* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download b. Noise in Analog March 2013 - Classes
Wien bridge oscillator wikipedia , lookup
Spectrum analyzer wikipedia , lookup
Power MOSFET wikipedia , lookup
Radio transmitter design wikipedia , lookup
Transistor–transistor logic wikipedia , lookup
Schmitt trigger wikipedia , lookup
Power electronics wikipedia , lookup
Charge-coupled device wikipedia , lookup
Immunity-aware programming wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Opto-isolator wikipedia , lookup
Operational amplifier wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Telecommunication wikipedia , lookup
Analog-to-digital converter wikipedia , lookup
Rectiverter wikipedia , lookup
Index of electronics articles wikipedia , lookup
Valve audio amplifier technical specification wikipedia , lookup
Noise in Analog CMOS ICs Gábor C. Temes School of Electrical Engineering and Computer Science Oregon State University March 2013 [email protected] 1/25 Noise = Unwanted Signal • Intrinsic (inherent) noise: – generated by random physical effects in the devices. • Interference (environmental) noise: – coupled from outside into the circuit considered. • Switching noise: – charge injection, clock feedthrough, digital noise. • Mismatch effects: – offset, gain, nonuniformity, ADC/DAC nonlinearity errors. • Quantization (truncation) “noise”: – in internal ADCs, DSP operations. [email protected] 2/25 Purpose and Topics Covered • Purpose: Fast Estimation of Noise in Analog Integrated Circuits Before Computer Simulation. Topics Covered: • The Characterization of Continuous and Sampled Noise; • Thermal Noise in Opamps; • Thermal Noise in Feedback Amplifiers; • Noise in an SC Branch; • Noise Calculation in Simple SC Stages; • Sampled Noise in Opamps. [email protected] 3/25 Characterization of Continuous-Time Random Noise – (1) • Noise x(t) – e.g., voltage. Must be stationary as well as mean and variance ergodic. • Average power defined as mean square value of x(t): 1 T 2 Pav lim x (t )dt E x 2 (t ) T T 0 • For uncorrelated zero-mean noises E{x1 x2 } E{x12 } E{x22 } 2 • Power spectral density (PSD) Sx(f) of x(t): Pav contained in a 1Hz BW at f. Hence dPav = Sx(f).df . Measured in V2/Hz. Even function of f. • Filtered noise: if the filter has a voltage transfer function H(s), the output noise PSD is |H(j2pf)2|Sx(f). [email protected] 4/25 Characterization of Continuous-Time Random Noise – (2) • Average power in f1 < f < f2: f2 Pf1 , f 2 S x ( f )df f1 Here, Sx is regarded as a one-sided PSD. Hence, P0, Pav. So white noise has infinite power!? NO. Quantum effects occur when h.f ~ kT. Here, h is the Planck constant. This occurs at tens of THz; parasitics will limit noise much before this! • Amplitude distribution: probability density function(PDF) px(x). px(x1)Dx: probability of x1 < x < x1+Dx occurring. E.g., px(q)=1/LSB for quantization noise q(t) if |q| < LSB/2, 0 otherwise. Gaussian for thermal noise, often uniform for quantization noise. [email protected] 5/25 Characterization of Sampled-Data Random Noise • Noise x(n) – e.g., voltage samples. • Ave. power: 1 N Pav E lim x(n) 2 N N 1 n0 Pav is the mean square value of x(n). • For sampled noise, Pav remains invariant! • Autocorrelation sequence of x(n) – shows periodicities! rx (k ) E{x(n) x(n k )} rx (0) Pav of x(n) E{ x(n) } 2 • PSD of x(n): Sx(f) = F [rx(k)]. Periodic even function of f with a period fc. Real-valued, non-negative. f • Power in f1 < f < f2: Pf , f S x ( f )df 2 1 Pav fc / 2 2 f1 S x ( f )df P0, f x / 2 E{ x(n) } 2 Sampled noise has finite power! • PDF of x(n): px(x), defined as before. 0 [email protected] 6/25 Thermal Noise – (1) Due to the random motion of carriers with the MS velocity ∝ T. Dominates over shot noise for high carrier density but low drift velocity, occurring, e.g., in a MOSFET channel. Mean value of velocity, V, I is 0. The power spectral density of thermal noise is PSD = kT. In a resistive voltage source the maximum available noise power is hence ____ 2 E k T BW 4 R giving ____ 2 E 4 k T BW R k: Boltzmann constant, 1.38x10^-23 J/K [email protected] 7/25 Thermal Noise – (2) The probability density function of the noise amplitude follows a Gaussian distribution ____ p( E ) e E 2 / E 2 ____ 2 E 2p ____ 2 Here, E is the MS value of E. In a MOSFET, if it operates in the triode region, R=r can be used in the drain-source branch. In the active region, averaging over the tapered channel, R=(3/2)/gm results. The equivalent circuit is __________ 2 E (f) 8kT ( PSD) gm [email protected] 8/25 Noise Bandwidth Let a white noise x(t) with a PSD Sx enter an LPF with a transfer function: H (s) G0 s 3dB 1 Here G0 is the dc gain, and 3-dB is the 3-dB BW of the filter. The MS value of the output noise will be the integral of |H|2. Sx, which gives ___ 2 x 3dB 4 G02 S x Assume now that x(t) is entered into an ideal LPF with the gain function: |H|=G0 if f < fn and 0 if f > fn. The MS value of the output will then be: ___ 2 x f n G02 S x Equating the RHSs reveals that the two filters will have equivalent noise transfer properties if fn 3 dB 4 p 2 f 3 dB Here, fn is the noise bandwidth of the LPF. [email protected] 9/25 Analysis of 1/f Noise in Switched MOSFET Circuits • 1/f noise can be represented as threshold voltage variation. • If the switch is part of an SC branch, it is unimportant. In opamps,it is critical! • In a chopper or modulator circuit, it may be very important. See the TCAS paper shown. [email protected] 10/25 Thermal Op-Amp Noise – (1) Simple op-amp input stage [3]: 2 ni With device noise PSD: V (8 / 3)kT / gmi 16 kT g 16 kT 2 V Equivalent input noise PSD: neq ( f ) 3 g 1 gm3 3 g V 2 / Hz m1 m1 m1 for gm1 >> gm3. It can be represented by a noisy resistor RN = (8/3)kT/gm1 at one input terminal. Choose gm1 as large as practical! All noises thermal - white. Opamp dynamics ignored. [email protected] 11/25 Thermal Op-Amp Noise – (2) All devices in active region, [id(f)]2=(8/3)kT·gm. Consider the short-circuit output current I0,sh of the opamp. The output voltage is Io,sh·Ro. If the ith device PSD is considered, its contribution to the PSD of I0,sh is proportional to gmi. Referring it to the input voltage, it needs to be divided by the square of the input device gm, i.e, by gm12. Hence, the input-referred noise PSD is proportional to gm/gm12. For the noise of the input device, this factor becomes 1/gm1. Conclusions: Choose input transconductances (gm1) as large as possible. For all non-input devices (loads, current sources, current mirrors, cascade devices) choose gm as small as possible! [email protected] 12/25 Noisy Op-Amp with Compensation Op-amp has thermal input noise PSD Pni = 16kT/3gm1, where gm1 is the transconductance of the input devices. Single-pole model; voltage gain A(s) = A03-dB/(s+3-dB), where A0 is the DC gain, 3-dB is the 3-dB BW (pole frequency), and u=A03-dB is the unity-gain BW of the op-amp. For folded-cascode telescopic and 2-stage OTAs, usually u=gm1/C, where C is the compensation capacitor. Open-loop noise BW is fn = gm1/4A0C, and the open-loop noise gain at DC is A0. Hence, the open-loop output noise power is Pon 4 A kT 16 kT 2 g m1 A0 0 . 3 g m1 4 A0C 3C [email protected] 13/25 Noisy Op-Amp with Unity-Gain Feedback If the op-amp is in a unity-gain configuration, then (for A0>>1) the noise bandwidth of the stage becomes A0fn, and the DC noise gain is 1. Hence, the output (and input) thermal noise power is 16kT g m1 4kT Pn , 3 g m1 4C 3C (This result is very similar to the kT/C noise power formula of the simple R-C circuit!) Vo Vin Vn [email protected] 14/25 Noisy Op-Amp in an SC Gain Stage A more general feedback stage: Y2 Y1 VinVin+ Vo Vn Let Gi=Y1/Y2 be constant. Then the noise voltage gain is the singlepole function An (s) Von (s) / Vn (s) u /( s 3dB ) where 3dB u /(1 Gi ) is the 3-dB frequency of An(j). The DC noise gain is u / 3dB 1 Gi , and the noise BW of the stage is f n g m1 /[ 4C (1 Gi )]. Hence, the output thermal noise power is Pno g / 4C 4(1 Gi )kT 16kT (1 Gi ) 2 m1 , 3g m1 1 Gi 3C and the input-referred thermal noise power is Pni = (4/3) kTb/C, where b = 1/(Gi+1 ) is the feedback factor. Pni is smaller for a higher gain Gi, so a higher SNR is possible for higher stage gain. [email protected] 15/25 Switched-Capacitor Noise – (1) Two situations; example: in C-T AAF SCF ADC DSP DAC Sit. 1 SCF C-T RCF out Sit. 2 Situation 1: only the sampled values of the output waveform matter; the output spectrum may be limited by the DSP, and hence VRMS,n is reduced. Find VRMS from kTC charges; adjust for DSP effects. Noise can be estimated by hand analysis. Situation 2: the complete output waveform affects the SNR, including the S/H and direct noise components. Usually the S/H noise dominates at low frequencies. High-frequency noise is reduced by the reconstruction filter. Needs CAD analysis. [email protected] 16/25 Sampling Noise [email protected] 17/25 Switched-Capacitor Noise Thermal noise in a switched-capacitor branch: (a) circuit diagram; (b) clock signal; (c) output noise; (d) direct noise component; (e) sampled-and-held noise component. The noise power is kT/C in every time segment. [email protected] 18/25 Switched-Capacitor Noise Spectra For f << fc, SS/H >> SD . Sampled PSD = 2kT/fsC ; the unsampled PSD = 4kTRon. Their ratio is 1/(2fs.Ron.C) >> 1 !! Sampling penalty. [email protected] 19/25 Switched-Capacitor Noise The MS value of samples in VcnS/H is unchanged: V S/H 2 cn kT / C Regarding it as a continuous-time signal, at low frequency its one-sided PSD is S S/H 2(1 m) 2 kT (f) f cC while that of the direct noise is mkT , f swC 2(1 m) 2 f sw . m fc Sd ( f ) S S/H Sd Since we must have fsw/fc > 2/m, usually |SS/H| >> |Sd| at low frequencies. (See also the waveform and spectra.) See Gregorian-Temes book, pp. 505-510 for derivation. [email protected] 20/25 Calculation of SC Noise – (1) In the switch-capacitor branch, when the switch is on, the capacitor charge noise is lowpass-filtered by Ron and C. The resulting charge noise power in C is kTC. It is a colored noise, with a noisebandwidth fn = 1/(4·Ron ·C). The low-frequency PSD is 4kTRon. When the switch operates at a rate fc<<fn, the samples of the charge noise still have the same power kTC, but the spectrum is now white, with a PSD = 2kTC/fc. For the situation when only discrete samples of the signal and noise are used, this is all that we need to know. For continuous-time analysis, we need to find the powers and spectra of the direct and S/H components when the switch is active. The direct noise is obtained by windowing the filtered charge noise stored in C with a periodic window containing unit pulses of length m/fc. This operation (to a good approximation) simply scales the PSD, and hence the noise power, by m. The low-frequency PSD is thus 4mkTRon. For complex circuits, CAD is required to find noise. [email protected] 21/25 Calculation of SC Noise (summary) – (2) To find the PSD of the S/H noise, let the noise charge in C be sampledand-held at fc, and then windowed by a rectangular periodic window w(t)=0 for n/fc < t< n/fc+m/fc w(t)=1 for n/fc+m/fc < t < (n+1)/fc n= 0, 1, 2, … Note that this windowing reduces the noise power by (1 - m) squared(!), since the S/H noise is not random within each period. Usually, at low frequencies the S/H noise dominates, since it has approximately the same average power as the direct noise, but its PSD spectrum is concentrated at low frequencies. As a first estimate, its PSD can be estimated at 2(1-m)2kT/fc·C for frequencies up to fc/2. [email protected] 22/25 Circuit Example: Lossy Integrator with Ideal Op-Amp[4] RMS noise charge delivered into C3 as f2→0, assuming OTA: From C1: Form C2: RMS noise charges acquired by Ci during f1 = 1: qij Ci kT / Ci kTCi , i, j 1,2 with Vin set to 0. C3 C2 C3 2 C3 CC kT 2 3 q2 (kTC2 ) C2 C3 C2 C3 C3 C2 q3 kT 2C1 2C2 2 C2 C3 C3 Total: fia: advanced cutoff phase q1 2kTC1 1/ 2 1/ 2 Input-referred RMS noise voltage: Vin,n C C3 kT q3 2 C1C3 C1 Vin,n C22 2 C 2 C 2 1 C3 1/ 2 1 kT (C1 C2 ) for C2 C3 . C1 Vin,n and Vin are both low-pass filtered by the stage. [email protected] 23/25 Sampled Op-Amp Noise Example [4] • f1=1 Direct noise output voltage = Vneq • f2=1 Charges delivered by C1 and C2: -C1(Vneq+Vin)+C2(V0-Vneq). Charge error –(C1+C2)Vneq. • Input-referred error voltage Vneq(1+C2/C1). [email protected] 24/25 Reference [email protected] 25/25