Download Electrical Power System SMJE 2103

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Three-phase electric power wikipedia , lookup

Electrical substation wikipedia , lookup

Voltage optimisation wikipedia , lookup

Decibel wikipedia , lookup

Power factor wikipedia , lookup

Standby power wikipedia , lookup

Wireless power transfer wikipedia , lookup

Electrification wikipedia , lookup

Audio power wikipedia , lookup

Mains electricity wikipedia , lookup

Distribution management system wikipedia , lookup

Electric power system wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Amtrak's 25 Hz traction power system wikipedia , lookup

History of electric power transmission wikipedia , lookup

Alternating current wikipedia , lookup

Power over Ethernet wikipedia , lookup

AC adapter wikipedia , lookup

Power engineering wikipedia , lookup

Transcript
Electrical Power System
SMJE 2103
Electrical Power
Delivery System
Power Flow / Load Flow
• A numerical analysis for future planning of
operational power system in order to optimize
generated power.
• The objective is to produce following inform:
i- voltage magnitude and phase angle at each
bus
ii- real and reactive power flowing in each
element
iii- reactive power loading on each generator
Power Delivery
“Overhead Lines - Components”
Power Delivery
“Transmission Line – Single Line”
Power Delivery
“Towers - types”
Power Delivery
“Towers - size”
Height of tower is determine by-
H  h1  h2  h3  h4
h1=Minimum permissible ground clearance
h2=Maximum sag
h3=Vertical spacing between conductors
h4=Vertical clearance between earthwire and
top conductor
Power Delivery
“Conductor - types”

ACSR Conductor(Aluminium Conductor Steel Reinforced)

AAC(All Aluminium Conductor)

AAAC(All Alloy Aluminium Conductor)
Power Delivery
“Line – equivalent circuit”
L’ = Inductance
R’ = Resistance
C’ = Capacitance
G’ = Leakage Resistance
Power Delivery
“Conductor - resistance”
- Short line (up to 80 km)
- Medium-length lines (up to 240 km)
- Long line (above 240 km)
Power Delivery
“Transmission Line”
Power Delivery
“Power Cable”
Power Delivery
“Power Cable”
Power Delivery
“Power Cable - losses”
Power Delivery
“Power Cable - losses”
Dielectric used for cable insulation must have following
properties:
•
•
•
•
•
•
High insulation resistance
High dielectric strength
Good mechanical strength
Immune to attack by acids and alkali in the range 0-100o C
Should not be too costly
Should no be hygroscopic (tending to absorb water), or if
hygroscopic should be enclosed in a water tight covering
Power Delivery
“Cable - resistance”
Power Delivery
“Cable - inductance”
Power Delivery
“3- Core Cable - inductance”
Power Delivery
“3- Core Cable – inductance (M & C)”
Power Delivery
“3- Core Cable – inductance”
(Measured)
Power Delivery
“3- Core Cable - inductance”
(Measured)
Example/Tutorial
• A 3 core, 3 phase metal sheathed cable on testing for
the capacitance gave the following results:
i) Capacitance between all conductors bunched and
sheath, Cm1=0.6uF
ii) Capacitance between two conductor bunched with
sheath and third conductor, Cm2=0.36 uF
With the sheath insulated find,
a) Capacitance between any two conductors
b) Capacitance to neutral
c) Charging current if cable is connected to 11kV, 3
phase, 50 Hz system
Power Delivery
“3- Core Cable – Gas-pressure”
Power Delivery
“3- Core Cable – Gas-pressure”
Power Delivery
“3- Core Cable – Gas-pressure”
Power Delivery
“Insulator”
Power Delivery
“Insulator - Types”
There are several types of insulators
but the most commonly used are :
1)Pin Insulator
2)Suspension Insulator
3)Strain Insulator and
4)Shackle insulator.
Power Delivery
“Pin Insulator”
- Nonconducting material such as porcelain, glass,
plastic, polymer, or wood.
- Upto 33 kV
Power Delivery
“Pin Insulator”
Power Delivery
“Suspension Insulator”
- For high voltages (>33 kV)
- Each unit or disc is designed for low voltage, say 11 kV
- The number of discs in series would obviously depend upon
the working voltage
Power Delivery
“Suspension Insulator”
Power Delivery
“Strain Insulator”
- Dead end of the line or corner or sharp curve.
- For low voltage lines (< 11 kV).
- Two or more strings are used in parallel.
Power Delivery
“Strain Insulator”
Power Delivery
“Shackle Insulator”
- Used for low voltage distribution lines.
- Horizontal or vertical position.
Power Delivery
“Shackle Insulator”
Power Delivery
“Insulator”
Power Delivery
“Circuit Breaker”
Power Delivery
“Circuit Breaker”
Power Delivery
“Circuit Breaker”
Power Delivery
“Circuit Breaker”
Power Delivery
“Circuit Breaker”
Power Delivery
“Switchgear (GIS)”
Power Delivery
“Switchgear (GIS)”
Power Delivery
“Switchgear (GIS)”
Power Delivery
“Switchgear (GIS)”