Episode Evolution Series Powered Subwoofer Product
... • Ensure that any connected A/V equipment is turned on and connected properly. • Check cable connections for damage, poor contact, or short circuits. • Ensure the subwoofer volume is turned up to a reasonable level. The control is located on the back of the unit. Interference If undesired noise i ...
... • Ensure that any connected A/V equipment is turned on and connected properly. • Check cable connections for damage, poor contact, or short circuits. • Ensure the subwoofer volume is turned up to a reasonable level. The control is located on the back of the unit. Interference If undesired noise i ...
11111-HWS516 Data Sheet產品規格-E1
... The HWS516 is a GaAs PHEMT MMIC SPDT switch with 50 Ω termination operating at 0.5 -3.0 GHz in a low cost miniature USON6L (1.5x1.5x0.4 mm) plastic lead (Pb) free package. The HWS516 features low insertion loss and high isolation with very low DC power consumption. This switch can be used in Bluetoo ...
... The HWS516 is a GaAs PHEMT MMIC SPDT switch with 50 Ω termination operating at 0.5 -3.0 GHz in a low cost miniature USON6L (1.5x1.5x0.4 mm) plastic lead (Pb) free package. The HWS516 features low insertion loss and high isolation with very low DC power consumption. This switch can be used in Bluetoo ...
MAX4645/MAX4646 Fast, Low-Voltage, 2.5 CMOS Analog Switches General Description
... all CMOS devices. Do not exceed the absolute maximum ratings because stresses beyond the listed ratings can cause permanent damage to the devices. Always sequence V+ on first, followed by the logic inputs, NO, or COM. If power-supply sequencing is not possible, add two small signal diodes (D1, D2) i ...
... all CMOS devices. Do not exceed the absolute maximum ratings because stresses beyond the listed ratings can cause permanent damage to the devices. Always sequence V+ on first, followed by the logic inputs, NO, or COM. If power-supply sequencing is not possible, add two small signal diodes (D1, D2) i ...
Cyclone Inline Fans
... 3 Watt LED lamp. This is the only lamp suitable for use with this fan. Do not replace with any other lamp as this will invalidate any warranty. Do not exceed the stated wattage. The fan must be connected to power mains through an automatic circuit breaker integrated into the fixed wiring system with ...
... 3 Watt LED lamp. This is the only lamp suitable for use with this fan. Do not replace with any other lamp as this will invalidate any warranty. Do not exceed the stated wattage. The fan must be connected to power mains through an automatic circuit breaker integrated into the fixed wiring system with ...
... past two years on the determination of soil density and moisture content by nuclear methods. This report consists primarily of an operating manual for the nuclear density-moisture gage involved and its accessory apparatus. It is intended as a practical field guide and includes step-by-step procedure ...
Power Requirements - Rockwell Automation Knowledgebase
... CUTLER HAMMER I/Q 4130 Updated 1/25/2000 ...
... CUTLER HAMMER I/Q 4130 Updated 1/25/2000 ...
MAX4526/MAX4527 Phase-Reversal Analog Switches
... switches, consisting of two normally open and two normally closed CMOS analog switches arranged in a bridge configuration. Analog signals are put into two input pins and taken out of two output pins. A logiclevel signal controls whether the input signal is routed through normally or inverted. A low- ...
... switches, consisting of two normally open and two normally closed CMOS analog switches arranged in a bridge configuration. Analog signals are put into two input pins and taken out of two output pins. A logiclevel signal controls whether the input signal is routed through normally or inverted. A low- ...
Application Notes for LCD 36x24 SmartSwitch/Display
... Shifting the data with Micro-controller pins for many Modules is very time consuming. In this example we assume the data is written via the micro-controller parallel bus to a device such as the 3shift register method described above or via serial port (8-bit mode). The shift speed of data must be su ...
... Shifting the data with Micro-controller pins for many Modules is very time consuming. In this example we assume the data is written via the micro-controller parallel bus to a device such as the 3shift register method described above or via serial port (8-bit mode). The shift speed of data must be su ...
MAX14525 Battery Switch with Four Enable Inputs General Description Features
... The MAX14525 features a low RON 35mΩ (typ) load switch with four unique enable inputs. The MAX14525 is ideal for disconnecting the lithium-ion (Li+) battery from the loads in portable devices such as cell phones. The MAX14525 operates from a +2.2V to +5.5V supply voltage. The MAX14525 features an ex ...
... The MAX14525 features a low RON 35mΩ (typ) load switch with four unique enable inputs. The MAX14525 is ideal for disconnecting the lithium-ion (Li+) battery from the loads in portable devices such as cell phones. The MAX14525 operates from a +2.2V to +5.5V supply voltage. The MAX14525 features an ex ...
Switch
In electrical engineering, a switch is an electrical component that can break an electrical circuit, interrupting the current or diverting it from one conductor to another.The mechanism of a switch may be operated directly by a human operator to control a circuit (for example, a light switch or a keyboard button), may be operated by a moving object such as a door-operated switch, or may be operated by some sensing element for pressure, temperature or flow. A relay is a switch that is operated by electricity. Switches are made to handle a wide range of voltages and currents; very large switches may be used to isolate high-voltage circuits in electrical substations.