* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Amplifier Circuits Quiz - e-VET
Crystal radio wikipedia , lookup
Phase-locked loop wikipedia , lookup
Flip-flop (electronics) wikipedia , lookup
Power MOSFET wikipedia , lookup
Integrating ADC wikipedia , lookup
Superheterodyne receiver wikipedia , lookup
Loudspeaker wikipedia , lookup
Power electronics wikipedia , lookup
Oscilloscope types wikipedia , lookup
Analog-to-digital converter wikipedia , lookup
Oscilloscope history wikipedia , lookup
Cellular repeater wikipedia , lookup
Instrument amplifier wikipedia , lookup
Audio crossover wikipedia , lookup
Naim Audio amplification wikipedia , lookup
Scattering parameters wikipedia , lookup
Standing wave ratio wikipedia , lookup
Transistor–transistor logic wikipedia , lookup
Dynamic range compression wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Schmitt trigger wikipedia , lookup
Wilson current mirror wikipedia , lookup
Current mirror wikipedia , lookup
Nominal impedance wikipedia , lookup
Audio power wikipedia , lookup
Distortion (music) wikipedia , lookup
Two-port network wikipedia , lookup
Rectiverter wikipedia , lookup
Index of electronics articles wikipedia , lookup
Radio transmitter design wikipedia , lookup
Zobel network wikipedia , lookup
Public address system wikipedia , lookup
Regenerative circuit wikipedia , lookup
Opto-isolator wikipedia , lookup
Negative feedback wikipedia , lookup
Operational amplifier wikipedia , lookup
Amplifier basics QUIZ 1. If a power amplifier produces an output 10 times greater than its input, what will its power gain be, measured in deciBels? a) 3dB b) 6dB c) 10dB d) 20dB 2. If the base current Ib of a common emitter amplifier is 40µA and the hfe of the transistor is 200, what will the collector current? a) 240µA b) 800µA c) 25µA d) 8mA 3. In Fig 1.5.1 what is the purpose of block B? a) A Tuned RF amplifier b) An FM amplifier c) An IF amplifier d) An AF pre-amplifier 4. Which of these formulae gives the voltage gain of an amplifier? a) Vout/ Vin b) Vin/ Vout c) Vout/ Iin d) d) Vin x hfe 5. Complete this sentence: "Class A bias... a) ...gives high gain and low distortion". b) ...gives high gain and low distortion". c) ...gives low distortion and low efficiency". d) ...gives low distortion and low gain". 6. Complete this sentence: "Class A bias sets the quiescent current... a) ...below cut off". b) ...above cut off". c) ...at Ib = 0". d) ...at cut off". 7. What is the voltage gain of an amplifier at the half power points on the amplifier response curve? a) 0.5 b) 0.707 c) 1.414 d) 6.0 8. What is the purpose of C3 in Fig 1.5.2? a) To prevent HF noise. b) To prevent saturation. c) To prevent thermal runaway. d) d)To prevent negative feedback. 9. In Fig 1.5.2 which component will be mainly responsible for limiting high frequency gain? a) Tr1 b) C2 c) C3 d) C4 10. What is the advantage of extending the bandwidth of audio amplifiers to frequencies higher than the audible limit? a) To reduce noise. b) To increase efficiency. c) To preserve wave shape. d) To reduce transients. Amplifier Circuits Quiz Try our quiz, based on the information you can find in Amplifiers Module 4. Submit your answers and see how many you get right. If you get any answers wrong. Just follow the hints to find the right answer and learn about Amplifiers as you go. 1. What would be the function of the control circuit shown in Fig. 4.4.1 in an audio amplifier? a) Volume. b) Balance. c) Treble boost. d) Tone. 2. What is the purpose of RIAA de-emphasis in an audio pre-amplifier? a) To provide correct impedance matching on a MIC input. b) To provide D to A conversion on a CD input. c) To provide frequency correction on a PHONO input. d) To provide level correction on a line level output. 3. When the bass and treble controls in a Baxandall passive tone control circuit are set at their mid point, what will be the approximate voltage gain of the tone control circuit? a) -3dB b) -6dB c) -20dB d) -40dB 4. Complete the following sentence: Compared with a bipolar transistor, using a JFET transistor in the input stage of an audio amplifier instead of a bipolar transistor provides... a) ...higher input impedance and reduced signal to noise ratio. b) ...higher input impedance and increased signal to noise ratio. c) ...higher gain and increased signal to noise ratio. d) ...higher gain and reduced signal to noise ratio. 5. Bootstrapping in an amplifier circuit refers to which of the following techniques? a) Using positive feedback to increase the apparent input impedance of the amplifier. b) Using negative feedback to increase the apparent input impedance of the amplifier. c) Using negative feedback to reduce the apparent output impedance of the amplifier. d) Using positive feedback to increase the stability of the amplifier. 6. Which of the following features does the circuit illustrated in Fig. 4.4.2 posess? a) High voltage gain and very high input impedance. b) Low voltage gain and very high output impedance. c) High current gain and very high input impedance. d) Low current gain and very high output impedance. 7. Which of the following would be a typical value for the input impedance of a common collector amplifier? a) 1KΩ b) 15KΩ c) 150KΩ d) 15MΩ 8. Refer to Fig 4.4.3. If the real value of R3 is 33KΩ and the open loop gain of the emitter follower amplifier (AO) is 0.98, what will be the apparent value R3? a) 1.65MΩ b) 2.35MΩ c) 3.27MΩ d) 230.5KΩ