Installation Instructions
... • Check the ambient temperature rating. The permanet split capacitor units are equipped with thermal cut-outs. Excessive temperatures and cycle frequencies may heat the motor up and the thermal cut-out turns off the motor. Wiring Diagrams ...
... • Check the ambient temperature rating. The permanet split capacitor units are equipped with thermal cut-outs. Excessive temperatures and cycle frequencies may heat the motor up and the thermal cut-out turns off the motor. Wiring Diagrams ...
Heto CB8-30 Service Manual
... Check the line voltage at the compressors and check low line voltage is a frequent problem in many areas. Clean the air cooled condenser. Be sure that the cabinet is located so that the free flow of air through the condenser is not obstructed. Fans should turn freely and run at full speed when energ ...
... Check the line voltage at the compressors and check low line voltage is a frequent problem in many areas. Clean the air cooled condenser. Be sure that the cabinet is located so that the free flow of air through the condenser is not obstructed. Fans should turn freely and run at full speed when energ ...
Evaluates: MAX8739 MAX8739 Evaluation Kit General Description Features
... The MAX8739 EV kit contains a step-up switching regulator, a positive two-stage charge pump, a negative single-stage charge pump, two operational amplifiers, and a high-voltage switch matrix. The EV kit operates from a DC power supply between +1.8V and +5.5V. As configured, the step-up switching reg ...
... The MAX8739 EV kit contains a step-up switching regulator, a positive two-stage charge pump, a negative single-stage charge pump, two operational amplifiers, and a high-voltage switch matrix. The EV kit operates from a DC power supply between +1.8V and +5.5V. As configured, the step-up switching reg ...
FSUSB20 — Low-Power, 1-Port, High-Speed USB (480Mbps) Switch FSUSB20
... -30dB Non-adjacent Channel Crosstalk: 250MHz On Resistance: 4.5Ω Typical (RON) -3dB Bandwidth: >720MHz Low-Power Consumption: 1µA Maximum Control Input: LVTTL Compatible Bi-Directional Operation USB High-Speed and Full-Speed Signaling ...
... -30dB Non-adjacent Channel Crosstalk: 250MHz On Resistance: 4.5Ω Typical (RON) -3dB Bandwidth: >720MHz Low-Power Consumption: 1µA Maximum Control Input: LVTTL Compatible Bi-Directional Operation USB High-Speed and Full-Speed Signaling ...
EVC4000 Instruction Manual - World Precision Instruments
... Connect the preamplifier cable to the receptacle of any available module on the front panel of the instrument. Place the Operate/Stand By switch in Stand By position and the Dummy In/Out toggle switch In. This causes dummy electrodes composed of resistors, as shown in Fig. 3 to be inserted across th ...
... Connect the preamplifier cable to the receptacle of any available module on the front panel of the instrument. Place the Operate/Stand By switch in Stand By position and the Dummy In/Out toggle switch In. This causes dummy electrodes composed of resistors, as shown in Fig. 3 to be inserted across th ...
High-Bandwidth, VGA 2:1 Switch with ±15kV ESD Protection MAX4885AE General Description
... switches to route DDC signals (see Table 2). VL is normally set to +3.3V to provide logic-shifting for VESA I2C-compatible signals. The MAX4885AE protects the low-voltage graphics controller from +5V that could be present in VESA-compatible monitors. In some applications, such as KVM, where logic-le ...
... switches to route DDC signals (see Table 2). VL is normally set to +3.3V to provide logic-shifting for VESA I2C-compatible signals. The MAX4885AE protects the low-voltage graphics controller from +5V that could be present in VESA-compatible monitors. In some applications, such as KVM, where logic-le ...
Switch
In electrical engineering, a switch is an electrical component that can break an electrical circuit, interrupting the current or diverting it from one conductor to another.The mechanism of a switch may be operated directly by a human operator to control a circuit (for example, a light switch or a keyboard button), may be operated by a moving object such as a door-operated switch, or may be operated by some sensing element for pressure, temperature or flow. A relay is a switch that is operated by electricity. Switches are made to handle a wide range of voltages and currents; very large switches may be used to isolate high-voltage circuits in electrical substations.