Download MTP3N60E Designer`s™ Data Sheet TMOS E−FET.™ High Energy

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Stepper motor wikipedia , lookup

Three-phase electric power wikipedia , lookup

Memristor wikipedia , lookup

Islanding wikipedia , lookup

Immunity-aware programming wikipedia , lookup

Electrical ballast wikipedia , lookup

History of electric power transmission wikipedia , lookup

Power inverter wikipedia , lookup

Thermal runaway wikipedia , lookup

Variable-frequency drive wikipedia , lookup

Pulse-width modulation wikipedia , lookup

Electrical substation wikipedia , lookup

Electromagnetic compatibility wikipedia , lookup

Rectifier wikipedia , lookup

Triode wikipedia , lookup

Metadyne wikipedia , lookup

Ohm's law wikipedia , lookup

Voltage regulator wikipedia , lookup

Transistor wikipedia , lookup

Distribution management system wikipedia , lookup

Power electronics wikipedia , lookup

Stray voltage wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Voltage optimisation wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Current source wikipedia , lookup

Alternating current wikipedia , lookup

Surge protector wikipedia , lookup

Mains electricity wikipedia , lookup

Buck converter wikipedia , lookup

Opto-isolator wikipedia , lookup

Transcript
MTP3N60E
Designer’s™ Data Sheet
TMOS E−FET.™
High Energy Power FET
N−Channel Enhancement−Mode Silicon
Gate
This advanced high voltage TMOS E−FET is designed to withstand
high energy in the avalanche mode and switch efficiently. This new
high energy device also offers a drain−to−source diode with fast
recovery time. Designed for high voltage, high speed switching
applications such as power supplies, PWM motor controls and other
inductive loads, the avalanche energy capability is specified to
eliminate the guesswork in designs where inductive loads are switched
and offer additional safety margin against unexpected voltage
transients.
• Avalanche Energy Capability Specified at Elevated
Temperature
• Low Stored Gate Charge for Efficient Switching
• Internal Source−to−Drain Diode Designed to Replace External Zener
Transient Suppressor — Absorbs High Energy in the Avalanche
Mode
• Source−to−Drain Diode Recovery Time Comparable to Discrete
Fast Recovery Diode
http://onsemi.com
TMOS POWER FET
3.0 AMPERES, 600 VOLTS
RDS(on) = 2.2 W
TO-220AB
CASE 221A−09
Style 5
D
®
G
S
Preferred devices are Motorola recommended choices for future use and best overall value.
© Semiconductor Components Industries, LLC, 2006
August, 2006 − Rev. 3
1
Publication Order Number:
MTP3N60E/D
MTP3N60E
MAXIMUM RATINGS (TC = 25°C unless otherwise noted)
Rating
Symbol
Value
Unit
Drain−Source Voltage
VDSS
600
Vdc
Drain−Gate Voltage (RGS = 1.0 MΩ)
VDGR
600
Vdc
Gate−Source Voltage — Continuous
Gate−Source Voltage — Non−repetitive
VGS
VGSM
± 20
± 40
Vdc
Vpk
Drain Current — Continuous
Drain Current — Continuous @ 100°C
Drain Current — Pulsed
ID
ID
3.0
2.4
14
Adc
PD
75
0.6
Watts
W/°C
TJ, Tstg
−55 to 150
°C
WDSR(1)
mJ
WDSR(2)
290
46
7.5
RθJC
RθJA
1.67
62.5
°C/W
TL
260
°C
IDM
Total Power Dissipation @ TC = 25°C
Derate above 25°C
Operating and Storage Temperature Range
UNCLAMPED DRAIN−TO−SOURCE AVALANCHE CHARACTERISTICS (TJ < 150°C)
Single Pulse Drain−to−Source Avalanche Energy — TJ = 25°C
Single Pulse Drain−to−Source Avalanche Energy — TJ = 100°C
Repetitive Pulse Drain−to−Source Avalanche Energy
THERMAL CHARACTERISTICS
Thermal Resistance — Junction to Case°
Thermal Resistance — Junction to Ambient°
Maximum Lead Temperature for Soldering Purposes, 1/8″ from case for 10 seconds
(1) VDD = 50 V, ID = 3.0 A
(2) Pulse Width and frequency is limited by TJ(max) and thermal response
Designer’s Data for “Worst Case” Conditions — The Designer’s Data Sheet permits the design of most circuits entirely from the information presented. SOA Limit
curves — representing boundaries on device characteristics — are given to facilitate “worst case” design.
http://onsemi.com
2
MTP3N60E
ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise noted)
Characteristic
Symbol
Min
Typ
Max
Unit
Drain−to−Source Breakdown Voltage
(VGS = 0, ID = 250 μAdc)
V(BR)DSS
600
—
—
Vdc
Zero Gate Voltage Drain Current
(VDS = 600 V, VGS = 0)
(VDS = 480 V, VGS = 0, TJ = 125°C)
IDSS
—
—
—
—
10
100
OFF CHARACTERISTICS
μAdc
Gate−Body Leakage Current — Forward (VGSF = 20 Vdc, VDS = 0)
IGSSF
—
—
100
nAdc
Gate−Body Leakage Current — Reverse (VGSR = 20 Vdc, VDS = 0)
IGSSR
—
—
100
nAdc
2.0
1.5
—
—
4.0
3.5
—
2.1
2.2
—
—
—
—
9.0
7.5
gFS
1.5
—
—
mhos
Ciss
—
770
—
pF
Coss
—
105
—
Crss
—
19
—
td(on)
—
23
—
tr
—
34
—
td(off)
—
58
—
tf
—
35
—
Qg
—
28
31
Qgs
—
5.0
—
Qgd
—
17
—
VSD
—
—
1.4
Vdc
ton
—
**
—
ns
trr
—
400
—
—
—
3.5
4.5
—
—
—
7.5
—
ON CHARACTERISTICS*
Gate Threshold Voltage
(VDS = VGS, ID = 250 μAdc)
(TJ = 125°C)
VGS(th)
Static Drain−to−Source On−Resistance (VGS = 10 Vdc, ID = 1.5 A)
RDS(on)
Drain−to−Source On−Voltage (VGS = 10 Vdc)
(ID = 3.0 A)
(ID = 1.5 A, TJ = 100°C)
VDS(on)
Forward Transconductance (VDS = 15 Vdc, ID = 1.5 A)
Vdc
Ohms
Vdc
DYNAMIC CHARACTERISTICS
Input Capacitance
Output Capacitance
(VDS = 25 V, VGS = 0,
f = 1.0 MHz)
Transfer Capacitance
SWITCHING CHARACTERISTICS*
Turn−On Delay Time
Rise Time
Turn−Off Delay Time
(VDD = 300 V, ID ≈ 3.0 A,
RL = 100 Ω, RG = 12 Ω,
VGS(on) = 10 V)
Fall Time
Total Gate Charge
Gate−Source Charge
Gate−Drain Charge
(VDS = 420 V, ID = 3.0 A,
VGS = 10 V)
ns
nC
SOURCE−DRAIN DIODE CHARACTERISTICS
Forward On−Voltage
Forward Turn−On Time
(IS = 3.0 A, di/dt = 100 A/μs)
Reverse Recovery Time
INTERNAL PACKAGE INDUCTANCE
Internal Drain Inductance
(Measured from the contact screw on tab to center of die)
(Measured from the drain lead 0.25″ from package to center of die)
Ld
Internal Source Inductance
(Measured from the source lead 0.25″ from package to source bond pad)
Ls
* Pulse Test: Pulse Width = 300 μs, Duty Cycle ≤ 2.0%.
** Limited by circuit inductance.
http://onsemi.com
3
nH
MTP3N60E
I D, DRAIN CURRENT (AMPS)
8
VGS = 10 V
VGS(th), GATE THRESHOLD VOLTAGE (NORMALIZED
TYPICAL ELECTRICAL CHARACTERISTICS
7V
6
4
6V
2
5V
0
0
4
8
12
16
6
10
14
VDS, DRAIN−TO−SOURCE VOLTAGE (VOLTS)
2
18
20
1.2
1
0.9
0.8
0.7
−50
I D, DRAIN CURRENT (AMPS)
10
VDS ≥ 10 V
6
4
100°C
2
0
TJ = 25°C
0
1
−55°C
2
4
6
3
5
7
VGS, GATE−TO−SOURCE VOLTAGE (VOLTS)
8
9
RDS(on) , DRAIN−TO−SOURCE ON−RESISTANCE
(NORMALIZED)
RDS(on) , DRAIN−TO−SOURCE RESISTANCE (OHMS)
100°C
TJ = 25°C
2
−55°C
0
4
6
1
1.1
VGS = 0
ID = 250 μA
1
0.9
0.8
−50
−25
0
25
50
75
100
125
1
Figure 4. Breakdown Voltage Variation
With Temperature
4
2
125
TJ, JUNCTION TEMPERATURE (°C)
6
0
0
25
50
75
100
TJ, JUNCTION TEMPERATURE (°C)
1.2
Figure 3. Transfer Characteristics
VGS = 10 V
−25
Figure 2. Gate−Threshold Voltage Variation
With Temperature
VBR(DSS), DRAIN−TO−SOURCE BREAKDOWN VOLTAGE
(NORMALIZED)
Figure 1. On−Region Characteristics
8
VDS = VGS
ID = 0.25 mA
1.1
8
10
3
VGS = 10 V
ID = 2 A
2
1
0
−50
−25
0
25
50
75
100
125
ID, DRAIN CURRENT (AMPS)
TJ, JUNCTION TEMPERATURE (°C)
Figure 5. On−Resistance versus Drain Current
Figure 6. On−Resistance Variation
With Temperature
http://onsemi.com
4
1
MTP3N60E
SAFE OPERATING AREA INFORMATION
16
VGS = 20 V
SINGLE PULSE
TC = 25°C
I D, DRAIN CURRENT (AMPS)
I D, DRAIN CURRENT (AMPS)
100
10 μs
10
100 μs
10 ms
1 ms
dc
1
RDS(on) LIMIT
THERMAL LIMIT
PACKAGE LIMIT
0.1
1
12
8
TJ ≤ 150°C
4
0
100
10
VDS, DRAIN−TO−SOURCE VOLTAGE (VOLTS)
1000
0
Figure 7. Maximum Rated Forward Biased
Safe Operating Area
600
200
400
VDS, DRAIN−TO−SOURCE VOLTAGE (VOLTS)
80
Figure 8. Maximum Rated Switching
Safe Operating Area
The power averaged over a complete switching cycle
must be less than:
FORWARD BIASED SAFE OPERATING AREA
TJ(max) − TC
RθJC
The FBSOA curves define the maximum drain−to−source
voltage and drain current that a device can safely handle
when it is forward biased, or when it is on, or being turned
on. Because these curves include the limitations of
simultaneous high voltage and high current, up to the rating
of the device, they are especially useful to designers of
linear systems. The curves are based on a case
temperature of 25°C and a maximum junction temperature
of 150°C. Limitations for repetitive pulses at various case
temperatures can be determined by using the thermal
response curves. Motorola Application Note, AN569,
“Transient Thermal Resistance−General Data and Its Use”
provides detailed instructions.
10000
VDD = 300 V
ID = 3 A
VGS(on) = 10 V
TJ = 25°C
t, TIME (ns)
1000
td(off)
tf
td(on)
100
tr
SWITCHING SAFE OPERATING AREA
The switching safe operating area (SOA) of Figure 8 is
the boundary that the load line may traverse without
incurring damage to the MOSFET. The fundamental limits
are the peak current, IDM and the breakdown voltage,
V (BR)DSS . The switching SOA shown in Figure 8 is
applicable for both turn−on and turn−off of the devices for
switching times less than one microsecond.
10
1
10
100
RG, GATE RESISTANCE (OHMS)
Figure 9. Resistive Switching Time
Variation versus Gate Resistance
http://onsemi.com
5
100
RGS
DUT
MTP3N60E
−
1
I D, DRAIN CURRENT (AMPS)
r(t), NORMALIZED EFFECTIVE
TRANSIENT THERMAL RESISTANCE
4
3
0.5
0.3
0.05
0.03
VGSP(pk)
0.05
0.02
di/dt ≤ 60 A/μs
0
0.02
0.05
RθJC(t) = r(t) RθJC
RθJC = 1.67°C/W MAX
VR = 80%
OF RATED
VDS
D CURVES
APPLY
FOR POWER
VdsL
= Vf +SHOWN
Li ⋅ dls/dt
PULSE
TRAIN
READ TIME AT t1
TJ(pk) − TC = P(pk) RθJC(t)
t1
t2
0.01
0.02
0.01
0.01
VDS
20 V
−
0.1
0.1
Li
IS
+
0.2
DUTY CYCLE,
D = t1/t2
Figure
13. Commutating
Safe Operating Area
Test Circuit
SINGLE PULSE
0
IFM
+
0.2
2
1
VR
D = 0.5
0.1
0.2
200
400
600
VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS)
0.5
1
2
5
10
20
50
100
200
500
1
t, TIME (ms)
800
V(BR)DSSResponse
Figure 10. Thermal
Figure 12. Commutating Safe Operating Area (CSOA)
Vds(t)
COMMUTATING SAFE OPERATING AREA (CSOA)
IO
15 V
The Commutating Safe Operating Area (CSOA) of Figure
L
12 defines the limits of safe operation
for commutated
source-drain current Vversus re-applied drain voltage
when
C
DS
the source-drain diode has undergone forward
4700bias.
μF The
ID
VR250
forV a given
curve shows the limitations of IFM and peak
commutation speed. It is applicable when waveforms
VDD
similar to those of Figure 11 are present. Full or half-bridge
PWM DC motor controllers are common applications
t
requiring CSOA
data.
The time interval tfrr is Rthe
GS speed of the commutation
50 Ω
cycle. Device stresses increase
with commutation speed,
so t frr is specified with a minimum value. Faster
commutation
speeds
require an appropriate
of IFM,
Figure
14. Unclamped
Inductive derating
Switching
peak VR or both. Ultimately,
tfrr is
limited primarily by device,
Test
Circuit
package, and circuit impedances. Maximum device stress
occurs during trr as the diode goes from conduction to
reverse blocking.
VDS(pk) is the peak drain−to−source voltage that the
device must sustain during commutation; I FM is the
maximum forward source-drain diode current just prior to
the onset of commutation.
VR is specified at 80% of V(BR)DSS to ensure that the
CSOA stress is maximized as IS decays from IRM to zero.
RGS should be minimized during commutation. TJ has
only a second order effect on CSOA.
Stray inductances, L i in Motorola’s test circuit are
assumed to be practical minimums.
VGS
0
IFM
90%
ID(t)
dlS/dt
IS
trr
10%
VDD
ton
IRM
tP
0.25 It,RM(TIME)
V(BR)DSS
WDSR + 1 LIO2 2
V(BR)DSS–VDD
VDS(pk)
tfrr
ǒ
Ǔǒ
Ǔ
VR Inductive Switching
Figure 15. Unclamped
Waveforms
VDS
Vf
VdsL
MAX. CSOA
STRESS AREA
Figure 11. Commutating Waveforms
http://onsemi.com
6
MTP3N60E
TJ = 25°C
1400
VGS = 0 V
1200
C, CAPACITANCE (pF)
VGS, GATE−TO−SOURCE VOLTAGE (VOLTS)
1600
1000
Ciss
Crss
800
600
400
200
0
10
VDS = 0 V
5
Coss
0
VGS
10
5
20
15
16
12
250 V
420 V
8
4
0
25
VDS = 100 V
TJ = 25°C
ID = 3 A
0
10
20
30
15
25
Qg, TOTAL GATE CHARGE (nC)
5
VDS
GATE−TO−SOURCE OR DRAIN−TO−SOURCE VOLTAGE (VOLTS)
Figure 16. Capacitance Variation
Figure 17. Gate Charge versus
Gate−To−Source Voltage
+18 V
VDD
1 mA
Vin
10 V
15 V
SAME
DEVICE TYPE
AS DUT
100 k
2N3904
0.1 μF
2N3904
100 k
47 k
100
FERRITE
BEAD
Vin = 15 Vpk; PULSE WIDTH ≤ 100 μs, DUTY CYCLE ≤ 10%
Figure 18. Gate Charge Test Circuit
http://onsemi.com
7
DUT
35
4
MTP3N60E
PACKAGE DIMENSIONS
CASE 221A−09
ISSUE Z
−T−
T
SEATING
PLANE
C
S
4
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION Z DEFINES A ZONE WHERE ALL
BODY AND LEAD IRREGULARITIES ARE
ALLOWED.
DIM
A
B
C
D
F
G
H
J
K
L
N
Q
R
S
T
U
V
Z
A
Q
1 2 3
U
H
K
Z
L
R
V
J
G
D
N
INCHES
MIN
MAX
0.570
0.620
0.380
0.405
0.160
0.190
0.025
0.035
0.142
0.147
0.095
0.105
0.110
0.155
0.018
0.025
0.500
0.562
0.045
0.060
0.190
0.210
0.100
0.120
0.080
0.110
0.045
0.055
0.235
0.255
0.000
0.050
0.045
−−−
−−−
0.080
STYLE 5:
PIN 1.
2.
3.
4.
MILLIMETERS
MIN
MAX
14.48
15.75
9.66
10.28
4.07
4.82
0.64
0.88
3.61
3.73
2.42
2.66
2.80
3.93
0.46
0.64
12.70
14.27
1.15
1.52
4.83
5.33
2.54
3.04
2.04
2.79
1.15
1.39
5.97
6.47
0.00
1.27
1.15
−−−
−−−
2.04
GATE
DRAIN
SOURCE
DRAIN
E−FET and Designer’s are trademarks of Motorola, Inc. TMOS is a registered trademark of Motorola, Inc.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
8
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MTP3N60E/D