Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Simplese D Installation Guide CD1 CD2 CD1 CD2 CD1 CD2 CD1 CD2 TNR1 TNR2 TNR1 TNR2 TNR1 TNR2 TNR1 TNR2 C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C MODEL NV-P2100 HIGH EFFICIENCY 200 WATT STEREO AMPLIFIER 120V 60HZ 250 WATTS NuVo Technologies Cincinnati Ohio. USA AUDIO SPEAKER CONTROL CONTROL USE ONLY WITH 250V FUSE L SENSITIVITY OdBV = 1.0RMS INPUT 2 POWER MODE ON/OFF SWITCH AUDIO AC/DC RIGHT 0 LEFT 0 VOLTAGE UNIT TRIGGER ON 3-30 VOLTS AC OR DC OUTPUT POWER 8 OHM: 70W X 2 4 OHM: 100W X 2 +12VDC 100mA R +6 INPUT 2 1 3 L 4 ZONE 4 38KHz 56KHz 3 1 L L -12 +6 -12 OUTPUT D STATUS ON= +12V 1 LINK FOUR-SOURCE FOUR-ZONE Simplese SPEAKER AND DATA SIGNALS R R 50~60Hz 85W 2 4 MUTE =0V 2 ERTEK CONFORMS TO UL STD.6500 CERTIFIED TO US CAN/CSA STD.E60065 C 3033118 RS232 NT ER TEK I R IN T CM 100~240V NuVo Technologies Cincinnati Ohio USA FIXED SOURCE INPUT Source 1 Tuner 1 Audio Out Source 2 Tuner 2 VAR LINE OUT NORMAL USE USE FOR SAT OR CABLE Source 3 CD Audio Out SYSTEM IR OUT ALL PORT CONNECTION Audio Out Source 4 DVD Audio Out Simplese D Wiring Diagram Step 1 Prewire: The Simplese D System uses Cat-5 wire for keypad control and either 2 or 4 conductor 16 gauge speaker wire. The termination for the Cat-5 wire is standard 568A. Simplese uses an RJ-45 connector on each end of the Cat-5. Note that both the speaker wire and Cat-5 are run to the Allport location at the equipment rack or cabinet. Step 2 Allport™ Termination: Both the speaker wire and Cat-5 cables terminate into the backside of the Allport. The order of Cat-5 plug-ins is irrelevant to the operation of the system, but it is recommended that you label the Cat-5 wires for future reference. Follow the zone and polarity labeling for the speaker wires. The final connection from the Allport is made with the Allport Cable supplied with the Simplese D System. Step 3 Connecting Audio Sources: The Simplese D system will accept up to four independent audio sources. This is done with stereo RCA audio cables from the audio output on each source to the appropriate source input on the back of the Simplese amplifier. Step 4 IR Outputs: The Simplese D System ships with four IR emitters for transferring IR data from the keypad receivers (located under the volume button) to the IR receiver on each piece of source equipment. There are two separate IR output sections. The 38K outputs are used most all audio sources. The exception to this frequency are cable and satellite boxes. They operate at a higher IR carrier frequency around 56K. A second source one and two 56K output is available for these devices, see fig. 1. It is important that the output being used for each source matches the source input number. The outputs are individual for each source to allow independent source control. Simply plug the emitter into the appropriate IR output on the back of the Simplese amplifier and attach the flasher end over the IR receiver on the source equipment. Fig. 1: 38KHz and 56KHz IR Outputs 38KHz 56KHz 1 3 2 4 NORMAL USE 1 2 USE FOR SAT OR CABLE IR OUT Step 5 Keypad Setup: Each keypad requires a specific zone setting to establish the keypad’s location. This setting is made on the back of the keypad using an eight position rotary switch. To set the switch, place a small slot-head screwdriver in the slot in the switch and turn it clockwise to the appropriate zone number 1-4, fig. 2. The remaining switch positions, 5-0 allow for an additional keypad in each zone. Position 5 corresponds to zone 1, 6 to zone 2, 7 to zone 3, and 0 to zone 4. Fig. 2: Zone setting rotary switch 0 1 2 3 5 6 7 4 Step 6 EQ Control, and Source Grouping: The keypads can be used to set specific zone functions. These are bass and treble EQ response, and source grouping. To change bass response, press the Mute button and Source 1 button simultaneously. Adjust the bass level up or down by using the volume up and volume down buttons. The volume indicator LEDs will indicate the output level, fig. 3. The default setting is flat. Adjusting treble is the same process and is accessed by pressing the Mute and Source 2 buttons. Once the desired setting is made, press the Source button again and that returns the keypad to normal operation. Source grouping is a featured that allows multiple zones in an open living space to always share the same source selection, but still retain individual volume and on/off control. This is achieved by pressing Mute and Source 3. Volume Up enables the group function and Volume Down disables the group function and causes the keypad to operate independently of all other groups, fig. 4. Fig. 3: Zone EQ Control -4 dB FLAT +4 dB -6 dB +6 dB -8 dB +8 dB VOLUME Fig. 4: Zone Group Settings Group Disabled Group Enabled VOLUME Step 7 Final Setup: Once the sources are plugged in and the keypads are set and installed you should be ready to power on any of the zones and enjoy music from any of the sources. Simplese D Specifications Zones 1-6 Power Amplifier Outputs Continuous Average Output Power 30W (15W x 2) Two channels driven 30-20kHz @1% THD Rated Distortion (1/2 power) 0.40% Rated Impedance 6 Ohms Damping Factor 50+ 50/60Hz Frequency Response (20-20kHz) "+2dB Preamplifier Section Variable output Fixed output Impedance Source Inputs 1-4 input Impedance Input Sensitivity for rated power Input Overload 0-600mV 600mV 600 Ohms 10K 300mV RMS 3V RMS Emitter Outputs Source Outputs 4 Output Drive Current 100mA Output Drive Voltage 12V Compatible with single and dual emitters System System On External Mute 12V @ 50mA 3-12V DC Power Requirements Power Supply 90-260VAC Power Consumption all channels 140W driven to full-rated power Cower Consumption average 30W operating conditions Power Consumption no signal 10W Physical Specifications Unit Size Millimeters Unit Size Inches Unit Weight Kilograms Unit Weight Pounds 44 x 430 x 270 1.75 x 17 x 10.625 2.95 6.5 NuVo reserves the right to change specifications without notice.