Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Infrared Spectroscopy Chapter 16 Dr. Nizam M. El-Ashgar Chemistry Department Islamic University of Gaza 1 IR Spectroscopy I. Introduction A. Spectroscopy is the study of the interaction of matter with the electromagnetic spectrum 1. Electromagnetic radiation displays the properties of both particles and waves 2. The particle component is called a photon 3. The energy (E) component of a photon is proportional to the frequency . Where h is Planck’s constant and n is the frequency in Hertz (cycles per second) E = hn 4. The term “photon” is implied to mean a small, massless particle that contains a small wave-packet of EM radiation/light – we will use this terminology in the course 2 Electromagnetic Radiation • Electromagnetic radiation: light and other forms of radiant energy • Wavelength (): the distance between consecutive identical points on a wave • Frequency (n): the number of full cycles of a wave that pass a point in a second • Hertz (Hz): the unit in which radiation frequency is reported; s-1 (read “per second”). • Molecular spectroscopy: the study of which frequencies of electromagnetic radiation are absorbed or emitted by substances and the correlation between these frequencies and specific types of molecular structure 3 • Wavelength (wavelength) Unit meter (m) millimeter (mm) micrometer (m) nanometer (n m) Angstrom (Å ) Relation to Meter ---1 mm = 10-3 m 1 m = 10-6 m 1 nm = 10-9 m 1 Å = 10-10 m 4 IR radiation does not have enough energy to induce electronic transitions as seen with UV. Absorption of IR is restricted to compounds with small energy differences in the possible vibrational and rotational states. For a molecule to absorb IR, the radiation must interact with the electric field caused by changing dipole moment 5 What is Infrared? Humans, at normal body temperature, radiate most strongly in the infrared, at a wavelength of about 10 microns (A micron is the term commonly used in astronomy for a micrometer or one millionth of a meter). In the image to the left, the red areas are the warmest, followed by yellow, green and blue (coolest). The image to the right shows a cat in the infrared. The yellow-white areas are the warmest and the purple areas are the coldest. This image gives us a different view of a familiar animal as well as information that we could not get from a visible light picture. Notice the cold nose and the heat from the cat's eyes, mouth and ears. 6 IR in Everyday Life Night Vision Goggles 7 • Infrared radiation lies between the visible and microwave portions of the electromagnetic spectrum. • Infrared waves have wavelengths longer than visible and shorter than microwaves, and have frequencies which are lower than visible and higher than microwaves. • The Infrared region is divided into: near, mid and farinfrared. – Near-infrared refers to the part of the infrared spectrum that is closest to visible light. – Far-infrared refers to the part that is closer to the microwave region. – Mid-infrared is the region between these two. 8 • The primary source of infrared radiation is thermal radiation. (heat) • It is the radiation produced by the motion of atoms and molecules in an object. The higher the temperature, the more the atoms and molecules move and the more infrared radiation they produce. • Any object radiates in the infrared. Even an ice cube, emits infrared. • Useful range of IR is from about 2.5 m to 15, 25 or 50 m • Infrared used to determine the major functional groups present. • Quantitative measurements possible but subject to large amount of error. • Atoms or groups of atoms in molecules are in continuous motion with different modes of vibration relative to each other. • Absorption of radiation changes amplitude of vibration but not frequency. 9 • The vibrational IR extends from 2.5 x 10-6 m to 2.5 x 10-5 m (2.5 m -25 m ). – the frequency of IR radiation is commonly expressed in wavenumbers – wavenumber: the number of waves per centimeter, cm-1 (read reciprocal centimeters) – expressed in wavenumbers, the vibrational IR extends from 4000 cm-1 to 400 cm -1 Wavenumber = 1/ -2 -1 n 10 m•cm 2.5 x 10-6 m = 4000 cm -1 n = 10-2 m•cm -1 2.5 x 10-5 m = 400 cm -1 Wave Numbers can be converted to a frequency (n) by multiplying them by the speed of light (c) in cm/sec n (Hz) = n c = c / (cm /sec /cm = 1/sec) Recall: E = h c / Thus, wavenumbers are directly proportional to energy 10 IR Spectroscopy I. Introduction 5. Because the speed of light, c, is constant, the frequency, n, (number of cycles of the wave per second) can complete in the same time, must be inversely proportional to how long the oscillation is, or wavelength: n= c ___ E = hn = hc ___ c = 3 x 1010 cm/s 6. Amplitude, A, describes the wave height, or strength of the oscillation 7. Because the atomic particles in matter also exhibit wave and particle properties (though opposite in how much) EM radiation can interact with matter in two ways: • Collision – particle-to-particle – energy is lost as heat and movement • Coupling – the wave property of the radiation matches the wave property of the particle and “couple” to the next higher quantum mechanical energy level 11 IR Spectroscopy 8. The entire electromagnetic spectrum is used by chemists: Frequency, n in Hz ~1019 ~1017 ~1015 ~1013 ~1010 ~105 0.01 cm 100 m ~10-4 ~10-6 Wavelength, ~.0001 nm ~0.01 nm 10 nm 1000 nm Energy (kcal/mol) > 300 g-rays nuclear excitation (PET) X-rays 300-30 300-30 UV IR Microwave core electronic molecular electron excitation vibration excitation (p to p*) (X-ray cryst.) Visible molecular rotation Radio Nuclear Magnetic Resonance NMR (MRI) 12 ABSORPTION OF IR RADIATION BY MOLECULES • Molecules with covalent bonds may absorb IR radiation. • This absorption is quantized, so only certain frequencies of IR radiation are absorbed. • When radiation, (i.e., energy) is absorbed, the molecule moves to a higher energy state. • The energy associated with IR radiation is sufficient to cause molecules to rotate (if possible) and to vibrate. • If the IR wavelengths are longer than 100 m, absorption will cause excitation to higher rotational states in the gas phase. • If the wavelengths absorbed are between 1 and 100 m, the molecule will be excited to higher vibrational states. • Because the energy required to cause a change in rotational level is small compared to the energy required to cause a vibrational level change, each vibrational change has multiple rotational changes associated with it. 13 Gas phase IR spectra: Consist of a series of discrete lines (a narrow line spectrum) because of Free rotation) Condensed phases. The IR absorption spectrum for a liquid or solid is composed of broad vibrational absorption bands. Molecules absorb radiation when a bond in the molecule vibrates at the same frequency as the incident radiant energy. After absorbing radiation, the molecules have more energy and vibrate at increased amplitude. The frequency absorbed depends on: • The masses of the atoms in the bond. • The geometry of the molecule. • The strength of the bond, • and several other factors. Not all molecules can absorb IR radiation. The molecule must have a change in dipole moment during vibration in order to absorb IR radiation. 14 The types of vibrations available to a molecule are determined by the: • Number of atoms • Types of Atoms • Type of bonding between the atoms As a result, IR absorption spectroscopy is a powerful tool in characterizing pure organic and inorganic compounds. 15 Requirements for the absorption of IR radiation by molecules: 1. The natural frequency of vibration of the molecule must equal the frequency of the incident radiation. 2. The frequency of the radiation must satisfy E = hn, where E is the energy difference between the vibrational states involved. 3. The vibration must cause a change in the dipole moment of the molecule. 4. The amount of radiation absorbed is proportional to the square of the rate of change of the dipole during the vibration. 5. The energy difference between the vibrational energy levels is modified by coupling to rotational energy levels and coupling between vibrations. 16 – Atoms joined by covalent bonds undergo continual vibrations relative to each other – The energies associated with these vibrations are quantized; within a molecule, only specific vibrational energy levels are allowed – The energies associated with transitions between vibrational energy levels for most covalent bonds are from 2 to 10 kcal/mol (8.4 to 42 kJ/mol) – These energies correspond to frequencies in the infrared region between 4000 to 200 cm-1 17 Bond Dipole Moments • In case of polar molecules to differences in electronegativity. • Dipole moment depend on the amount of charge and distance of separation. • Unit in debyes, • = 4.8 x (electron charge) x d(angstroms) 18 Molecular Dipole Moments • Depend on bond polarity and bond angles. • Vector sum of the bond dipole moments. • Lone pairs of electrons contribute to the dipole moment. 19 Dipole moment change • Molecule must have change in dipole moment due to vibration or rotation to absorb IR radiation. • Absorption causes increase in vibration amplitude/rotation frequency • Molecules with permanent dipole moments (µ) are IR active 20 21 Electric field interaction: e.g. HCl The alternating electric field interacts with the changing dipole moment. If the electric vector polarity is positive, it will repel the partial positive charge on the hydrogen atom because like charges repel. Consequently, the hydrogen atom will move away from the electric vector and the H-Cl bond will shorten. Once the polarity of the electric vector changes to being negative, it will attract the hydrogen atom because opposite charges attract. Therefore, the H-Cl bond will get shorter and longer and shorter and longer. During this process, the molecule vibrates at the same frequency as the electric vector, and the energy of the light beam is transferred to the molecule. 22 Hence an infrared absorbance takes place. The IR Spectroscopic Process • The quantum mechanical energy levels observed in IR spectroscopy are those of molecular vibration • We perceive this vibration as heat • When we say a covalent bond between two atoms is of a certain length, we are citing an average because the bond behaves as if it were a vibrating spring connecting the two atoms • For a simple diatomic molecule, this model is easy to visualize: 23 The IR Spectroscopic Process ◦ As a covalent bond oscillates – due to the oscillation of the dipole of the molecule – a varying electromagnetic field is produced ◦ The greater the dipole moment change through the vibration, the more intense the EM field that is generated 24 Infrared Spectroscopy The IR Spectroscopic Process 8. 9. When a wave of infrared light encounters this oscillating EM field generated by the oscillating dipole of the same frequency, the two waves couple, and IR light is absorbed The coupled wave now vibrates with twice the amplitude IR beam from spectrometer “coupled” wave EM oscillating wave from bond vibration 25 Types of Molecular Vibrations (called modes of vibration). • Stretching – change in bond length – Symmetric / asymmetric • bending – change in bond angle – symmetric scissoring – asymmetric wagging – rocking – twisting/torsion 26 The IR Spectroscopic Process 5. There are two types of bond vibration: • Stretch – Vibration or oscillation along the line of the bond H H C C H H asymmetric symmetric • Bend – Vibration or oscillation not along the line of the bond H H H C C C H H scissor rock in plane H H twist C H wag out of plane 27 Molecular vibration of CO2 The asymmetric stretching frequency occurs at 2350 cm-1 and the bending vibration occurs at 666 cm-1. 28 iii.) Types of Molecular Vibrations Bond Stretching symmetric asymmetric 29 Bond Bending In-plane rocking In-plane scissoring Out-of-plane wagging Out-of-plane twisting 30 In some texts: The + sign in the circle indicates movement above the plane of the page toward the reader, while the sign in the circle indicates movement below the plane of the page away from the reader. Bends are also called deformations and the term antisymmetric is used in place of asymmetric in various texts. 31 Theoretical Vibrational Normal modes To locate a point in three-dimensional space requires three coordinates. To locate a molecule containing N atoms in three dimensions, 3N coordinates are required. The molecule is said to have 3N degrees of freedom. To describe the motion of such a molecule, translational, rotational, and vibrational motions must be considered. In a nonlinear molecule: 3 of these degrees are rotational and 3 are translational and the remaining correspond to fundamental vibrations; In a linear molecule: (Linear molecules cannot rotate about the bond axis) 2 degrees are rotational and 3 are translational. The net number of fundamental vibrations: 32 Vibrational modes of H2O (3 atoms –non linear) • Vibrational modes (degrees of freedom) = 3 x 3 - 6= 3 • These normal modes of vibration: • are a symmetric stretch, and asymmetric stretch, and a scissoring • (bending) mode. 33 34 Fundamental Vibrational modes of CO2 (3 atoms –Linear) • Fundamental Vibrational modes (degrees of freedom) = • 3x3–5=4 • These normal modes of vibration: • The asymmetrical stretch of CO2 gives a strong band in the IR at 2350 cm –1 (may noticed in samples due to presence of CO2in the atmosphere). • The two scissoring or bending vibrations are equivalent and therefore, have the same frequency and are said to be degenerate , appearing in an IR spectrum at 666 cm-1. • The difference in behavior of: • Linear Triatomic molecules:Two absorption peaks. • Non linear triatomic molecules:Three absorption peaks. • So illustrates how infrared absorption spectroscopy can sometimes used to deduce molecular shapes. 36 37 Fewer and more experimental peaks than calculated • Fewer peaks – Symmetry of the molecule (inactive) – degenracy • Energies of two or more vibrations are identical • Or nearly identical – Undetectable low absorption intensity – Out of the instrumental detection range • More peaks – Overtone – Combination bands 38 Fundamental Peaks and Overtones • Fundamental transition: • The excitation from the ground state V0 to the first excited state V1 is called the fundamental transition. It is the most likely transition to occur. Fundamental absorption bands are strong compared with other bands that may appear in the spectrum due to overtone, combination, and difference bands. • Overtone bands: • Result from excitation from the ground state to higher energy states V2 , V3 , and so on. • These absorptions occur at approximately integral multiples of the frequency of the fundamental absorption. • If the fundamental absorption occurs at frequency n, the overtones will appear at about 2n, 3n, and so on. • Overtones are weak bands and may not be observed under real experimental conditions. 39 • Coupling modes: • Vibrating atoms may interact with each other. Two vibrational frequencies may couple to produce a new frequency n3 = n1 + n2 . • The band at n3 is called a combination band. • If two frequencies couple such that n3 = n1 - n2 , the band is called a difference band. • Not all possible combinations and differences occur. 40 Rules for Vibrational coupling • Coupling of different vibrations shifts frequencies • Energy of a vibration is influenced by coupling • Coupling likely when – common atom in stretching modes – common bond in bending modes – common bond in bending+stretching modes – similar vibrational frequencies • Coupling not likely when – atoms separated by two or more bonds – symmetry inappropriate We will explain rules of coupling after interpretation IR vibrational theory 41 Classical vibrational motion The stretching frequency of a bond can be approximated by Hooke’s Law. Mechanical model -Two masses -A spring - Simple harmonic motion for single mass Where, y: displacement of mass from its equilibrium position. K: is force constant depends on stiffness of spring -ve sign means that F is a restoring force (that F is opposite to direction of displacemet) 42 Energy of the Hooke’s law (PE of a harmonic Oscillator) At rest eq. position (PE) E = zero. On stretching or compressing of the spring PE = work required to displace the mass. For example moving mass from y to y+dy Work required and so change in PE (dE) = F times distance dy Combined with previous eq. Integration between y=0 and y Gives PE curve for simple harmonic oscilation (A parabola) 43 Harmonic Ocsillator Potential Potential high When the spring is compressed or stretched. Parabola function * E=(1/2)ky2 * Minimum at equilibrium position * Maximum at max amplitude A. 44 Classical vibrational frequency • • • • • Motion of mass as a function of time t: F = ma = m(d2y/dt2) (Newton’s Law) F=-ky m(d2y/dt2) = -Ky-----------------------1 Solution of differential equation (must be a periodic function; its 2nd derivative =to the original function times (-k/m) • A suitable cosine relationship meets this requirement Y = A cos (2pnmt)-------------------------------2 D2y/dt2 = -4p2n2 A cos (2pnmt)-------------------3 where: nm is the vibrational frequency and A the maximum amplitude of the motion Substitution of eq 2 and 3 into eq 1 gives - Ky = A cos (2pnt) K =-4p2n2m m A cos (2pnmt) A cos (2pnt) =(4p2n2m m/K) A cos (2pnmt) 1 nm 2p K m 45 Where nm is the natural frequency depends on: -Force constant of spring -Mass of attached body -Independent on the energy imparted to the system. Change in energy gives a change in amplitude A of the vibration Modification E= hnclass In the classical harmonic oscillator, y is the displacement, the energy or frequency is dependent on how far one stretches or compresses the spring, which can be any value. If this simple model were true, a molecule could absorb energy of any wavelength. So it dose not completely describe the behavior of quantized nature of molecular vibrational E . 46 Quantum treatment of vibrations n: is the vibrational QN takes +ve integer including zero E hn clas h 2p k 47 E hn clas • • • • • • Where n is the wave number of absorption peak in cm-, K is force constant for the bond in N/m, c velocity of light in cm/s and the reduced mass in Kg. K values : For single bonds the range:3x102 to 8x102 with an average of 5x102. For double bond : 1x103. For triple bond : 1.5x103. n n m cn 1 2p Used to estimate n of fundamental absorptions of first excitations. n 1 k 2p c h 2p E Eradiation hn n c 1 2p k h 2p k k cn k 5.3 x10 12 k Q: calculate the aprox. Wave number and wave length of the fundamental absorption peak due to stretching vibration of a carbonyl group. 48 GROUP FREQUENCIES Estimation of frequencies of vibration for various groups possible when force constant known. E.g.1 force constant of C=O bond is 1.23x103 N/m, determine vibrational frequency of this C=O group. 12.0gC 1kgC 1molC x1atomCx = 1.99x 10 26 kgC molC 6.02x 10 23 atomsC 1x 103 gC mO = 2.66x1026 kgO 26 26 mc • • reduced mass of • Substituting: • Units: 1.99x 10 2.67x 10 (1.99 + 2.67)x 10 26 n = 5.3x 10-12 s / cm 1.23x 103 N / m 1.13x 10 -26 kg kg = 1.13x 10 26 kg = 1742 cm-1 N kg m s 2 1 1 s 2 kg m kg m 49 50