NLAS54404
... must be implemented to prohibit the current and voltage at the logic pin and signal pins from exceeding the maximum ratings of the switch. The following two methods can be used to provide additional protection to limit the current in the event that the voltage at a signal pin goes below ground by mo ...
... must be implemented to prohibit the current and voltage at the logic pin and signal pins from exceeding the maximum ratings of the switch. The following two methods can be used to provide additional protection to limit the current in the event that the voltage at a signal pin goes below ground by mo ...
MAX4780/MAX4784 0.7 Multiplexers Ω
... Detailed Description The MAX4780/MAX4784 are low 0.7Ω (at V+ = +2.7V) on-resistance, low-voltage, quad 2:1 analog multiplexers/ demultiplexers that operate from a +1.6V to +4.2V single supply. CMOS switch construction allows switching analog signals that are within the supply voltage range (GND to V ...
... Detailed Description The MAX4780/MAX4784 are low 0.7Ω (at V+ = +2.7V) on-resistance, low-voltage, quad 2:1 analog multiplexers/ demultiplexers that operate from a +1.6V to +4.2V single supply. CMOS switch construction allows switching analog signals that are within the supply voltage range (GND to V ...
Muon Pretrigger Electronics - Institut für Experimentalphysik
... has been implemented, which provides the read-out of temperature values and status informations. As shown in Fig.1 there are two systems, one for the FPS detectors and one for the VFPS detectors. Each system consists of a Sensor Module, a Switch Module and a Relay Box. The heart of the system is th ...
... has been implemented, which provides the read-out of temperature values and status informations. As shown in Fig.1 there are two systems, one for the FPS detectors and one for the VFPS detectors. Each system consists of a Sensor Module, a Switch Module and a Relay Box. The heart of the system is th ...
Valve Troubleshooting Guide Product Description
... failure. If motor power does not cut off in both directions within 10 to 14 seconds replace the valve control module.) Passed; If testing detects power in both directions repair or replace motor assembly and move on to step 8. The 12v & 24v systems both use the same 12v valve motor. The valve moto ...
... failure. If motor power does not cut off in both directions within 10 to 14 seconds replace the valve control module.) Passed; If testing detects power in both directions repair or replace motor assembly and move on to step 8. The 12v & 24v systems both use the same 12v valve motor. The valve moto ...
ELECTRICAL EQUIPMENT
... effective in obtaining an immediate start under these conditions. The maximum charging current in the emergency position is very high as there is no drain against it by the lighting system. Therefore, the engine should not be run with the ignition switch in this position for more than 10—15 minutes. ...
... effective in obtaining an immediate start under these conditions. The maximum charging current in the emergency position is very high as there is no drain against it by the lighting system. Therefore, the engine should not be run with the ignition switch in this position for more than 10—15 minutes. ...
250-0003 - Minarik Drives
... mounted optical encoder and exhibiting the results on an illuminated numeric display. Digital indication eliminates the need for “reading between the lines” necessary with analog systems. The VT-3 Series is normally used to display RPM (revolutions per minute) although they can be calibrated to disp ...
... mounted optical encoder and exhibiting the results on an illuminated numeric display. Digital indication eliminates the need for “reading between the lines” necessary with analog systems. The VT-3 Series is normally used to display RPM (revolutions per minute) although they can be calibrated to disp ...
EXTRACT FANS IN DWELLINGS
... isolation is that it is often remote from the extract fan and there is a very real risk of someone inadvertently switching the supply back on. The electrician is therefore required to take adequate precautions against this happening by means such as securing the main switch with a padlock or locking ...
... isolation is that it is often remote from the extract fan and there is a very real risk of someone inadvertently switching the supply back on. The electrician is therefore required to take adequate precautions against this happening by means such as securing the main switch with a padlock or locking ...
Switch
In electrical engineering, a switch is an electrical component that can break an electrical circuit, interrupting the current or diverting it from one conductor to another.The mechanism of a switch may be operated directly by a human operator to control a circuit (for example, a light switch or a keyboard button), may be operated by a moving object such as a door-operated switch, or may be operated by some sensing element for pressure, temperature or flow. A relay is a switch that is operated by electricity. Switches are made to handle a wide range of voltages and currents; very large switches may be used to isolate high-voltage circuits in electrical substations.