* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download ML-BB60-NW - M-Elec Superior Lighting
Power inverter wikipedia , lookup
Three-phase electric power wikipedia , lookup
Wireless power transfer wikipedia , lookup
Voltage optimisation wikipedia , lookup
Standby power wikipedia , lookup
Electric power system wikipedia , lookup
History of electric power transmission wikipedia , lookup
Buck converter wikipedia , lookup
Amtrak's 25 Hz traction power system wikipedia , lookup
Phone connector (audio) wikipedia , lookup
Audio power wikipedia , lookup
Electrification wikipedia , lookup
Alternating current wikipedia , lookup
Power engineering wikipedia , lookup
Power over Ethernet wikipedia , lookup
Mains electricity wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Industrial and multiphase power plugs and sockets wikipedia , lookup
BB60 ML-BB60-NW TECHNICAL DETAILS INCLUDED IN THE BOX 1 x LED ML-BB60-NW 1 x Inbuilt driver SCAN TO VIEW ONLINE Total power consumption: 12W / 24W switchable Lumen | power: 1125lm | 12W 2100lm | 24W Colour output: 4500K - Neutral White IP rating: IP20 CRI: 80+ Dimmable: Yes Beam angle: 120 degrees Average life: 30,000 hrs* Power supply: AC 240V±10%, 50-60Hz (inbuilt driver) Length: 614 mm | Width: 74 mm | Height: 67 mm Housing: White Warranty: 3 years (4 years for PLI) ADDITIONAL OPTIONS: infinity X joiner (ML-BB-JN), diffuser (ML-BB-D60), suspension kit (ML-BB-SUS) * Average life is calculated on expected life span. 5 INSTALLATION INSTRUCTIONS INSTALLATION: 1. Before commencing installation or maintenance, ensure electricity is switched off at the mains 2. By pressing side tabs on the fitting sides IN separate the “top” of the fitting from the “base“ 3. Using screws fix the “base” onto the required location 4. Wire up the fitting according to the marked terminals. 5. Set the driver switch to desired setting: Single/Twin mode (picture 3). Default driver setting is Twin mode. 6. Connect the push connector to the driver ensuring polarity is correct. 7. Snap the “top“ onto the “base” to its original position (picture 4). Make sure all 4 spring connectors are in place securely holding “top“ in place. 8. Once completed and safe the power can be restored (for dimming refer to our web site). Picture 1 PUSH CONNECTOR Picture 2 Line - L Earth - E Neutral - N Picture 3 Picture 4 SPRING CONNECTORS WILL HOLD FITTING IN PLACE | SINGLE MODE Power: 12W Lumen: 1125lm || TWIN MODE Power: 24W Lumen: 2100lm BB60 ML-BB60-NW PLEASE NOTE • • • • • • • • • • • MUST BE INSTALLED BY A LICENSED ELECTRICIAN Do not extend low voltage cables from the output of power supply All components must not be mechanically stressed Be careful to not damage or destroy conducting paths on the circuit board Follow all relevant electrical and safety standards (including AS3000) – only qualified personnel should be allowed to perform installations Correct electrical polarity needs to be observed as the wrong polarity may destroy the lights which is not covered under warranty Damaged by corrosion will not be honoured as a materials defect claim. It is the user’s responsibility to provide suitable protection against corrosive agents such as moisture, condensation and other harmful elements For indoor use only. Do not touch luminaire with a wet hand or cloth. If these regulations are not followed warranty will be void and all issues are the responsibility of the electrician. For further information including photometrics & dimming range, please visit www.melec.com.au FEATURES Spring connectors Power change switch 1 hand push connector holding fitting in place Conduit entry cut out Large cable entry 2 piece assembly Extra large terminal block Plenty of fixing points Tear-out end caps ACCESSORIES Full DIFFUSER ML-BB-D60 Infinity X joiner ML-BB-JN Suspension kit ML-BB-SUS