Download LP7000 Specifications

LP7000
Specifications
Specifications
System
Overall dimensions
See Dimensions.
Processing speed
1638 mm/minute
Heating capacity
About 0.453 kW (about 390 kcal/h)
Printer processor section
Weight
Approx. 301.7±3 Kg
Exposure conditions
Controlled with the built-in colorimeter.
Operati
on
section
Display module
Exposure engine
iBeam Engine
The flatbed scanner recommended by us*1, which is used at iBeam Engine
setup, is necessary.
To know more about the flatbed scanner, please consult your technical
representative.
*1. For the suitable flatbed scanner models, see Flatbed scanner
(recommended) as explained later.
Print resolution
Main scanning:
Sub-scanning:
300 dpi
300 dpi
Exposure speed
27.94 mm/second
Exposure system
Exposure scanning via paper advance
Print size
Paper width:
Paper advance length:
89, 102, 114, 117, 120, 127, 130, 152, 165, 178, and 203 (mm)
from 82.5 to 610.0 mm
Paper supply
Single magazine type (Dual magazine type and triple magazine type are
factory options.)
Paper specification
Maximum diameter of paper roll: 250 mm
Transport system
Roller transport system
Temperature control
Temperature in each sub-tank is controlled separately.
Replenishment system
The system calculates the processed amount of paper surface based on the
print size and automatically supplies the appropriate amount of replenisher
to each tank.
Water refilling
Water refilling is performed automatically when the solution level sensors
are activated.
Automatic cleaning
The upper guides are automatically cleaned at close down checks.
1
Processing tank capacity
• Color Developer
8.5 liters
• Bleach Fixer
8.2 liters
• Stabilizer
11.6 liters
Processing time
• Color Developer
22.3 sec (31.1 sec)*1
• Bleach Fixer
27.1 sec (37.8 sec)*1
• Stabilizer
43.1 sec (60.1 sec)*1
• Dryer
14.5 sec (20.2 sec)*1
*1. Processing time required for some types of paper
Processing temperature
• Color Developer
42±0.3°C
• Bleach Fixer
40±2.0°C
• Stabilizer
38 - 42°C
Replenishment solution tank capacity
• Color Developer
6.6 liters
• Bleach Fixer
6.0 liters
• Stabilizer
17.1 liters
Effluent tank capacity
• Color Developer
4.0 liters
• Bleach Fixer
4.1 liters
• Stabilizer
5.8 liters
Collection of effluents
Two effluents are separately collected by natural dripping.
Dryer
Hot air ink drying method
Energy-saving type using automatic power control
Order classification
• Max. three orders (Varies depending on the paper size.)*1
*1. Maximum 12 orders when print sorter unit type 1 (option) is installed.
Maximum 10 orders when print sorter unit type 2 (option) is installed.
External interface
Ethernet (100Base-TX)
1 port
Display module interface
1 port
External AC power outlet
Outlet type 3 output
Power supply voltage
200 V to 240 V (conform to the power supply specification)
Power capacity
3A
2
Flatbed scanner (recommended products)
Manufacturer
EPSON
Product name
• A4 flatbed scanner
• Perfection 4990 Photo
• Perfection V700 Photo
• Perfection V750
• Actual tank capacities may differ slightly from the volumes shown above.
• Depending on the combination of paper and processing solution, maximum density of print may be different.
For details, contact your place of purchase.
3
Processing capacity
Repeat processing capacity
Print size (Paper width × Paper advance length)
Capacity (Prints/hour)*1
120 mm × 82.5 mm
823
127 mm × 89 mm
781
152 mm × 102 mm
758
203 mm × 102 mm
758
89 mm × 127 mm
622
102 mm × 152 mm
527
127 mm × 178 mm
455
102 mm × 203 mm
402
203 mm × 254 mm
325
203 mm × 305 mm
259
203 mm × 610 mm
96
*1. Calculated according to our criteria. The actual processing capacities may differ depending on various conditions.
Repeat processing capacity
The following is the processing capacity for some types of paper.
Print size (Paper width × Paper advance length)
Capacity (Prints/hour)*1
120 mm × 82.5 mm
688
127 mm × 89 mm
647
152 mm × 102 mm
578
203 mm × 102 mm
578
89 mm × 127 mm
480
102 mm × 152 mm
410
127 mm × 178 mm
356
102 mm × 203 mm
316
203 mm × 254 mm
258
203 mm × 305 mm
217
203 mm × 610 mm
85
*1. Calculated according to our criteria. The actual processing capacities may differ depending on various conditions.
4
Required space and dimensions
Space required for installation
! For single magazine type
2100 or more
250 or more
1390 or more*2
90 or more ∗3
350 or more*1
Extension table (option)
(Unit: mm)
G088213
*1. Extension table (option) not attached
*2. The required space is the same even if the print sorter unit (option) is installed.
*3. If there is additional space in the installation area, we recommend leaving a space of 205 mm or more between the back of system
and wall to facilitate maintenance operations.
! For dual magazine type/triple magazine type
2390 or more
182 or more
90 or more*2
1390 or more*1
250 or more
Dual magazine unit (option) or triple magazine unit (option)
(Unit: mm)
G088214
*1. The required space is the same even if the print sorter unit (option) is installed.
*2. If there is additional space in the installation area, we recommend leaving a space of 205 mm or more between the back of system
and wall to facilitate maintenance operations.
5
Dimensions
1335
1390∗2
640
775 (827*1)
526
1155*3
955
700
Dual magazine unit (option) or triple magazine unit (option)
1499.8
1849.8
(Unit: mm)
1957.8
G088215
*1. When the print sorter unit (option) is installed
*2. When the processing rack is lifted
*3. When the table is raised to the top
6
Power capacity
The values shown here are for installing the power supply.
Supply voltage should be within ±10% of the specified voltage.
The power capacity varies depending on the power supply specification.
See the appropriate information for each specification.
The three-phase four-wire system is not used in the United States.
IMPORTANT
• Use a grounding resistance of 100 Ω or less when grounding this product.
• For details about 1P2W, see ☞ 1P2W.
• For details about 3P3W, see ☞ 3P3W.
• For details about 3P4W, see ☞ 3P4W.
" 1P2W
Supply voltage*1
Power capacity*2
AC 200 V
3.6 kVA (18 A)
AC 208 V
3.8 kVA (18 A)
AC 220 V
3.7 kVA (17 A)
AC 230 V
3.8 kVA (17 A)
AC 240 V
4.0 kVA (17 A)
Wiring chart
Distribution box
Power supply
*3
Circuit breaker
Main circuit breaker
(30 A)
1P2W
(AC 200 V-240 V)
*3
Ground
Printer processor
G075757
*1. Supply voltage should be within ±10% of the specified voltage.
*2. This is the capacity required for power supply installation.
*3. When installing the film processor, be sure to provide a separate circuit breaker from the printer processor.
NOTE
• Leakage current value: 11.2 mA (reference value)
" 3P3W
Supply voltage*1
Power capacity*2
AC 200 V
3.6 kVA (12 A)
AC 208 V
3.8 kVA (13 A)
AC 220 V
3.7 kVA (11 A)
AC 230 V
3.8 kVA (11 A)
AC 240 V
4.0 kVA (11 A)
7
Wiring chart
Distribution box
Power supply
*3
3P3W
Circuit breaker
Main circuit breaker
(AC 200 V-240 V)
(20 A)
*3
Ground
Printer processor
G075758
*1. Supply voltage should be within ±10% of the specified voltage.
*2. This is the capacity required for power supply installation.
*3. When installing the film processor, be sure to provide a separate circuit breaker from the printer processor.
NOTE
• Leakage current value: 11.2 mA (reference value)
" 3P4W
Supply voltage*1
Power capacity*2
AC 346 V
3.6 kVA (9 A)
AC 380 V
3.7 kVA (8 A)
AC 400 V
3.8 kVA (8 A)
AC 415 V
4.0 kVA (9 A)
Wiring chart
Distribution box
Power supply
*3
Circuit breaker
Main circuit breaker
(20 A)
3P4W
(AC 346 V-415 V)
*3
Ground
Printer processor
G075759
*1. Supply voltage should be within ±10% of the specified voltage.
*2. This is the capacity required for power supply installation.
*3. When installing the film processor, be sure to provide a separate circuit breaker from the printer processor.
NOTE
• Leakage current value: 11.2 mA (reference value)
8
Standard equipment
Printer section
Item
Status
Castors
Attached
Magazine*1
1
Table height adjust function
Built-in
Correction value printing unit (CVP)
Installed
Display module
Installed
*1. The paper width can be selected from the following:
89, 102, 114, 117, 120, 127, 130, 152, 165, 178, and 203 (mm)
Paper processor section
Item
Status
Remote effluent tank
Built-in
Effluent level alarm (1 per tank)
Built-in
Dryer overheat prevention system
Built-in
Solution overheat prevention system
Built-in
Processing tank level alarm
Built-in
Circulation pump stop alarm
Built-in
Dryer temperature setting function (for each paper magazine)
Built-in
Drive and dryer automatic stop function
Built-in
Castors
Attached
Print conveyor unit
Installed
Control strip holder
1
Surge absorber (surge protection circuit)
Built-in
Automatic cleaning
Built-in
Replenishment solution remaining amount alarm (1 per tank)
Built-in
Automatic water refilling unit
Built-in
Incorrect cartridge loading prevention function
Built-in
Automatic solution mixing
Built-in
9
Standard accessory
Printer processor section
Name
Quantity
Remarks
C-ring #4
5
Accessory for processing rack
C-ring #6
5
Accessory for processing rack
Vinyl hose (inside diam. 9 mm × outside diam. 13 mm × length
1500 mm)
1
For treating effluent
Slow-blow fuse (3.15 A)
2
Spare item
Slow-blow fuse (6.3 A)
2
Spare item
Slow-blow fuse (10 A)
2
Spare item
Slow-blow fuse (5 A)
2
Spare item
Glass tube fuse (2 A)
2
Spare item
Check date entry sticker
1
Sticker to write the date that float switch
operation was checked
Stick
1
For checking the operation of the float
switch in the processing tank
Cleaning sheet
1
Cloth for cleaning the colorimeter unit
Cleaning wiper
1
Cleaning supply
Lower turn belt
1
Accessory for processing rack
Lower turn belt (3)
1
Accessory for processing rack
Washing bottle (500 ml)
1
For cleaning processing rack
Measuring hose (1)
1
For Color Developer replenishment
solution, Bleach Fixer and Stabilizer
replenishment solution
Measuring hose (2)
1
For measuring replenishment solution
(PS1 and PS2)
Measuring hose (3)
1
For measuring replenishment solution
(PS3 and PS4)
Paper holder
1
For measuring test prints for iBeam
tuning
Plug code (1 m)
1
Power supply cable for PC
Plug code (2.5 m)
1
Power supply cable for monitor
LAN cable (0.7 m)
1
Cross type
Flat cable clamp
5
Anti-contamination cover (includes the maintenance cover)
one each
Chain Oil
1
10
Prevents auxiliary solutions from
dripping into the CD solution when
removing processing racks, etc. (The
maintenance cover is for preventing
processing solution from adhering to the
processor loading unit.)
Oil for lubricating the dryer drive chain
Options (Printer)
Some of the following options may not be available in some countries and areas.
For details, contact your place of purchase.
Printer section
Option No.
Name
Explanation
Z804937-01
DP bag hanger (DH-6)
Hanger for holding developed films and DP bags.
H086044-00
Ink ribbon cassette
CVP ink ribbon
Z811139-01
Dual magazine unit
Unit compatible with the dual magazine type
The paper magazine is required separately.
(available as factory option)
Z811140-01
Triple magazine unit
Unit compatible with the triple magazine type
The paper magazine is required separately.
(available as factory option)
Z811135-01
Expansion table
Mainly used to place the A4 flatbed scanner on.
Z810651-01
Counter unit
Indicates the number of prints.
Z811137-01
Monitor table
Table to place the display monitor on
Z811114-01
LCD monitor arm
Monitor arm with which you can freely change direction
of the display.
Z811147-01
Rear cover
The cover to hide the rear side of the machine.
Z811191-01
Storage cabinet
When the table is raised, a cabinet can be installed under
the table.
I068490-00
Plug cord
For connecting the scanner (1.5 m)
Paper magazine
Option No.
Name
Z811196-02
Paper magazine, 89 mm
Z811196-03
Paper magazine, 102 mm
Z811196-04
Paper magazine, 114 mm
Z811196-05
Paper magazine, 117 mm
Z811196-06
Paper magazine, 120 mm
Z811196-08
Paper magazine, 127 mm
Z811196-09
Paper magazine, 130 mm
Z811196-10
Paper magazine, 152 mm
Z811196-11
Paper magazine, 165 mm
Z811196-12
Paper magazine, 178 mm
Z811196-13
Paper magazine, 203 mm
Explanation
Include Magazine spindle unit 1 and handle.
11
Options (Paper processor)
Some of the following options may not be available in some countries and areas.
For details, contact your place of purchase.
Paper processor section
Option No.
Name
Explanation
C008075-01
Floor tray
Placed underneath the system to prevent the floor from
becoming dirty.
B011625-01
Rack transportation tank
Used to transport wet processing racks.
C101570-01
Turn rack vat
Container for immersing the upper guide in water.
A202513-01
Filler
5-liter measuring pitcher
H049014-00
Effluent tank
Collects effluent that overflows from the processing
tanks. (20 liters)
L005253-00
Measuring cylinder
Used to measure replenishment solution, etc. (200 ml).
Z810657-01
Minute meter unit
Displays the system operating time.
Z811175-01
Sorter modification kit (10 orders)
Modifies the print sorter unit to support 10 orders (only
when print sorter unit type 1 is installed)
H089016-00
Cleaning sheet
Used to clean the pressure roller of the colorimeter unit.It
should be cleaned every six months. Three sheets
included.
Z811171-01
Print sorter unit (type 1)
Allows prints to be sorted by order (12-order type).
Z811172-01
Print sorter unit (type 2)
Allows prints to be sorted by order (10-order type).
Z811150-01
Control strip auto loading unit
Unit to process the control strip without using the control
strip leader.
12
Commercially available items to be
prepared by the customer
The items below are required according to the installation environment of the customers.
They should be prepared by customers if necessary.
Item
HUB
LAN cable
Remarks
When several systems are connected to the PC, a hub is
necessary. (Should be with the required number of 100BASE-TX
ports.)
Cross type
The cable of 0.7 m is supplied as a standard accessory. If the
longer cable is required, prepare the longer cable.
Straight type
Prepare this when connecting the system using a HUB.
13
Installation requirements
• This system is to be used in a location with a relative humidity from 30 to 75% and temperature from 15 to 30°C (59 to
86°F).
• The light source for this system should be a natural light color, and the light intensity should be between 300 and 400 lux.
If there are lights near to the system, they must be screened. In particular, if the product is installed near a window, use
curtains or blinds to block direct sunlight from the product.
• Do not install the product in a place where the operator is exposed to direct sunlight. Make sure the display monitor is
located away from direct sunlight or other bright light sources.
• Avoid installing the product in areas with high dust levels or subject to vibration.
• Do not raise or lower the room temperature quickly. Raising the temperature quickly can cause condensation inside the
system, which leads to problems such as lens fogging, paper jam, and malfunctions in the electronics and PCBs.
• Because the system uses liquids during normal operation, please make sure that the floor and walls are waterproof for
safety reasons. In addition, we recommend installing a sink or drain in the room to facilitate washing racks.
• Castors are for moving the system. Once the system has been installed, be sure to fix it in place with the adjusters or jack
bolts.
• If the level difference of the floor on which the system is installed (the height difference between jack bolts) is 10 mm or
more, a plate or shim should be used to adjust the level.
• Use this system in a DC magnetic field (earth magnetic field, etc.) of 0.6G*1 or less and AC magnetic field (power source
magnetic field, etc.) of 0.06G*1 (rms) or less.
*1. 0.6G = 60µT, 0.06G = 6µT
• The system is programmed with default values prior to shipment. These values may differ depending on the environment
and operating conditions. Change them as necessary.
• The maximum permissible system impedance Zmax of this system is 0.063+j0.039Ω, supplied from a power distribution
system having a rated voltage of 400/230 V. This system is connected only to a supply of that impedance or less.
Determine the connection to a power supply in consultation with the supply power company.
• This equipment complies with EN61000-3-12.
Subject to change without notice.
14