Download 63-1337-01 - Class 200 Meters Three-Phase Meters

Class 200 Meters
Three-Phase Meters
SPECIFICATION DATA
FEATURES
• 0-2 volt output split-core current sensors allow for
quick and safe installation without power interruption.
• Retain meter reading in the event of power failure.
• Meters can be placed up to 2,000 feet away from an
electric panel.
• Current sensor installation diagnostic indicator.
• UL/CUL Listed with utility-grade accuracy.
• Parallel up to three (3) sets of current sensors for
cumulative reading.
• Meter can be used on the following configurations:
3-Phase, 4-Wire
3-Phase, 3-Wire
2-Phase, 3-Wire
• Optional removable terminal block for pulse output.
• Industrial-grade JIC steel enclosure with padlocking
hasp and mounting flanges for indoor installations
with 1-1/16 in. KO (3/4 in. Cond.) on bottom of
enclosure.
• Non-volatile Memory.
SPECIFICATIONS
OVERVIEW
The Honeywell Class 200 kWh meters are fully electronic,lowcost meters for monitoring electrical usage in multifamily,commercial and industrial applications.
APPLICATIONS
Metering specific tenants, departments, cost centers or pieces
of equipment in your facility allows you to pinpoint when and
where energy is being used—right down to the specific date
and time. Armed with this data, you can take steps to curtail
this usage and thus reduce your overall energy consumption
costs.
• Ideal for indoor and outdoor use.
• Monitors a single electrical circuit, piece of equipment,
department, tenant, or even the entire building.
• Easy and affordable installation virtually anywhere,
including both new and retrofitted facilities.
Dimensions:
7-1/4 in. H x 7 in. W x 3-1/4 in. D
Accuracy:
Certified to ANSI C12.1 & C12.16
Voltage Input Configuration:
4 wire 120/208-240 volt
3 wire 240 volt
4 wire 277/480 volt
3 wire 480 volt
Current Input:
Up to 3200 Amp RMS AC
Power Factor: .5 leading and lagging
Frequency: 50-60 HZ
Temperature Range:
Operating Temp: -20°C to 50°C.
Relative Humidity Range:
0-95% Non-Condensing
Voltage Overload:
+25% Continuously; +100% for 20 cycles
Pulse Output Type:
Optically coupled, normally open electronic switch.
Output:
Solid-state switch, N.O. equivalent.
®
63-1337-01
CLASS 200 METERS THREE-PHASE METERS
Typical ON Resistance:
30 Ohms
Maximum OFF Leakage:
1 uA
Pulse Closure Time Cycle:
50%
External Interface Voltage:
1.5 to 36 volts DC or AC
Maximum Interface Current:
100 ma
Current Sensor Overload:
100% for 1 minute without damaging meter
Approvals:
UL Listed and CSA Approved
3-3/4 (95)
1-19/64 (33)
1-1/2
(38)
1-3/8
(35)
4-1/4
(108)
29/32
(23)
1-3/16
(30)
M29269
Fig. 3. 400 Amp current sensor dimensions in in. (mm).
1-1/4
(32)
6-3/32 (155)
7 (178)
3-1/4 (83)
2-3/8
(60)
4-19/64
(109)
7-1/2
(191)
5-3/4
(146)
M29258
Fig. 1. Class 200 meter enclosure dimensions in in. (mm).
M29270
Fig. 4. 800 and 1600 Amp current sensor dimensions in
in. (mm).
3-3/4 (95)
29/32
(23)
1-19/64 (33)
1-1/4
(32)
7-3/4 (197)
1-3/8
(35) 2-3/4
(70)
M29268
Fig. 2. 100 and 200 Amp current sensor dimensions in in.
(mm).
9-3/32
(231)
5-3/8 (137)
7-7/8
(200)
M29271
Fig. 5. 3200 Amp current sensor dimensions in in. (mm).
63-1337—01
2
CLASS 200 METERS THREE-PHASE METERS
ORDERING INFORMATION
Table 1. Model Numbers.
Model #
Amps
SUB208-100
100
SUB208-200
200
SUB208-400
400
SUB208-800
800
SUB208-1600
1600
SUB208-3200
3200
SUB480-100
100
SUB480-200
200
SUB480-400
400
SUB480-800
800
SUB480-1600
1600
SUB480-3200
3200
Description
120/208-240V, 3-Phase, 4W
240V, 3-Phase, 3W
(Supplied with one set of three (3)
split-core current sensors)
277/480V, 3-Phase, 4W
480V, 3-Phase, 3W
(Supplied with one set of three (3)
split-core current sensors)
3
63-1337—01
CLASS 200 METERS THREE-PHASE METERS
Automation and Control Solutions
Honeywell International Inc.
Honeywell Limited-Honeywell Limitée
1985 Douglas Drive North
35 Dynamic Drive
Golden Valley, MN 55422
Toronto, Ontario M1V 4Z9
customer.honeywell.com
® U.S. Registered Trademark
© 2009 Honeywell International Inc.
63-1337—01 M.S. 04-09