Download ZODIAC DATA SYSTEMS

ZODIAC DATA SYSTEMS
ZODIAC AIRCRAFT SYSTEMS
HEIM DATaRec® 4 series
Technical Specifications
DIC24 DC
The DIC24 DC module can record 24 analog channels (up to 24 x
20 kHz analog bandwidth, maximum sampling rate is 50 kHz; all
24 channels must have the same bandwidth).
Total Harmonic Distortion (THD)≤-100 dB, typ. <-108 dB at 2
Vpeak Range, 32 bit mode, Signal
1 kHz Sine -1 dBFS, 24 °C
Spurious-Free Dynamic Range (SFDR)
incl. Harmonics
DIC24 DC (HS310-0125)
≥100 dB, typ. >110 dB at 2 Vpeak
Range, 32 bit mode, Signal 1 kHz
Sine -1 dBFS, 24 °C
24-Channel Voltage Module (single ended)
Number of channels
24
excl. Harmonics
Operating mode
Record (no E to E)
Input signal
Single ended analog voltage
≥120 dB, typ. >124 dB at 2 Vpeak
Range, 32 bit mode, Signal 1 kHz
Sine -1 dBFS, 24 °C
Sampling frequency (Fs)
100 Hz to 50 kHz, settable in
steps of 1 Hz (For use in a Link
chain configuration the sampling
frequency must be a binary
divider of the overall system Fs)
Connector
Analog input: 1 * 50 pin D-Sub
Functions
Sampling ratio
2.5; no mirroring effect
Integrated calibration unit
1 ppm reference calibration
Analog bandwidth
Max. 20 kHz (settable)
Galvanic isolation
Resolution
16 bit/32 bit
Input signal range
± 10 mVpeak to ± 10 Vpeak
(settable in steps)
Between analog and digital layer
inside of the module and between
modules
Max. isolation voltages
Power input to digital part: 48 V
DC accuracy
± 0.1 % or ± 1 mV
Signal coupling
DC
Input impedance
Power input to analog part: 48 V
Digital part to analog part: 48 V
Input channel voltage safety
1 MΩ
± 35 V
Phase accuracy between two modules
≤ 0.3° by same sampling
frequency and until 20 kHz
bandwidth
≤ 1° by different sampling
frequency
Phase accuracy
≤ 0.2°
Analog to digital converter
24 bit
Signal to Noise Ratio (SNR)
≥92 dB, typ. >98 dB at 2 Vpeak
Range, 32 bit mode, Signal 1 kHz
Sine -1 dBFS, 24 °C
© ZODIAC Data Systems GmbH
Page 1 of 2
Document No.: TS_DIC24_DC_140401_HD5431041R00616.fm
All trademarks acknowledged. ZODIAC Data Systems GmbH reserves the right to amend these specifications without notice.
HEIM DATaRec® 4 series
Technical Specifications
DIC24 DC
Additional Infos
Synchronicity of samples
Environmental specifications
In a Link chain configuration with
several analog modules the
sample synchronicity of all
modules depends on the
sampling frequencies of each
module. For sample synchronicity
the module sampling frequency
must be a multiplier of 2 to the
power of n (Fs x 2n; n = wholenumbered) of each other module
sampling frequency.
Example: One module sampling
frequency (Fs) = 4kHz. Sampling
frequency of all other modules
must be one of the following: 4kHz
x 20 (= 4kHz), 4kHz x 21 (= 8kHz),
4kHz x 22 (= 16kHz), 4kHz x 23
(= 32kHz), 4kHz x 24 (= 64kHz),
and so on; or 4kHz x 2-1 (= 2kHz),
4kHz x 2-2 (= 1kHz), 4kHz x 2-3
(= 0.5kHz), 4kHz x 2-4
(= 0.25kHz), and so on.
General
Dimensions
Vibration
5g
Shock
10 g
Temperature
According to standard
IEC 60068-2-14-Nb
Operation as standalone
-20 °C ...+70 °C
-30 °C ...+70 °C
Special start-up procedure required
Operation in a Link chain
-10 °C ...+55 °C
-20 °C ...+55 °C
Special start-up procedure required
Storage
-40 °C ...+85 °C
Humidity
0 ...93% relative, non-condensing
EMI
DIN EN61000-6-4 / DIN
EN61326-1
For operation in industrial environment
(according to DIN EN 61326) earthing
of the module and / or shielded cable
is necessary to prevent influences by
external electromagnetic distortions
Notes
Standard HEIM DATaRec 4
housing. 48.1 x 184 x 124.5 mm
(w x h x d) including fixing system
Performance varies depending on the installation environment.
The shown values were measured using an appropriately designed test system including the HEIM DATaRec® 4 power supplies under nominal conditions of temperature, voltage, etc..
Weight
1100 g typical
Cooling
Conduction cooled
Power consumption
15 W typical
Performance is significantly influenced by storage medium type,
host computer performance and load, used acquisition software,
signal module configuration, power supplies and cabling.
Power input range
17 ...28 V DC (via appropriate
DATaRec® 4 System Power
Module)
Definitions
Specifications with limiting symbols (<, >, ≤, ≥, ±, min, max, etc.) or
a bandwith (x ...y) represent performance within a range of values.
Input DC power
Low power detection
Communication
HeimLink, USB 2.0 and RS232;
Display, Button, LED.
Specifications named as „typical“ represent performance met by
approximately more than 80% of the specification basis (channels,
produced devices, etc.).
Specifications without limits are nominal values or values within
standard tolerances (e. g. dimensions, sampling rates etc.).
ZODIAC Data Systems GmbH
Friedrich-Ebert-Strasse / TechnologiePark – D-51429 Bergisch Gladbach
Tel.: +49 2204 84 41 00 – Fax: +49 2204 84 41 99
[email protected] – http://www.zodiac-data-systems.com
© ZODIAC Data Systems GmbH
Page 2 of 2
Document No.: TS_DIC24_DC_140401_HD5431041R00616.fm
All trademarks acknowledged. ZODIAC Data Systems GmbH reserves the right to amend these specifications without notice.