depletion region large enough to offset the increase in VDS, thus keeping ID relatively constant. VDS increase above VP, produce almost constant ID called IDSS. IDSS (drain to source current with gate shorted) is max drain current at VGS = 0V 13 JFET Characteristics and Parameters, VGS = 0 • Breakdown occurs at point C when ID begins to increase very rapidly with any further increase in VDS. • It can result irreversible damage to the device • So JFETs are always operated below breakdown and within the constantcurrent area (between points B and C on the graph) 14 VGS controls ID 15 VGS controls ID As VGS is set to increasingly more negative by adjusting VGG. A family of drain characteristic curves is produced. Notice that ID decrease as the magnitude of VGS is increased to larger negative value narrowing of channel. For each increase in VGS, the JFET reaches pinchoff (constant current begins) at values of VDS less than VP. The amount of drain current is controlled by VGS. 16 Cutoff Voltage Value of VGS that makes ID ≈ 0A is the cutoff voltage, VGS(off). JFET must operated between VGS=0V and VGS(off). In n-channel JFET: VGS has large –ve value, ID is reduce to zero. Cutoff effect due to widening of depletion region. 17 VGS controls ID 18 Pinch-Off & Cutoff Voltage Pinch-off voltage, VP = value of VDS at which drain current becomes constant and equal to IDSS at VGS = 0V Pinch-off occurs for VDS value less than VP when VGS is nonzero. VGS(off) & VP are equal in magnitude but opposite sign VGS(off) = -VP 19 P-channel JFET operation Same as n-channel JFET except required negative VDD and positive VGS. 20 EXAMPLE VGS(off)= -4V and IDSS= 12mA. Determine the minimum value of VDD required to put the device in constantcurrent region of operation when VGS= 0V. 21 JFET Transfer Characteristic 22 JFET Transfer Characteristic The transfer characteristic of input-to-output is not as straightforward in a JFET as it is in a BJT. In a BJT, indicates the relationship between IB (input) and IC (output). Control Variable IC = IB constant In a JFET, the relationship of VGS (input) and ID (output) is a little more complicated: V I D I DSS 1 GS V P Constant 2 Control Variable 23 JFET Transfer Curve This graph shows the value of ID for a given value of VGS. When VGS = 0; ID = IDSS When VGS = VGS (off) = VP; ID = 0 mA 24 Plotting JFET Transfer Curve Step 1 Solving for VGS = 0V V I D I DSS 1 GS VP ID = IDSS Step 2 2 V I D I DSS 1 GS VP Solving for VGS = Vp (VGS(off)) ID = 0A 2 Step 3 Solving for VGS = 0V to Vp V I D I DSS 1 GS VP 25 2 EXAMPLE JFET with IDSS = 9 mA and VGS(off) = -8V (max). Determine ID for VGS = 0V, -1V and -4V. ANSWER: VGS = 0V, ID = 9mA VGS = -1V, ID = 6.89mA VGS = -4V, ID = 2.25mA 26 JFET Biasing Just as we learned that the bipolar junction transistor must be biased for proper operation, the JFET too must be biased for operation. Let’s look at some of the methods for biasing JFETs. In most cases the ideal Qpoint will be the middle of the transfer characteristic curve which is about half of the IDSS. JFET ID IDSS (1 I D = IS IG 0 A VGS 2 ) VP BJT IC = IB IC IE VBE 0.7 V 27 JFET Biasing JFET must be operated that gate-source junction is always reverse-biased. VG=0V 28 Self-Bias Since VG = 0V, IG = 0A IS = ID VS = IDRS VGS = VG – VS = 0 – IDRS = -IDRS VD = VDD – IDRD VDS = VD – VS = VDD – ID(RD + RS) 29 JFET Biasing, Fixed- Bias Configuration IG = 0 so VRG = IGRG = (0 A)RG = 0 then RG can be removed from the circuit. RG only need in ac analysis through the input Vi - VGG – VGS = 0 VGS = - VGG 30 JFET Biasing, Fixed- Bias Configuration Drain-to-source voltage can be determined by applying Kirchoff’s voltage law VDS + IDRD –VDD = 0 VDS = VDD – IDRD Source voltage to ground; VS = 0 Drain-to-source voltage can also be determined through; VDS = VD – VS but VS = 0 then VDS = VD Fig. 7.5 Measuring the quiescent values of ID and VGS. Gate-to-source voltage VGS = VG – VS ; since VS = 0 VGS = VG Since the configuration requires two dc supply, its use is limited and not included in the list of common FET configurations. 31 JFET Biasing, Self- Bias Configuration Most common type of JFET bias. Eliminates the need for two dc supplies. The controlling gate-to-source is determined by the voltage across a resistor RS. For analysis, resistor RG replaced by a short circuit equivalent since IG = 0 A. 32 JFET Biasing, Self- Bias Configuration Voltage drop across source resistor, RS VRS = ISRS; since IS = ID then VRS = IDRS For indicated closed loop in the Figure 7.9 -VGS – VRS = 0 VGS = - VRS VGS = -IDRS Drain current, ID: Fig. 7.9 DC analysis of the self-bias configuration. I D I DSS (1 VGS 2 ) VP I D I DSS (1 I D RS 2 ) VP I D I DSS (1 I D RS 2 ) VP 33 JFET Biasing, Self- Bias Configuration Voltage between drain-to-source, VDS VDD – IDRD – VDS – ISRS = 0 Since IS = ID VDD – IDRD – VDS – IDRS = 0 VDS = VDD – ID(RD + RS) OR VDS = VD – VS VS = ISRS and VD = VDD – IDRD Fig. 7.9 DC analysis of the self-bias configuration. Voltage between gate-to-source, VGS VGS = VG – VS; Since VG = 0 VGS = -VS and VS = ISRS Then VGS = - ISRS 34 JFET Biasing, Self- Bias Configuration The value of RS needed to establish the computed VGS can be determined by the previously discussed relationship below. RS = | VGS/ID | The value of RD needed can be determined by taking half of VDD and dividing it by ID. RD = (VDD/2)/ID 35 JFET Biasing, Self- Bias Configuration Remember the purpose of biasing is to set a point of operation (Qpoint). In a self-biasing type JFET circuit the Q-point is determined by the given parameters of the JFET itself and values of RS and RD. Setting it at midpoint on the drain curve is most common. One thing not mentioned in the discussion was RG. It’s value is arbitrary but it should be large enough to keep the input resistance high. 36 JFET Biasing, Voltage-Divider Configuration The basic construction exactly the same with BJT, but the dc analysis quite different with IG = 0 for FET The voltage at source, VS must be more positive than the voltage at the gate, VG in order to keep gatesource junction reverse-biased. 37 JFET Biasing, Voltage-Divider Configuration Gate-to-source analysis VG ( R2 )VDD R1 R2 VS = IDRS Gate-to-source voltage; VGS = VG – VS And source voltage is VS = VG – VGS The drain current can be expressed as ID VS VG VGS RS RS 38 JFET Biasing, Voltage-Divider Configuration Drain-to-source analysis VDS = VDD – ID(RD + RS) VD = VDD – IDRD VS = IDRS I R1 I R 2 VDD R1 R2 39