Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Computer network wikipedia , lookup
Network tap wikipedia , lookup
Recursive InterNetwork Architecture (RINA) wikipedia , lookup
Parallel port wikipedia , lookup
List of wireless community networks by region wikipedia , lookup
Point-to-Point Protocol over Ethernet wikipedia , lookup
Piggybacking (Internet access) wikipedia , lookup
Zero-configuration networking wikipedia , lookup
English version Sweex Broadband Router + 4 ports 10/100 switch English version Possible applications You can easily create an Internet-sharing network for several users without having to install any other software or make any complicated adjustments. A standard built-in PAT,NAT Firewall protects you against external users who want to sniff around inside your PC. Note: Installing a Firewall software is recommended. Quick Configuration installation for Windows 95, 98 and ME Advantages Internet Sharing - if you have a broadband Internet connection, you can enable several PC’s to simultaneously access the Internet. Supports DHCP Server/Client - Ideal for fast installation, user-friendly configuration (support for DHCP server/client support) 4 ports 10/100 Switch - Create a network and share the Internet with several users. Dial on Demand - the router automatically logs-in to the ISP when you start the browser. Firewall protection from Intranet. To configure the router, the PC requires a few basic settings, which you can make as follows: Right-click on Network Environment and click on Properties’. The ‘Network configuration screen’ will appear. If you have a modem in your computer, the screen will also show TCP/IP in front of the dialling adapter, as well as a NetBEUI. Salient characteristics • • • • • • • • Standard IEEE 802.3. 10Base-T, 100Base-TX 10/100 Mbps speed 4 RJ-45 Ports MDI-X - WAN/Uplink Port MDI-II - Uplink/WAN Port WEB Based Management GUI - with this you can get fast access to change the router configuration. Supports PPPoE and PPTP clients for xDSL connections. Support for IPRouting and NAT/PAT Technical Specifications • • • • • WAN Port DMZ redirect WAN port’s Public IP addresses to LAN Private IP addresses Address Mapping Virtual Servers Bridge Mode Now click on the TCP/IP of your network card and after entering an IP address, click on ‘Automatic to get an IP address automatically’. Access control and protection • • • • • • NAT firewall - there is no access to the private IP addresses over the Internet IP Packet Access Control Hacker Attack protection (DoS) PAP/CHAP/MS-CHAP authentications VPN PPTP Client VPN /PPTP/IPSec pass through Monitoring • DHCP Client Log • Security Log • Device/Connection Status Management • Web-Based Management • Remote Management W W W. S W E E X . C O M Now connect your broadband router to the computer with a straight cable to the network card. Go the Start menu and select ‘Run’, enter the command’winipcfg’ (without quotation marks) and under adapter information, select the network card that you have. English version The IP configuration address is in xxx.xxx.xxx.xxx, now click Clear All and the IP configuration address will change to 0.0.0.0 English version Quick Configuration installation for Windows 2000 XP To configure the router, the PC requires a few basic settings, which you can make as follows: Right-click on Network Environment and click on Properties’. The ‘Network configuration screen’ will appear. Select the option Internet protocol (TCP/IP) and click on OK. Now click Refresh All. The Router will assign the IP-address. Select the option Automatic to obtain an IP address and click OK. This completes the basic settings for Windows 95, 98 and ME. To connect to the Internet go to the Router Configuration chapter further on in this manual. The attached CD-Rom provides further information concerning router applications. Do not enter any of the commands with inverted commas!! Now go to the start menu then to ‘Run’ and tick-mark CMD and press Enter. Enter the command Ipconfig and press Enter. Now give the command Ipconfig /release’and press ‘Enter. W W W. S W E E X . C O M English version English version WAN Port Straight Twisted PairCable Crossover Cable MDI-X Standard modem port This has an Uplink function MDI-II This has an Uplink function Standard modem port RESET The IP address will now be replaced. You will see that the IP address is now 0.0.0.0. Now enter the command Ipconfig /renew and press Enter. LAN MDI-II MDI-X All the cables used are standard Cat5 Twisted Pair. ATTENTION!! When you execute the following, all the data that you have entered in the router get deleted and it means that you have to enter the login name, password, MAC address and IP addresses. To reset the router fully, keep the reset button pressed down with a pencil for four seconds. The LAN LED’s 1 to 4 shall light-up once, simultaneously, to indicate that resetting has been completed. The settings of the router will now have been reset to the ‘factory default’ settings. The router will now assign a new IP address. If you press the reset button once, the router will be reset in the normal manner and the entered data will generally not be deleted. Application diagram LED Status PWR WAN 10/100M Power On Reset LAN 10/100M On LAN LNK/ACT (Port 1-4) ADSL or Cable Modem Computer Computer Computer Depending on the type of modem you are using, select MDI-II of MDI-X.When the left LED lights up on the router, it means that the port selected is correct and you can proceed with the installation. W W W. S W E E X . C O M The 10Mbps WAN port is connected The WAN port is connected (LNK) Off No WAN connection Flashing There is activity in the WAN port (ACT), data is being sent Off LAN port 10Mbps is connected Off No LAN connection Flashing There is activity in the LAN port (ACT) data is being sent On (Port 1-4) The power supply to the router is switched-on The 100Mbps WAN port is connected Off WAN LNK/ACT Switch/Hub description On The 100Mbps LAN port is connected On LAN port is connected (LNK) English version English version Router Configuration You can connect to the Internet after completing the network configuration of your computer. Start your browser, enter the following address in the URL bar: http://192.168.2.1 Now press Enter. Here fill-in the time zone, and if you want you may enter the summertime and wintertime information. Click on Next to start the procedure. Click Login without entering anything in the field. • • • • Cable Modem Fixed-IP xDSL PPPoE PPTP Your ISP will automatically give you an IP address You have received a fixed IP address from your ISP. Your ISP is working via a Point-to-Point Protocol over Ethernet (PPPoE) connection. Your ISP is working via a Point-to-Point Tunneling Protocol (PPTP) connection. Select the type of connection, for example we may try to make a PPPoE connection. Select PPPoE xDSL and you will be automatically referred to the correct field. Click on Quick Setup W W W. S W E E X . C O M English version Enter your user name and password. Fill in the MTU value 1492, then click OK to store the data. When you see this window, it means that the data has been saved, and you can now click on LogOut to come back to the login screen, where you should click on Cancel. Your computer is ready to access the Internet over the router after you restart it. W W W. S W E E X . C O M