Download Lecture 5

Lecture 5:
Power
Original Lecture notes ©
2010 David Money Harris
Modified by Konstantinos
Tatas
Outline
 Power and Energy
 Dynamic Power
 Static Power
7: Power
CMOS VLSI Design 4th Ed.
2
Power and Energy
 Power is drawn from a voltage source attached to
the VDD pin(s) of a chip.
 Instantaneous Power: P(t )  I (t )V (t )
T
 Energy:
E   P (t )dt
0
 Average Power:
7: Power
T
Pavg 
E 1
  P(t )dt
T T 0
CMOS VLSI Design 4th Ed.
3
Power in Circuit Elements
PVDD  t   I DD  t VDD
VR2  t 
PR  t  
 I R2  t  R
R


dV
EC   I  t V  t  dt   C V  t  dt
dt
0
0
VC
 C  V  t dV  12 CVC2
0
7: Power
CMOS VLSI Design 4th Ed.
4
Charging a Capacitor
 When the gate output rises
– Energy stored in capacitor is
2
EC  12 CLVDD
– But energy drawn from the supply is


0
0
EVDD   I  t VDD dt   CL
dV
VDD dt
dt
VDD
 dV  C V
– Half the energy from VDD is dissipated in the pMOS
transistor as heat, other half stored in capacitor
 When the gate output falls
– Energy in capacitor is dumped to GND
– Dissipated as heat in the nMOS transistor
 CLVDD
2
L DD
0
7: Power
CMOS VLSI Design 4th Ed.
5
Switching Waveforms
 Example: VDD = 1.0 V, CL = 150 fF, f = 1 GHz
7: Power
CMOS VLSI Design 4th Ed.
6
Switching Power
T
Pswitching
1
  iDD (t )VDD dt
T 0
T
VDD

iDD (t )dt

T 0
VDD

Tfsw CVDD 
T
 CVDD 2 fsw
VDD
iDD(t)
fsw
C
7: Power
CMOS VLSI Design 4th Ed.
7
Activity Factor
 Suppose the system clock frequency = f
 Let fsw = af, where a = activity factor
– If the signal is a clock, a = 1
– If the signal switches once per cycle, a = ½
 Dynamic power:
Pswitching  a CVDD 2 f
7: Power
CMOS VLSI Design 4th Ed.
8
Short Circuit Current
 When transistors switch, both nMOS and pMOS
networks may be momentarily ON at once
 Leads to a blip of “short circuit” current.
 < 10% of dynamic power if rise/fall times are
comparable for input and output
 We will generally ignore this component
7: Power
CMOS VLSI Design 4th Ed.
9
Power Dissipation Sources
 Ptotal = Pdynamic + Pstatic
 Dynamic power: Pdynamic = Pswitching + Pshortcircuit
– Switching load capacitances
– Short-circuit current
 Static power: Pstatic = (Isub + Igate + Ijunct + Icontention)VDD
– Subthreshold leakage
– Gate leakage
– Junction leakage
– Contention current
7: Power
CMOS VLSI Design 4th Ed.
10
Dynamic Power Example
 200 million transistor chip
– 20M logic transistors
• Average width: 12 l
• Activity factor = 0.1
– 180M memory transistors
• Average width: 4 l
• Activity factor = 0.05
– 1.2 V 100 nm process
– C = 2 fF/mm
– Estimate dynamic power consumption @ 1 GHz.
Neglect wire capacitance and short-circuit
current.
7: Power
CMOS VLSI Design 4th Ed.
11
Solution
2 λ=100 nm => λ = 50 nm = 0.05 μm
Clogic = (20x10^6)(12λ)(0.05μm)(2fF/ μm)= 24 nF
Cmem = (180x10^6)(4λ)(0.05μm)(2fF/ μm)= 72 nF
Pdynamic = (αClogic+ αCmem)(VDD^2)f =
= (0.1•24 nF + 0.05•72 nF )(1.2^2)1 GHz = 8.6 W
7: Power
CMOS VLSI Design 4th Ed.
12
Dynamic Power Example 2
 1 billion transistor chip
– 50M logic transistors
• Average width: 12 l
• Activity factor = 0.1
– 950M memory transistors
• Average width: 4 l
• Activity factor = 0.02
– 1.0 V 65 nm process
– C = 1 fF/mm (gate) + 0.8 fF/mm (diffusion)
 Estimate dynamic power consumption @ 1 GHz.
Neglect wire capacitance and short-circuit current.
7: Power
CMOS VLSI Design 4th Ed.
13
Dynamic Power Reduction
2
P

a
CV
 switching
DD f
 Try to minimize:
– Activity factor
– Capacitance
– Supply voltage
– Frequency
7: Power
CMOS VLSI Design 4th Ed.
14
Activity Factor Estimation
 Let Pi = Prob(node i = 1)
– Pi = 1-Pi
 ai = Pi * Pi
 Completely random data has P = 0.5 and a = 0.25
 Data is often not completely random
– e.g. upper bits of 64-bit words representing bank
account balances are usually 0
 Data propagating through ANDs and ORs has lower
activity factor
– Depends on design, but typically a ≈ 0.1
7: Power
CMOS VLSI Design 4th Ed.
15
Switching Probability
7: Power
CMOS VLSI Design 4th Ed.
16
Example
 A 4-input AND is built out of two levels of gates
 Estimate the activity factor at each node if the inputs have P =
0.5
 Calculate the dynamic power consumption assuming the
transistor data of Example 1
7: Power
CMOS VLSI Design 4th Ed.
17
Clock Gating
 The best way to reduce the activity is to turn off the
clock to registers in unused blocks
– Saves clock activity (a = 1)
– Eliminates all switching activity in the block
– Requires determining if block will be used
7: Power
CMOS VLSI Design 4th Ed.
18
Capacitance
 Gate capacitance
– Fewer stages of logic
– Small gate sizes
 Wire capacitance
– Good floorplanning to keep communicating
blocks close to each other
– Drive long wires with inverters or buffers rather
than complex gates
7: Power
CMOS VLSI Design 4th Ed.
19
Voltage / Frequency
 Run each block at the lowest possible voltage and
frequency that meets performance requirements
 Voltage Domains
– Provide separate supplies to different blocks
– Level converters required when crossing
from low to high VDD domains
 Dynamic Voltage Scaling
– Adjust VDD and f according to
workload
7: Power
CMOS VLSI Design 4th Ed.
20
Static Power
 Static power is consumed even when chip is
quiescent.
– Leakage draws power from nominally OFF
devices
– Ratioed circuits burn power in fight between ON
transistors
7: Power
CMOS VLSI Design 4th Ed.
21
Static Power Example
 Revisit power estimation for 1 billion transistor chip
 Estimate static power consumption
– Subthreshold leakage
• Normal Vt:
100 nA/mm
• High Vt:
10 nA/mm
• High Vt used in all memories and in 95% of
logic gates
– Gate leakage
5 nA/mm
– Junction leakage
negligible
7: Power
CMOS VLSI Design 4th Ed.
22
Solution
Wnormal-Vt   50 106  12l  0.025m m / l  0.05   0.75 106 m m
Whigh-Vt   50 106  12l  0.95    950 106   4l    0.025m m / l   109.25 106 m m
I sub  Wnormal-Vt 100 nA/m m+Whigh-Vt 10 nA/m m  / 2  584 mA


I gate   Wnormal-Vt  Whigh-Vt  5 nA/m m  / 2  275 mA


Pstatic   584 mA  275 mA 1.0 V   859 mW
7: Power
CMOS VLSI Design 4th Ed.
23
Subthreshold Leakage
 For Vds > 50 mV
Vgs  Vds VDD   k Vsb
I sub  I off 10
S
 Ioff = leakage at Vgs = 0, Vds = VDD
7: Power
Typical values in 65 nm
Ioff = 100 nA/mm @ Vt = 0.3 V
Ioff = 10 nA/mm @ Vt = 0.4 V
Ioff = 1 nA/mm @ Vt = 0.5 V
 = 0.1
k = 0.1
S = 100 mV/decade
CMOS VLSI Design 4th Ed.
24
Stack Effect
 Series OFF transistors have less leakage
– Vx > 0, so N2 has negative Vgs
 Vx VDD 
I sub  I off 10
S
 I off 10
Vx   VDD Vx  VDD   k Vx
S
N2
Vx 
N1
VDD
1  2  k
I sub  I off 10
 1  k
VDD 
 1 2  k

S




 I off 10
VDD
S
– Leakage through 2-stack reduces ~10x
– Leakage through 3-stack reduces further
7: Power
CMOS VLSI Design 4th Ed.
25
Leakage Control
 Leakage and delay trade off
– Aim for low leakage in sleep and low delay in
active mode
 To reduce leakage:
– Increase Vt: multiple Vt
• Use low Vt only in critical circuits
– Increase Vs: stack effect
• Input vector control in sleep
– Decrease Vb
• Reverse body bias in sleep
• Or forward body bias in active mode
7: Power
CMOS VLSI Design 4th Ed.
26
Gate Leakage
 Extremely strong function of tox and Vgs
– Negligible for older processes
– Approaches subthreshold leakage at 65 nm and
below in some processes
 An order of magnitude less for pMOS than nMOS
 Control leakage in the process using tox > 10.5 Å
– High-k gate dielectrics help
– Some processes provide multiple tox
• e.g. thicker oxide for 3.3 V I/O transistors
 Control leakage in circuits by limiting VDD
7: Power
CMOS VLSI Design 4th Ed.
27
NAND3 Leakage Example
 100 nm process
Ign = 6.3 nA
Igp = 0
Ioffn = 5.63 nA Ioffp = 9.3 nA
Data from [Lee03]
7: Power
CMOS VLSI Design 4th Ed.
28
Junction Leakage
 From reverse-biased p-n junctions
– Between diffusion and substrate or well
 Ordinary diode leakage is negligible
 Band-to-band tunneling (BTBT) can be significant
– Especially in high-Vt transistors where other
leakage is small
– Worst at Vdb = VDD
 Gate-induced drain leakage (GIDL) exacerbates
– Worst for Vgd = -VDD (or more negative)
7: Power
CMOS VLSI Design 4th Ed.
29
Power Gating
 Turn OFF power to blocks when they are idle to
save leakage
– Use virtual VDD (VDDV)
– Gate outputs to prevent
invalid logic levels to next block
 Voltage drop across sleep transistor degrades
performance during normal operation
– Size the transistor wide enough to minimize
impact
 Switching wide sleep transistor costs dynamic power
– Only justified when circuit sleeps long enough
7: Power
CMOS VLSI Design 4th Ed.
30