* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Auto Transformer Current Flow
Spark-gap transmitter wikipedia , lookup
Ground loop (electricity) wikipedia , lookup
Mercury-arc valve wikipedia , lookup
Induction motor wikipedia , lookup
Pulse-width modulation wikipedia , lookup
Ground (electricity) wikipedia , lookup
Power engineering wikipedia , lookup
Power inverter wikipedia , lookup
Electrical ballast wikipedia , lookup
Variable-frequency drive wikipedia , lookup
Resonant inductive coupling wikipedia , lookup
Current source wikipedia , lookup
Schmitt trigger wikipedia , lookup
Power MOSFET wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Single-wire earth return wikipedia , lookup
Power electronics wikipedia , lookup
Distribution management system wikipedia , lookup
Electrical substation wikipedia , lookup
Buck converter wikipedia , lookup
Stepper motor wikipedia , lookup
History of electric power transmission wikipedia , lookup
Rectiverter wikipedia , lookup
Voltage regulator wikipedia , lookup
Surge protector wikipedia , lookup
Opto-isolator wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Stray voltage wikipedia , lookup
Three-phase electric power wikipedia , lookup
Transformer wikipedia , lookup
Voltage optimisation wikipedia , lookup
Auto Transformer Current Flow Principles of Auto Transformers H X H0/X0 Principles of Auto Transformers Principles of Auto Transformers High Voltage Winding Low Voltage Winding Common Winding Section H H I-1 H X X X I-2 I1-I2 H0/X0 H0/X0 H0/X0 I-1 High Voltage Winding 1Ø 500/230 kV 250 MVA Auto Transformer Low Voltage Winding Common Winding Section H 865 X 1029 1,894 865 H0/X0 This is a single phase transformer out of a 500/230 kV bank. This transformer MVA is 300 Fill in the boxes for full load current H 1038 1038 X 2256 1218 H0/X0 1038 Principles of Auto Transformers Advantages of the autotransformer • There are considerable savings in size and weight. • There are decreased losses for a given KVA capacity. • Using an autotransformer connection provides an opportunity for achieving lower series impedances and better regulation. Its efficiency is more when compared with the conventional one. • Its size is relatively very smaller. • Voltage regulation of autotransformer is much better. • Lower cost • Low requirements of excitation current. • Less copper is used in its design and construction. • In conventional transformer the voltage step up or step down value is fixed while in autotransformer, we can vary the output voltage as per out requirements and can smoothly increase or decrease its value as per our requirement. Used in HV Substation due to following reasons: • If we use normal transformer the size of transformer will be very high which leads to heavy weight, more copper and high cost. • The tertiary winding used in Autotransformer balances single phase unbalanced loads connected to secondary and it does not pass on these unbalanced currents to Primary side. Hence Harmonics and voltage unbalance are eliminated. • Tertiary winding in the Autotransformer balances amp turns so that Autotransformer achieves magnetic separation like two winding transformers. Application • Used in both Synchronous motors and induction motors. • Used in electrical apparatus testing labs since the voltage can be smoothly and continuously varied. • They find application as boosters in AC feeders to increase the voltage levels. Disadvantages of the autotransformer • • • • • The autotransformer connection is not available with certain three-phase connections. Higher (and possibly more damaging) short-circuit currents can result from a lower series impedance. Short circuits can impress voltages significantly higher than operating voltages across the windings of an autotransformer. For the same voltage surge at the line terminals, the impressed and induced voltages are greater for an autotransformer than for a two-winding transformer. Autotransformer consists of a single winding around an iron core, which creates a change in voltage from one end to the other. In other words, the self-inductance of the winding around the core changes the voltage potential, but there is no isolation of the high and low voltage ends of the winding. So any noise or other voltage anomaly coming in on one side is passed through to the other. For that reason, Autotransformers are typically only used where there is already some sort of filtering or conditioning ahead of it, as in electronic applications, or the downstream device is unaffected by those anomalies, such as an AC motor during starting.