Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
fTEtITIEI74Ä? -_ F I' E .I---r--t-- -- - F I - ,l TE IJ ä T tll EC.TYPE EXAMINATION CERTIF'ICATE 12] Equipment or Protsctive Systems intended for use in Potentially Explosive Atmospheres Directive 9419tEC l3l t4l Certificate Number: SP12ATEX3164X Equipment or Protective System: Fans of types KTEX 50-25-4, KTEX 50-30-4, KTEX 60-30-4, KTEX 60-35-4 and KTEX 70-40-6 t5l t6l L7l Applicant (manufacturer): Systemair AB l8l SP, Notified Body No. A402 in accordance with Article 9 of the Council Directive 9a/9/EC of 23 March 1994, certifies that this equipment or proteotive system has been found to comply with the Essential Health and Safety Requirements relating to the design and construction of equiprnent and protective systems intended for use in potentially explosive atmcspheres, given in Annex II to the Directive. The examination and test results are recorded in a confidential repof No. PX08403:A t9] Address: Industrivägen 3, SE-739 30 Skinnskatteberg, Sweden This equipment or protective syst€m and any acceptable variation thereto is specified in the schedule to this certificate and the documents therein referred to. Compliance with the Essential Health and Safety Requirements has been assured by compliance *'ith: - EN 60079-0:2009 (SS-EN 60079-0 ed.Z) - EN 14986:2007 (SS-EN 14986 ed. 1) - EN 60079-7:2AA7 (SS-EN 600"19-7 ed. 2) This certificate is also based on certificates and standards, for certified parts included in the equipment, according to item 18 in the schedule of this c.ertificate. l10l If the sign "X" is placed after the certificate nurnber, it indicates that the equipment or protective system is subject to special conditions for safe use specified in the schedule to this certificate. ll 1l This EC Type examination certificate relates only to the design, examination and tests of the specified equipment or protective system in accordance to the Directive 94l9lEC. Further requirements of the Directive apply to the manufacturing process and supply of this equipment or protective system. This certificate does not cover these requirements. 1121 The marking of the equipment or protective system shall include the following: '€s.l Ii 2G Ex e rrB+g" 3th T3 Gb December 2012 nical Research Institute of Sweden SP SP Manager Notified Certificate ref.: 12 68 32 No. 0402 SP Technical Research lnstitute of Sweden Posfal SP Box addross 857 SE-50'1 15 Borås SWEDEN Pfene / Fax Rw.nu.nM E.nail / lnlernet +46105165000 556464-6874 [email protected] +46 33 13 55 02 Vt/lW.Sp.Se Swedish Notifred Bodies are appointed by SWEDAC, the Swedish Board for Åocreditation and Conformity Assessment, under the tenn$ of Swedish leglslation. This certificate may not be roproduced 0ther than in tull, except wih tile priorwittefl apploval by SP. fTED?IEItrNT -xr E F II-TII -lll-- h F - - - F E !n ---rt I II r I - l3l Schedule []41 EC-TYPE EXAMINATION CERTIFICATE No. SP 12ATEX3164X t tl5l Description of equipment The fans of type KTEX consist of housing a fan wheel and a certified induction motor with a permanently connected cable. The material in the riveted construction is galvanic sheet metal except for the inlet cone whieh is made of copper. Fans of types KTEX 50-25-4 and KTEX 50-30-4 either have a rnotor for supply voltage 230 V or a motor for supply voltage 400 V. Fans of types KTEX 60-30-4, KTEX 60-35-4 and KTEX 1A-4A-6 have motors that can be either Yconnected for supply voltage 400 V or D-connected for supply voltage 230 V by the user. The motors have degree of protection IP44. The fans ean be speed controlled by applying reduced supply voltages according to the table below. The fan motor is equipped with three PTC temperature sensors; these sensors are intended for connection to separate supervision equipment. Bata Type ofduty: Ambient temperature Supply voltage: S1 (continues dufy) -24 oC to *40 0C (T*): 400 V ac 230 V ac 3-, 50 Hz 3-, 50 FIz Trble I, Rated data for fans Fan gpe Current Power Speed tn (rnotor fype in (A) (kw) (rpm) (s)t) Ia1Ir,. Operated with reduced voltage Current (A) By transformer (V) By three phase parenthesis) a.c controller (V) KTEX 50-25-4 {MKl06-4DK.07.Y) KTEX 50-30-4 (MK106-4DK.l4.Y) KTEX 60.304 (MK137-4DK. r0.Y) KTEX 60-35-4 t.47t0.85 0"49 n9a 8l 3,4 35-230190-400 60-230/100-400 r,64/4,95 3,1i r,8 0,9 l3 55 50 4,1 35-230/90-400 60-23011 00-400 3,28/1,91 3,812,2 1,3 1330 85 4,1 35-230i90-400 60-230/100-400 4,14/2,40 6,8t3,9 2,1 1380 60 s't 35-230/90-400 60-230/100-400 7,9514,56 6,413,7 1,8 840 160 i) 35-230/90-400 50-230/100-400 6,413,7 {MK137-4DK.20.Y) KTEX 70-40-6 {MK137-6DK.20.Y) oC) Based on rated voltage and cold state (+20 The rated data denoted 'r'+*/**'t in the table applies for 230 Vl400V supply Schedule to Certificatg No. S?:|.2ATEX3164X SP Technical Research lnstitute of Sweden Fhane l Fax Reg.nunöet E nail/ fustaleddress SP Box 857 SE-501 15 Borås SWEDEN +46 105 16 50 +46 33 13 55 00 5564&{4874 02 lnternet inlo@so,s-e www.sp.se *. P?se 2(4) - Swedish Notified Bodbs are appoårted by SWEDAC, Sre $rvedish Board for Accreditation and Coniormity Assessment" under the terms of Swedish legislation. This certr'ficate may not be reproducod olher lhan in iull, except with the prbr writen approval by SP. FED?TETWfr? l-FFtlFn.Ir : tr6l Report E rr - = = = =E* = No. PX08403:A l17l Special conditions for safe use ttsl 1 The fans shall be installed and used so as not to exceed the rated current and power on the marking plate of the fan. However, when fans are run at partial voltage by a transformer or a three phase a.c controller, the current may exceed the curent on the marking plate according to the table 1 in the certificate as long as the rated power is not exceeded. A minimum backpressure may be required to maintain the rating of the fan. 2 The PTC thermal protection circuits of the rnotors shall be connected to a higgering device certified according to Directive 9419/EC, which shall immediately disconnect the motor from main supply upon activation of the PTC-sensors. 3 When the fans are installed in a duct system the degree of protection IP 20 at the inlet side and IP at the outlet side shall be fulfilled for the duct system. Parts that conffibute to this protection shall have a suitable design with respect to strength and material. 4 The cable shall be fixed by the installation with adequate clamping, mechanically protected and suitable for the environment, to ensure the explosion protection. The connection of the free end of the cable shall be explosion protected according to the valid installation regulations. 5 External sources of heating or cooling shall be considered so that the ambient temperatue and the temperature of the conveyed air are kept in the range -20 to +40'C. l0 Essential health and safety requirements None additional to those covered by the standards listed in item 9' The equipment includes pre certified parls which has not been subject to type examination by SP. This certificate is based on type examinations performed earlier for such parts according to EC-Type Examination Certificates specified in the table below and based on the presumption that the essential health and safety requirements (including current technological knowledge of explosion protection) according to the Directive 94/9lEC, are fulfitled by the manufacturer as required for products placed on the market. schedule to certificate No. sP12ATEX3'164X SP Technical Research lnstitute of Sweden Postal addrcss SP Box 857 SE-501 15 Borås SWEDEN Pf:r,ne I Fax Reg.wnber 00 5564M-6874 02 +46 105 16 50 +46 33 13 55 Eaaill lntenet [email protected]€ w\tw.sp.se Swedish Notified Bodies are appointed by SWEDAC, the Swedish Board for Accreditation and Conformity Assessment, underthe terms of Swedbh legislation. This certilicate may not be reproduced oher tran in full, except with the prior written approval by SP. 'rED?ltlvnT E I- l-FFII-Eh----II '--t--Itt IJ -r-- I - 2. Precertified Table t Certificate No. Equipmento code Used in fan Standards type 1 Motor type MK I 06-4DK.07.Y manufacfired by Ziehl Abegg AG PTBO8ATEX306l (incl. datasheet no. 14) KTEX 50-25-4 EN 60079-0:2006 EN 60079-7:2007 PTBOSATEX306I (incl. datasheet no. 3) KTEX 50-30-4 EN 60079-0:2006 EN 600?9-7:2007 PTBO8ATEX3062 KTEX 60-30-4 EN 60079-0:2006 EN 60079-7:2007 PTB08ATEX3062 (incl. datasheet no. 2) KTEX 60-35-4 EN 60079-0:2006 EN 60079-7:2007 PTBO8ATEX3062 KTEX 70-40-6 EN 60079-0:2006 @Itzc ExeIIT3 ) Motor type MKI 06-4DK.14.Y manufactured by Ziehl Abegg AG. @ttzc ExeIIT3 3 Motor type MK137-4DK. I 0.Y manufactwed by Ziehl Abegg AG (incl. datasheet no. 1) @Itzc ExeIIT3 4 Motor type MKI 3 7-4DK.20.Y manufactured by Ziehl Abegg AG Ottzc 5 ExeIIT3 Motor qrye MKl 37-6DK.20.Y rnanufactured by ZiehlAbegg AG @ttzc EN 60079-7:2007 Exe IIT3 Note: The specificarion of equipment tlgl (incl. datasheet no. 4) and standards are limiled to those relevant for the equipment covered by this certificEte. Drawings and documents According to Test Repon PX08403:A Schedule to Certificate No. SP12ATEX3164X SP Technical Research lns$tute ofSweden Postal SP Box address 857 SE-501 15 Borås SWEDEN Fax Reg.tunfut +4O 105 16 50 00 556464-6874 Plarc / +46 33 13 55 02 E{natl / lfiternel [email protected] wu/lr/.sp.se Swedish Notified Bo'dkx are appokrted by SWEDAC, the $wedish Boad for Accrcditation and Confoimity Assessment under the terms of Swedish legi$lation. This certi{icate may not be reproduced oher than in full, except with lhe prior written approval by SP. Supplement No. 1 to EC-TYPE EXAMINATION CERTIFICATE Equipment or Protective Systems lntended for use in Potential ly Explosive Atmospheres Directive 94l9lEC Certificate Nunnber: SP12ATEX3164X The certificate SP1zATEX3164X of 3.12.2At2, and the rights and duties associated with the certificate, is taken over by the following company as of 01-.05.2015: Applicant(manufacturer): Address: SystemairSverigeAB lndustrivägen 3, SE-739 30 Skinnskatteberg, Sweden The change is due to a restructuring of the company Systemair AB (manufacturer and holder of the certificate), The new manufacturer and holder of the certificate (Systemair Sverige AB) has the same address as Systemair AB, but ä name and organization registration no. which differs from the name and organization registration no. of Systemair AB. The specifications according to the certificate (SP12ATEX316aX) apply except that the name of the manufacturer is changed from "Systemair AB" to "Systemair Sverige AB" in the marking and in the accompanying instructions for the products. Report No. File No.: 5P03723 Drawings and documents The change specified above of the manufacturer's name, applies for the marking and accompanying instructions according to the following documents: Desription Typskylt 400 V 3-fas Typskylt 230 V 3-fas Typskylt 400 V 3-fas Typskylt 230 v Typskylt 230/400 V Typskylt 230/400 V Typskylt 230/400 v Etikett, Tillv,order.nr Rev Number Pages 1 page 121.023 1Ll2-5 121.023 1112-51 11L3-5 1"21023 L1L4-s 111s-s 121,:A23 1 page 1 page 1 page 121023 120208 121108 1 page 1 page 8 pages 121023 L21A23 L3500-21- Drift- och underhållsinstruktion ver. A001 Notel Date 1111-5 LL11-51 1 page 1 page One set of the drawings and documents above, submitted to the holder of this certificate, contain cotnments by SP which shall be considered by the holder {according to this supplement, "Systemair AB" shall be changed to "Systemair Sverige AB" in the documents). Supplement No. 1, issued 2015-05-01, to Certificate No. $P Technicel Research lnstitute of Sweden 8ox 857, SE-501 LS Borås,Sweden Phone: +46 10-516 50 00 F-mail: [email protected] www.sp.se 5P12ATEX3164X SP Certificate ref:126832 Page L (2) The Council Dhective 94/9lEC is implemented in Swedish Låw by the national regulation ELSÄK-FS 1995:6 and AFS 1995:5.Swedish Notified Bodies are appointed by SWEDAC, the Swedish Board for Accreditåtion and Conformity Assessment, under the terms of Swedish legislation. This certificate may not be reproduced other than in full, except with the prior written approval by SP. SPs Certification Rules SPCR 079 has been applied. L't May 2015 SP Tech ch lnstitute of Sweden Body No.0402 nart Aronsson C€rtification Manager W Certification Officer Supplernent No.1, issued on 2015-05-01, to Certificate No. SP12ATEX3164X SP Technical Research lnstitute of Sweden gox 857, SE-501 15 Borås,Sweden Phone: +46 10-516 50 00 E-mail: [email protected] www.sp.se SP Certificate ref: 126832 Page 2 (2) The Council Directive 94/9/EC is implemented in Swedish Law by tha national regulation E6ÄK-FS 1995:6 and AFS 1995:5.swedish Notified Bodies are appointed by SWEDAC, the Swedish Board for Accreditation and Conformity Assessment, under the terms of Swedish legislation. This certificate may not be reproduced other than in full, except with the prior written approval by SP. SPs Certification Rules SPCR 079 has been applied.