Download General-Purpose Failsafe Moulded Wirewound Resistors

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Document related concepts

Standby power wikipedia, lookup

Power electronics wikipedia, lookup

Superconductivity wikipedia, lookup

Surge protector wikipedia, lookup

Printed circuit board wikipedia, lookup

Resistive opto-isolator wikipedia, lookup

Power MOSFET wikipedia, lookup

Switched-mode power supply wikipedia, lookup

Audio power wikipedia, lookup

Immunity-aware programming wikipedia, lookup

Rectiverter wikipedia, lookup

Thermal runaway wikipedia, lookup

PS Audio wikipedia, lookup

Surface-mount technology wikipedia, lookup

Lumped element model wikipedia, lookup

Ohm's law wikipedia, lookup

Transcript
General-Purpose Failsafe
Moulded Wirewound Resistors
Welwyn Components
SP20/SP20F Series
• Drop-in replacement for BW20/BW20F
• Predictable fusing characteristics
• 1 watt rated with 1/2 watt dimensions
• 0.1 ohm to 1200 ohms
• Weldable and solderable magnetic leads
Electrical Data
Type
SP20
SP20F
EIA RS-344 Style
CRU 1
MIL-R-11 Style
RC20/RC32
Resistance Range
ohms
Tolerance
0R1 to 1k2
0R1 to 1k
%
Power rating
±5, ±10
watts
1 at 50°C
1 at 50°C
0.75 at 70°C
0.75 at 70°C
0.5 at 100°C
-
Derating to 0 at 160°C
Derating to 0 at 160°C
√PR
Maximum continuous working voltage
Minimum insulation resistance
dry
10,000 Meg
wet
100 Meg
Minimum dielectric withstanding volts
ATM
700V
Reduced pressure
RMS
450V
Hotspot temperature rise
120°C at 1 watt
Current noise
Negligible
Physical Data
Dimensions (mm)
Type
L
D
d
f
SP20
9.91±0.25
3.56±0.20
0.813±0.05
38.1±3.2
SP20F
9.91±0.25
3.56±0.20
0.813±0.05
38.1±3.2
d
D
L
f
Resistive Element
Encapsulation
All resistor types have resistance alloy winding on a braided
fibreglass substrate. Intermediate silicone coatings are used to
enhance processibility and to provide protection to the
resistive element.
The SP20 and SP20F are encapsulated utilizing a compression
molded phenolic plastic material. The SP20F has a flame
resistance coating applied over the resistive element to
provide flammmability protection when destructive overloads
may occur.
Termination
The SP20 and SP20F resistors are terminated using an alloy
coated copper flashed steel lead welded to a cap of the same
material. This termination assembly is mechanically crimped,
utilizing an improved crimp design, to the resistive element.
Marking
All products are marked utilizing heat and solvent resistant
colour code bands consistent with EIA/MIL requirements. The
first band is double width to designate wirewound
construction. A fifth band, blue in colour, is used for
flameproof identification.
General Note
Welwyn Components reserves the right to make changes in product specification without notice or liability.
All information is subject to Welwyn’s own data and is considered accurate at time of going to print.
A subsidiary of
TT electronics plc
© Welwyn Components Limited · Bedlington, Northumberland NE22 7AA, UK
Telephone: +44 (0) 1670 822181 · Facsimile: +44 (0) 1670 829465 · Email: [email protected] · Website: www.welwyn-tt.com
Issue B · 03.02
95
General-Purpose Failsafe
Moulded Wirewound Resistors
Welwyn Components
SP20/SP20F Series
Performance Data
Test
Temperature coefficient (ppm)
ppm/°C
SP20
SP20F
<1R ±800
<1R ±800*
≥1R ±150
Dielectric withstanding voltage
≥1R ±150
RMS
Momentary overload
700V
%
5
Low temperature operation
%
5
Temperature cycle
%
5
Humidity
%
5
Load life
%
5
Terminal strength
%
5
Resistance to solder heat
%
5
*0.1 ohm SP20F <1000 ppm.
SP20 Power Derating
SP20F Power Derating
2.5
Power (watts)
Power (watts)
2.0
1.5
1.0
0.5
0
0
50
100
150
200
Ambient Temperature (°C)
Ambient Temperature (°C)
0.1 ohm
1 ohm
10 ohm
100 ohm
1000 ohm
Time (seconds)
Temp (°C)
SP20 and SP20F Temperature Rise
Power (watts)
SP20F Typical Fusing
Power Input (watts)
Ordering Procedure
Example: SP20F at 470 ohms and 5% tolerance tape packed on a reel of 4000 pieces –
SP20F – 470R J I
Type
Value (use IEC62 code)
Tolerance (use IEC62 code)
J
5%
Packing
I
K
Tape
10%
4000/reel
Standard
© Welwyn Components Limited Bedlington, Northumberland NE22 7AA, UK
Telephone: +44 (0) 1670 822181 · Facsimile: +44 (0) 1670 829465 · Email: [email protected] · Website: www.welwyn-tt.com
96
Issue B · 03.02