* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download LED Bulkhead 20cm Installation and Operating Instructions
Survey
Document related concepts
Stray voltage wikipedia , lookup
Mains electricity wikipedia , lookup
Electrical engineering wikipedia , lookup
Power over Ethernet wikipedia , lookup
Portable appliance testing wikipedia , lookup
Anastasios Venetsanopoulos wikipedia , lookup
Telecommunications engineering wikipedia , lookup
Electrical connector wikipedia , lookup
Loading coil wikipedia , lookup
Electrician wikipedia , lookup
Home wiring wikipedia , lookup
National Electrical Code wikipedia , lookup
Transcript
Installation & Operating Instructions 20cm LED BULKHEAD NOTE – To comply with regulations, installation must be carried out by qualified electrician and in accordance with the current IEE Wiring Regulations (BS7671) and Building Regulations. LBM200W6S40 (7625H) ENSURE ELECTRICAL SUPPLY IS DISCONNECTED/ISOLATED BEFORE COMMENCING INSTALLATION SPECIFICATIONS • Suitable for use with Mains voltage of 220-240V AC • This product must be disconnected before insulation resistance testing of the lighting circuit • Check for electrical cables and pipes before installation IP65 650 9W LED LUMINAIRE RATED LUMENS CRI >80 1 Note: This Luminaire is rated to IP65, only when fitted with suitable Gland and Rubber cable. IP65 is rated for use against dust and low pressure water. cable entry points cable entry points SUGGESTED METHOD OF INSTALLATION 3 2 The bulkhead is designed for mounting in any of the following options: – • Surface Wall Mounting loosen screws here • Surface Ceiling Mounting 1. Surface mounted options may use rear cable entry for flush mounting or there is facility for surface Conduit ‘besa’ box mounting or side conduit entry. (Image 1) 2. With the method of mounting chosen, remove the front Diffuser, by undoing the three front Screws. (Image 2) loosen screws here 4 3. To remove LED tray, loosen two retaining screws, and twist tray clockwise and remove. (Image 3) 4. This Bulkhead can be mounted on ceilings and vertical walls. Ensure the mounting surface is suitable for installation. Once mounting points are decided, drill out mounting holes and any cable entry points needed. Page 1 Tech Help Line 0845 194 7584 Non UK - +44 (0)1952 238 100 UK - Supplied by BG Electrical Ltd Stafford Park 1 TF3 3BD ENGLAND Luceco is a registered trade mark of Nexus Industries Ltd. Visit our website at www.luceco.uk Installation & Operating Instructions 5. Cable Entry Points must be drilled out with a 20mm bit, cleaned of any loose burrs and fitted with a suitable IP65 gland, if the IP65 rating is to be maintained. Otherwise the IP rating would be reduced. 5 6. To maintain the IP65 rating of the bulkhead, a suitable 20mm cable gland should be used in conjunction with rubber insulated cable to ensure the supply cable is sealed in the gland. Failure to use a gland and/or rubber insulated cable may result in water ingress WIRE UP 6 5 With the bulkhead securely fixed in the desired position, make the electrical connection to the terminal block, observing the correct polarity. (Image 5) Earth = Green/yellow Sleeving Neutral = Black (pre April 04)/ Blue (post April 04) Live = Red (pre April 04)/ Brown (post April 04) Once the electrical connections have been made, the gear tray can be fitted back into position and secured by twisting Anti-clockwise and tightening the 2no. Fixing screws. tighten screws here Re-fit the front diffuser and tighten 3 securing screws. Turn on power and operate. (Image 7) Environmental Protection W.E.E.E Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice. Page 2 Tech Help Line 0845 194 7584 Non UK - +44 (0)1952 238 100 UK - Supplied by BG Electrical Ltd Stafford Park 1 TF3 3BD ENGLAND Luceco is a registered trade mark of Nexus Industries Ltd. Visit our website at www.luceco.uk