Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
WEC REGIONAL ENERGY FORUM – FOREN 2008 Neptun, 15-19 June 2008 SERB-SITON SOLUTION FOR THE SEISMIC ISOLATION OF A CANDU PHWR 700 NPP AND AN ACR 1000 NPP Authors: Viorel Serban, Adrian Panait, Marian Androne, George Alexandru Ciocan, Ioana Florea - SITON Subsidiary of Technology and Engineering for Nuclear Projects Abstract The paper is a presentation of a solution for the seismic isolation of nuclear objectives employing new SERB 800x800 devices developed by SITON. SERB 800x800 devices can overtake permanent compression loads (up to 6000 KN) over which dynamic compression and thrust loads up to 1500 KN may overlap. On vertical direction, the devices have a very high stiffness in order to avoid the occurrence of different settlements that may lead to additional loads in the isolated supra-structure. On horizontal plane, the devices are sliding with a very low friction ratio (ranging between 0.03 – 0.08) allowing displacements up to ± 225 mm while limiting the range through a non-linear stiffness which starts operating after 2/3 of the displacement has consumed. The advantages of the seismic isolation nuclear objectives are presented for one PHWR 700 NPP standard unit but the solution may also be applied to any type of nuclear power plant. 1. Introduction A method to increase the safety margin of nuclear objectives during an earthquake is their seismic isolation. For example, with CANDU PHWR and ACR type Nuclear Power Plants (NPP) the nuclear part or only the Reactor Building (R/B) or Spent Fuel Bay Building (SFB) may be isolated. The paper presents the advantages and disadvantages of SERB-SITON solution for the seismic isolation of the reactor building (R/B) and spent fuel bay building (SFB) for a site similar to Cernavoda Site. For to substantiate the seismic isolation solution this document presents alternative analyses regarding the seismic behavior of isolated buildings considering, for the seismic action, the design response spectrum typical for Cernavoda NPP and the sinusoidal type time history amplitude accelerations and repetition periods equivalent to the design seismic movement. The analyses of the alternatives have considered two modes of the isolation system behavior: oscillating system and quasi-oscillating system, also taking into account the Colombian type gliding dynamic friction. 2. Description of structures. – Reactor Building (R/B) The Reactor Building is a reinforced and prestressed concrete structure consisting of the containment and the inner structures supported on the base slab. The inner structures are made of 3 sub-structures: calandria vault, fuel transfer structure and the inner structure itself. The Containment Building (Fig 1) is a prestressed concrete structure, cylindrical in shape, with two domes on top. Its diameter is 41.5 m, the wall thickness is 1.57 m and the high is about 52 m. The clearance between the two spherical domes is filled in with cooling water. The Reactor Building inner structures are made of thick reinforced concrete walls arranged as per axes A.B.C.D and E (on B-D direction ) and axes 21,22,23,26 ( on A-C direction), four(4) reinforced concrete floors at El. 100,107,112,117, a base slab and sub-base between El. 88,7 m and El.93.9 m (Fig 2). The base of the Reactor Building foundation is located at about 88.7 m (4.78 NMB). 1 WEC REGIONAL ENERGY FORUM – FOREN 2008 Neptun, 15-19 June 2008 The Reactor Building weight is about 880000 KN out of which the sub base-base slab represents 240000Kn. Besides its function to provide the climatic protection of the systems, equipment and operation personnel in case of a coolant loss (Design Base Accident-DBA), the containment is also providing the essential function of retaining the accidental radioactive releases from the process systems and equipment in various emergency cases, including DBA, since the containment is a special protection measure for the population and the environment. The Containment is designed to withstand and maintain its tightness degree at a pressure resulted from a Design Base Accident (DBA) with the Dousing System in service. The Containment is also designed to maintain its integrity and tightness at a DBE earthquake. For to provide the tightness, the inner side of the containment wall is epoxy lined. 23 A 21 D 1 24 3. 25 22 26 27 B C Cernavoda NPP - Traditional seismic qualification. R018 2 For to overtake in safe conditions, the seismic loads generated by earthquakes likely to occur on Cernavoda Site and having accelerations smaller or equal to a DBE (0.2 g on any direction in horizontal plane), the buildings, equipment , piping systems, etc. were Fig. 1. Reactor Bldg. General View Fig. 2. Reactor Bldg. Cross-Section. El.93 differently sized as per the type of structure and material so that the total stresses resulted from the groups of loads including an earthquake, should not exceed the stresses associated to the yielding strength of the ductile materials and cracking should not occur with brittle materials. R006 17 R010 ER 19 14 18 R014 R004 R008 DR R109 R001 R017 R012 CR 9 R011 8 BR R003 12 R007 7 13 6 10 R013 5 11 Emergency Airlock 3 14 15 AR 4 16 R005 R009 10 11 12 13 14 15 16 17 18 19 Bazin stropire Armături sistem de stropire Pompă moderator Schimbător căldură moderator Cabineţi izolare fideri Faţa reactorului Reactor Mecanisme reactivitate Pompă circuit primar Pod MID 1 2 3 4 5 6 7 8 9 Cărucior MID Ansamblu Catenaria MID Poziţie întreţinere MID Uşa camera MID Rezervor întârziere sistem răcire protecţie biologică Răcire cheson calandria Presurizor Generator abur Pod rulant generator abur The stress and distortion condition in buildings, equipment and components of the Plant were determined with detailed dynamic models in which the possibility of amplifying the dynamic response of the analyzed system due to the kinetic and potential energy built-up during a seismic movement, was considered. The traditional seismic qualification of CANDU type NPPs is based on the concept of minimizing the amplification of the seismic response of buildings, equipment, piping systems, etc. by stiffening them within the allowable technical limits. 4. Seismic isolation of R/B and SFB The solution is recommended to be applied to new NPPs. With CANDU type NPPs, the solution consists in the elimination of the sub-base, of the radial, central and peripheric keys between the base slab and sub-base as well as of the membrane between the base slab and sub-base. The R/B is supported on 270 isolators (SERB 800x800 type fig. 3-4) installed between the base slab and a reinforced concrete plate. Since between the R/B and SFB building there are technological connections required by the fuel channel transfer and the equipment and material airlock support, the seismic isolation system must be so constructed to provide the connection to R/B and allow for no relative movement during an earthquake, a relative movement that might negatively affect the fuel channel transfer and the equipment and material airlock. The SFB building shall rest on 40 isolators. Fig. 5-6 illustrates an alternative for the installation of SERB 800 x 800 isolation devices beneath the R/B and SFB building and of SERB –B-204 telescopic devices (1, 2, 8). Considering that with the building isolated solution the seismic loads on R/B and SFB building (including sites with high seismicity), are small, the proposal consists in the analysis of the 2 WEC REGIONAL ENERGY FORUM – FOREN 2008 Neptun, 15-19 June 2008 solution to raise the foundation elevation from El. + 80.75 by about 5 m while correspondingly modifying the technologic connections between the R/B, Service Building (S/B0 and Nuclear Auxiliary Building. Fig. 3. SERB 800 x 800 prototype. 0 and 150mm displacement Fig. 4. Experimental hysteresis characteristic In case the ground structure at the new foundation elevation allows the overtaking of permanent loads and seismic loads with the isolated solution, the only problem detrimental to the raise of the foundation elevation, is represented by the pressure losses along the live steam, supply water and condensate return piping. Bearing in mind that the pressure losses along these pipes, is increasing by maximum 5%, such a loss is not causing a major quantifying power loss in the steam turbine and practically, neither an additional power supply to the circulating water pumps. 5. Advantages and disadvantages of the R/B and SFB Bldg. seismic isolation. 5.1 Overall advantages 1. The reduction of the seismic action applied to the building, equipment, piping systems, by about 4 times for equipment and piping systems located in the lower part of the building, and by up to 40 times for equipment and piping systems located on the upper part of the building in the case with the building isolated (compared with the unisolated building solution); 2. The reduction of the probability to \ radiologically pollute the environment due to the fact that the isolation system allows an efficient and direct (visual) monitoring of the R/B and SFB Bldg. foundations. 3. A better overtaking of the shocks generated by the impact with airplanes. 5.2 Advantages for the NPP – BOP (Civil Part). 1. The removal of a 3.68 m thickness from the reinforced concrete sub-base, of the radial and peripheric keys. The volume of concrete is reduced by about 8000 m3 and the quantity of rebars by about 360 tons. 2. The reduction of the sectional seismic stress in the R/B and SFB structure by 5-10 times allowing thus a reduction of the reinforcement material by at least 15%. Such a reduction is benefic both in point of material savings ( by about 592 tons) and in point of facilitating and improving the quality of the reinforced concrete structure ( i.e today, due to the large number of reinforcing bars a compact concrete pouring is difficult and segregation and cavities in the reinforced concrete structures are produced). 3. The process of prestressing the perimetral wall and the containment base slab is facilitated and the time is shortened. The elimination of the membrane between the sub-base the base slab, of the central, peripheric and radial keys between the sub-base and the base slab. 4. The possibility to make a prestressed concrete infrastructure to the SFB Bldg will provide a very good waterproofing. In this case the inner lining of the SFB walls by stainless steel plates welded onto the supporting steel structure, is no longer required and the savings of material (stainless steel) is about 260 tons. 3 WEC REGIONAL ENERGY FORUM – FOREN 2008 Neptun, 15-19 June 2008 5.3 Advantages for the NPP – NSP (Process Part) 1. The reduction of the seismic action on the equipment and piping systems results in the elimination of the seismic qualification requirement for equipment and piping systems in the R/B and SFB Building. In other words such a reduction will represent at least 1% savings with the equipment purchase and the elimination of snubbers in the piping systems and equipment.- a total of 370 snubbers estimated to 3700000 Euro. In case that a decision is taken to keep on some steam generator snubbers for safety considerations, they may be substituted with smaller snubbers or other types of supports. 2. The overall reduction of the equipment cost is estimated to 1.72 million Euro considering that the cost of the installed equipment is about 172 million Euro for one CANDU PHWR 700MW unit. 5.4 Disadvantages of the isolation solution for NPP – Civil Part (BOP) 1. The construction of a full large excavation of about 1500 m3 than with the classic solution. 2. The construction of about 6800 m3 reinforced concrete poured in the base plate and the supporting wall and the stands for the isolation devices. The re-bars for reinforcing the concrete base plate and the supporting wall and the stands is estimated to amount 580 tons. 5.5 Disadvantages for the NPP Process Part (NSP). The seismic isolation of R/B and SFB Building will lead to a relative movement of maximum ±20 cm on any direction in horizontal plane between these buildings and the other buildings in the plant. In this case the connecting process piping of the steam circuit, supply water system, condensate return, emergency cooling water, etc need to be capable to overtake the relative movement between the isolated buildings and the un-isolated buildings in safe conditions. To overtake the seismic loads, the supports on R/B and S/B need to be so constructed to allow the relative movement in the horizontal plane coincident with the displacements from thermal expansions. The spatial development of the piping systems allow the overtaking of relative seismic displacements between the seismically isolated and unisolated buildings while SERB type supports can provide the overtaking of displacements from thermal expansions. The seismic isolation is not involving important modifications of the electric and I&C cable systems. The only modification consists in the extended length of such cables by about 0.5 m and the construction of some racks to allow ± 200 mm relative movements in horizontal plane. 6. Estimation of Costs related to the R/B and SFB seismic isolation. 1. The fulfillment of the R/B and SFB isolation system implies costs related to purchasing, amounting to about 7000 Euro/piece and to installation works amounting to 1000 Euro/piece. The total amount required would be 310 X 8000 Euro = 2480000 Euro. 2. The volume of poured concrete is reduced from 8000 m3 representing the eliminated 3.62 m thick sub-base, down to 6800 m3 representing the 1.6 m thick base plate – general base slab, the 0.5 m supporting wall and the isolation device stand. The savings in respect of concrete quantity is 1200 m3 amounting about 200 Euro/m3 X 1200 m3 = 240000 Euro. 3. The additional quantity of reinforcement required for to construct the base plate and the supporting wall is 580 tons – 380 tons = 280 tons representing an additional cost of 2000 Euro/ton X 200 tons = 400000 Euro. 4. The less quantity of reinforcement for R/b as a result of reducing the seismic loads is about 592 tons representing savings : 2000 Euro/ton X about 592 tons = 1184000 Euro. 5. The elimination of the snubbers on the live steam piping represents 3700000 Euro savings. 6. The reduction of costs associated to the equipment and system seismic qualification because of the reduction of the seismic accelerations is estimated to 1.72 million Euro. 4 WEC REGIONAL ENERGY FORUM – FOREN 2008 Neptun, 15-19 June 2008 The R/B and SFB seismic isolation by SERB-SITON solution involves an cost saveings of about 154000 Euro. In case that the solution to raise the R/B and SFB by 5 m is accepted, the isolation solution much less expensive than the classic solution. Note that the figures are for information only. 7. Description of the isolation solution. The R/B is a stiff structure made of prestressed reinforced concrete (the containment and the base slab) and unstressed concrete (inner structures and the sub-base). The SFB building is made of prestressed reinforced concrete and it is technologically connected to the R/B via the fuel transfer channel. In point of construction The R/B is not connected to S/B, Nuclear Auxilliary Bldg., and BOP but it is technologically connected via the live steam, supply water, emergency cooling water piping and electric and I&C cable systems. Also, for the equipment transfer, the R/B is provided with the equipment airlock that is supported on the concrete structure of the fuel transfer channels to the SFB and the personnel access the containment is provided with a personnel airlock supported on the building base slab. The spent fuel transfer from the R/B to the SFB is made via a technologic connection that must be tight, with zero water leakage from the fuel transfer channel. Between the two structures – R/B and SFB (fuel transfer channels)– there must be no relative movement greater than the elastic distortion in the joints between the two structures(buildings) so to prevent water leakage from the fuel transfer channel . The R/B seismic isolation need to be so done that the technological connections with the other buildings should not be affected. For that reason the R/B isolation (see Fig 4-5) is proposed to be as follows: 1. The construction of a general 1.6 m thick reinforced concrete sub-base embedded into the ground at El. + 88.75 m. The sub-base surface should be 32000 m2 spread beneath the R/B and SFB and to the outside with 1.0 m. In the area of SFB and R/B the sub-base is extended for to make connections between the base slab of the two buildings that provide a “zero” relative movement between the buildings and the fuel transfer channel. 2. The construction of a 0.5 m thick and 9.65 m high supporting wall on the sub-base boundary at El. + 90.35 m and El. + 100 m. 3. The construction of 310 square-shaped (1.5 m side X 1.0 m high) reinforced concrete stands to embed SERB 800 X 800 isolation devices. The distribution of shocks beneath the sub-base is so made that the R/B and SFB structure weight loads are quite uniformly distributed on SERB isolation devices. In the area associated to the R/B inner structures 136 stands are constructed, 138 stands for the perimetral wall area and 36 stands for SFB. 4. The installation of SERB 800 X 800 isolation devices on stands is made by 12 X M32 bolts in the embedded parts in the reinforced concrete stands. 5. The installation of the upper anchoring parts and their attachment to SERB 800 X 800 devices is made by 12 X M 32 bolts that are embedded in the reinforced concrete caps sized: 1.5m X 1.5 m X 0.4 m. 6. The construction of the R/B and SFB building base slab on the associated caps is made with no restraints in respect of the employed construction technology. 7. The construction of a connection between the R/B base slab and SFB base slab in the area of the fuel transfer channels for to avoid relative displacements between the two base slabs. The proposal is to construct 3 spatial metallic shaped connections of 2 X 2 m sizes in plane section. The R/B and SFB isolation employing SERB 800 X 800 devices offers the following advantages: 5 WEC REGIONAL ENERGY FORUM – FOREN 2008 Neptun, 15-19 June 2008 1. The possible seismic acceleration of R/B and SFB is ranging between 0.05 – 0.10 g for any earthquake irrespective of the ground acceleration if the ground seismic movement is smaller than ± 180 mm. If the ground seismic movements are greater than 180 mm (limits take in analyses), the seismic accelerations transferred to the buildings will exceed the above values dependant on the difference between the ground seismic movement and the relative distortion allowed by SERB devices; 2. The reduction of the reinforcement percentage in R/B and SFB, considering that the sectional seismic loads and stresses in the structural elements of R/B and SFB are reduced by at least 7 times, which allows a reduction of the reinforcement percentage and re-bars of at least 15% for a site with the ground maximum acceleration of 0.2 g for a DBE. 3. The elimination of the metal plates on the lower front side of the containment in the area of maximim seismic stress considering the low seismic stresses in the R/B containment with the isolation alternatives. 4. The elimination of the 6 mm thick stainless steel lining on the inner side of SFB because with the isolated solution the SFB may be constructed of post-stressed reinforced concrete which prevent the possibility of water leakage from the bay. The reduction of the number or even the elimination of snubbers on the live steam piping in R/B. All the equipment in R/B and SFB building need not be qualified at seismic accelerations and thus the cost is decreased by at least 5%. +100.00 +100.00 CONTRAFORT +93.83 +92.15 SUBRADIER +90.35 +88.75 Fig. 5. Isolators arrangement – R/B and SFB building Fig. 6. Detail on excavation and device installation. One SERB 800 X 800 device consists of a lower case and an upper case which are practically identical in point of construction and functionality. The two cases are interconnected by a central device offering relative independent movements between the two cases and elastic limiting and damping of the maximum displacement, at pre-set values. 8. Mathematical evaluation of the seismic isolation effects. According to the design standards, the seismic isolation principle assumes that the isolation system vibration period – isolated building, should be at least 3 times greater than the period of the building anchored at its base (embedded in the ground) for the building in the isolated solution, behave rigid versus the seismic movement(action) filtered by the seismic isolation system (3). Besides, for to protect the isolation device it is desirable that the device vibration period be at least 50% greater than the corner period ( Tc) of the response spectrum in the site area. In this case, dynamically speaking, the seismically isolated building will behave like a rigid body elastically supported and the relative displacement in the isolation devices will make the seismic energy be only partially transferred to the isolated building (5-6). 6 WEC REGIONAL ENERGY FORUM – FOREN 2008 Neptun, 15-19 June 2008 Fig. 7 illustrate the time history accelerations and specific response spectra of the absolute accelerations and the relative displacements associated to the time history accelerations for Cernavoda NPP Site. Fig. 7. Design time-history accelerations for Cernavoda NPP Site, response spectrum of accelerations for various damping and response spectrum of the relative displacements for various damping The establishment of the parameters for sizing the seismic isolation devices for buildings shall develop in two alternatives: Alternative 1 – The device with the isolated building make-up an oscillating system capable to accumulate kinetic energy for the building and the elastic potential in the isolation device generated by the seismic movement. In this case, the stiffness and damping of the isolation system (isolation device and limiting and reverting telescopic device) shall be evaluated so that the relative displacement in the system be maximum 18 cm (maximum allowable displacement in the SERB 800 X 800 isolation device prototype) for a ground acceleration of 0.2 g (maximum design acceleration at Cernavoda NPP) on a direction in the horizontal plane. Alternative 2 – The device with the isolated building make-up a quasi-oscillating system. The isolated building may move freely with friction on a distance imposed by the isolation system. After spending the free movement (between 1/2 and 2/3 of the maximum distance) the building is non-linear moved in order to limit its displacement and make it revert to the initial position. 8.1.1. Alternative 1 For analyses, the response spectrum of the relative displacements is used ( Fig. 8 calculated by SAP 2000 on basis of the design response spectrum of the accelerations). The horizontal line points out the maximum allowable relative displacement of the isolation device(0 = 18cm). The design criterium is that the relative displacement in the response spectrum be under the maximum design displacement, 0. Since the relative displacement depends on the eagen period of the isolation device – building assembly and the effective damping ratio, the analysis need to set-up optimum values for the eagen oscillation period and the damping ratio. The R/B isolation system is made by SERB 800 X 800 devices for to overtake the weight and by SERB –204 telescopic devices for the control of the building revert to the initial balance position. The actual viscous damping ratio, e,, is calculated considering the dynamic friction between the isolation element, , and the viscous damping of the elastic revert elements inside the isolation device and the telescopic devices for the R/B revert . The viscous damping energy and the energy due to friction , calculated for one oscillation cycle, is assimilated like the equivalent viscous damping energy on the same oscillation cycle : (mg 2mx)dx 2 mxdx e ciclu ciclu (1) it results: e e1 e 2 2g g (1 2 ) 2 (2) 0 0 where: = dynamic friction ratio between the gliding elements ( PTH on steel ~ 0.05-0.1.); = viscous damping ratio specific for the inner springs and telescopic elements, ~5% – 20%; 0= maximum design displacement 0 = 18cm; =maximum angular frequency of the ground seismic 7 WEC REGIONAL ENERGY FORUM – FOREN 2008 Neptun, 15-19 June 2008 movement 2 , Tc=0.7s, Tc [3]); ω = angular frequency of the R/B – isolation device 2 , Teff>2Tc=1.4s Teff Selecting a vibration period Teff ~ 3s for the isolation assembly, Fig 7 shows the result: the equivalent damping ratio need to be minimum e ~ 20%. That means a minimum friction ratio ~ 0.05 and minimum viscous damping ~ 5%, so, practically, any realistic range of damping/friction ratio. So, an equivalent high damping leads to the decrease of the response spectrum of the relative displacements, its value falling below the design displacement. The absolute acceleration of the mass becomes A = 0.84 m/s2 times below the ground maximum acceleration (Amax= 2m/s2). assembly The total estimated mass of the R/B including the inner structures, the containment and the base slab, is M= 63710 tons. The total number of isolation devices that support the R/B in the proposed isolated alternative is Nd= 270 isolation devices arranged beneath the containment perimetral wall and the inner structure walls and in their vicinity so that a relative uniform relief of the self-weight is obtained without generating large stresses in the base slab and walls. For to obtain a vibration period Teff 3s , the stiffness average value of a telescopic device shall be about keff = 20.6 for about 5% viscous damping (or greater) in function of the selected friction ratio so that the equivalent viscous damping ratio should not exceed 28%. 8.1.2. Alternative 2 In the beginning, consider that at the isolation interface, the building is moving with friction since the movement is not limited by elastic-with- damping devices. The aim is to estimate the nature of the system movement only under friction and displacement conditions. The law of movement is given by: x u g sign (x ) (3) where: x= relative displacement; x = relative velocity; u = ground acceleration; = friction ratio at the isolation interface. For the case of a sinusoidal acceleration time history of the ground movement having the amplitude : Ag = 2 m/s2 and fundamental period Ts= 1 s, the ground acceleration is 2 u(t ) Ag sin t (4) Ts In case of a null friction ratio, the building relative movement becomes equal and contrary to the ground movement and the total displacement is zero, the building staying at rest. Consequently the total acceleration is also null. In case of a friction ratio other than null, the building relative displacement is in anti-phase with the ground relative movement but it decreases and it is translated behind , proportionally with the value of the friction ratio. But the total displacement is increasing with the increase of the friction ratio but remains at small values for the usual ratios, = 0.05 – 0.1 (Fig 9). Calculated values of the building total acceleration gets values corresponding to friction a f g equal with 0.5 m/s2, 1.0 m/s2 respectively. Thus, for the isolation systems acting with gliding, without external forces (usually elastic forces) within a limited displacement range, the use of rather small friction ratio is maintaining the displacement at values smaller than the ground movement values. After an imposed movement, elastic forces may interfere meaning that, on one hand, they may limit the system gliding and, on the other, they may bring-back the system to its initial position. Such isolation solutions lead to the cutting-off of the acceleration response down to values corresponding to friction , a f g . 8 WEC REGIONAL ENERGY FORUM – FOREN 2008 Neptun, 15-19 June 2008 Relative Displacement Response Spectra for different damping ratio. 5% 10% 20% 30% 40% 50% S0 = 18 cm Relative Displacement Response Spectra, [cm] 60 50 40 30 20 10 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 Period T, [s] Fig. 8. Response spectrum of relative movements for different damping Fig. 9. In-time variation of the ground movement and response in relative and total movements under the action of a sinusoidal type acceleration, = 0.05, = 0.1 It is found that the maximum relative movement in case of a friction ratio = 0.05 – 0.1 is about 6 cm, much under the characteristic values an isolation device can have. For that reason, the radial telescopic devices arranged on the R/B base slab circumference having the rile to limit and revert, may have a special characteristic in which along a movement(displacement) of +/- 3-4 cm they do not act and than the stiffness of the devices is slowly increasing with the distortion. 8.2 Response of the system provided with non-linear telescopic devices and friction. A numerical estimation of the response of a system provided with a seismic isolation device with friction and a limiting and reverting telescopic device having a non-linear stiffness characteristic and viscous damping = 5% (damping considered constant) , was conducted. Fig. 11 illustrates the relative displacements of the system for the stiffness characteristic presented in Fig. 10. When friction is absent, the maximum relative displacement is limited to the 6 cm value (a little amplified as to the ground maximum movement of 5 cm) since the braces are slightly limiting the system relative displacement. Load-displacement characteristic Load Bilinear 1.3E+07 1.2E+07 1.0E+07 9.1E+06 Load, [N] 7.8E+06 6.5E+06 5.2E+06 3.9E+06 2.6E+06 1.3E+06 -0.10 -0.08 -0.06 -0.04 0.0E+00 -0.02 0.00 -1.3E+06 0.02 0.04 0.06 0.08 0.10 Displacem ent, [m ] When friction is present with = 0.1, the relative displacement is reduced to 4.3 cm. When friction is absent, the absolute acceleration is limited to 0.5m/s2, the stiffness of the braces limiting (practically without a shock) the relative displacement. When friction is present with = 0.1, the absolute acceleration is 1 m/s2, a value resulted from the action of the ground on the building via friction. Fig. 10. Stiffness-displacement caracteristics for the limiting and recurrence cross-bracing Fig. 11. Time variation of relative displacements for an oscilant system with telescopic devices = 0, and 0.1 All these analyses conclude that the presence of friction is limiting the relative displacement and the absolute acceleration both in case of resonance and out of it. The seismic isolation solution proposed in the paper, is combining the phenomenon of seismic isolation due to the moving-away of the vibration period (to a ratio of 3 as to the eagen period of the oscillating system - embedded into the ground - and as to the fundamental oscillation period of the ground) with the friction phenomenon for to limit the relative movement. The absolute accelerations are much reduced, under the value of the maximum ground acceleration. The use of the telescopic devices with obvious non-linear characteristic and strengthening, allows both the limitation of the random maximum relative displacements and shocks that may occur during an earthquake, and the system revert (even partially) to the initial condition before the earthquake. The computations were conducted without considering the short moments in which the mass is rigidly (without gliding) engaged by the ground. In case of some friction ratios considered high 9 WEC REGIONAL ENERGY FORUM – FOREN 2008 Neptun, 15-19 June 2008 for the isolation phenomenon, ( > 0.1) such a rigid engagement have a unfavorable effect. Therefore it is desirable that the friction ratio be as small as possible ( ~ 0.03-0.07) so to provide gliding within the longest possible displacement range associated to an oscillation cycle. 9. Conclusions In order to reduce the seismic loads on the Reactor Building-Spent Fuel Bay Building assembly in CANDU PHWR 600 nuclear power plants and ACR type nuclear power plants the proposal consists in the seismic isolation of the assembly by the use of SERB 800 X 800 type devices. The new proposed solution for the seismic qualification shows technical and economic advantages and it also shortens the period of construction. All the systems, equipment and piping systems in the two buildings need not be seismically qualified because the seismic acceleration transferred to the two buildings with SERB –SITON isolation system, is much below 0.1 g (function of the dynamic friction ratio during gliding) on any direction in horizontal plane, irrespective of the seismic acceleration on site. For to substantiate the seismic isolation solution analyses the applied input data were the seismic design data for Cernavoda NPP Site. Since a maximum relative displacement of building180 mm was imposed, sizing of the seismic isolation devices has been done (stiffness and equivalent damping). Following to the theoretical and numerical analyses, also considering the gliding – induced friction, the results showed that the maximum relative displacement between the building, seismically isolated by SERB 800 X 800 devices, and the foundation ground is maximum 100 mm and the maximum seismic acceleration transferred to the buildings is 0.05 g in case that the friction ratio between the PTFE and stainless steel surface is 0.05. REFERENCES 1. Invention patent, No.119845 B1/29.04.2005, Sandwich structure device, including a sandwich structure and a network of devices for to overtake and damp so to control the behavior of buildings, equipment and pipes network under loads conditions; 2. Invention patent, No. Nr.119822 B1/29.04.2005, Sandwisch structure device and copmact device to overtake static and dynamic loads; 3. V. Serban, A. Panait, I. Prisecaru “SITON solutions to increase new or existing NPP’s reliability & safety by controlling, limitting and damping shocks, vibrations & seismic movements”, ENERGIA NUCLEARA Magazine, VOL.18 /Nr. 1-2/2006; 4.OKAWA, Legislative Approval Procedures of the Buildings with Base Isolation System and/or Vibration Control System, Building Research Institute, Tachihara 1, Tsukuba, Ibaraki 305-0802, Japan, Feb. 22, 2005; 5. M. MIDORIKAWA, M. IIBA, N. KOSHIKA, Seismic Performance Evaluation of Seismically Isolated Buildings Introduced to the Building Code of Japan, Feb. 2004; 6. Trevor, E. Kelly, BASE ISOLATION OF STRUCTURES, Holmes Consulting Group Ltd., Rev.0, July 2001; 7. SITON document – Reduction of seismic hazard on Cernavoda NPP Site by the use of some mechanical devices capable to disipate the seismic energy and to control the dynamic behavior of structures, also applicable to classic buildings, Contract 313/2003, MENER 2003; 8. SITON document – Evaluation of the mass asymetry and internal structures stiffness effects on the reactor building and on the seismic input for equipment and piping systems inside the building. Technical solutions to increase the the seismic safety margin of equipment in the CANDU-PHWR 600 – reactor building, contract 285/2007. 10