Download biopotential amplifiers

yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Document related concepts

Heterodyne wikipedia, lookup

Pulse-width modulation wikipedia, lookup

Transistor wikipedia, lookup

Loudspeaker wikipedia, lookup

Alternating current wikipedia, lookup

Rectifier wikipedia, lookup

Stray voltage wikipedia, lookup

Current source wikipedia, lookup

Bode plot wikipedia, lookup

Voltage optimisation wikipedia, lookup

Flip-flop (electronics) wikipedia, lookup

Signal-flow graph wikipedia, lookup

Dynamic range compression wikipedia, lookup

Buck converter wikipedia, lookup

Mains electricity wikipedia, lookup

Sound reinforcement system wikipedia, lookup

Scattering parameters wikipedia, lookup

Oscilloscope history wikipedia, lookup

Oscilloscope types wikipedia, lookup

Switched-mode power supply wikipedia, lookup

Resistive opto-isolator wikipedia, lookup

Audio power wikipedia, lookup

Two-port network wikipedia, lookup

Metadyne wikipedia, lookup

Regenerative circuit wikipedia, lookup

Schmitt trigger wikipedia, lookup

Negative feedback wikipedia, lookup

Rectiverter wikipedia, lookup

Instrument amplifier wikipedia, lookup

Public address system wikipedia, lookup

Wien bridge oscillator wikipedia, lookup

Tube sound wikipedia, lookup

Opto-isolator wikipedia, lookup

Amplifier wikipedia, lookup

Engr. Hinesh Kumar
 Amplifiers used to process biopotentials are called
biopotential amplifier.
Biopotential Signals (e.g., ECG, EMG, EEG, EOG, … etc.)
The basic function of biopotential amplifier is to increase
the amplitude of a weak electric signal of biological
Biopotential amplifiers typically process voltages, but in
some cases they also process currents.
The frequency response of typical bioelectric amplifiers
may be from dc (or near dc, i.e., 0.05 Hz) up to 100 kHz.
 Some biopotential amplifiers are ac-coupled, while
some are dc-coupled.
The dc-coupling is required where input signals are
clearly dc or changes very slowly.
At frequencies as low as 0.05Hz, the ac-coupling
should be used instead of dc-coupling.
This is to overcome the electrode offset potential.
Also, the skin-electrode interface generates dc offsets.
The gain of biopotential amplifiers can be low, medium
or high (x10, x100, x1000, x10000).
 Gain factors x1 and x10.
 The unity-gain amplifier is mainly for isolation,
buffering and possibly impedance transformation
between signal source and readout device.
 Used for measurement of action potentials and
other relatively high-amplitude bioelectric events.
 Gain factors x100 and x1000.
 Used for recording of ECG waveforms and
muscles potentials (EMG), etc.
 Gain factors over x1000.
 Used in very sensitive measurement such as
recording of brain potentials (EEG).
The basic requirements that a biopotential amplifier has
to satisfy are:
1. Biopotential amplifiers should have high input
impedance i.e., greater than 10 MΩ.
2. Safety: the amplifier should protect the organism
being studied.
 Careful design to prevent macro and micro shocks.
 Isolation and protection circuitry to limit the current
through the electrode to safe level.
3. Output impedance of the amplifier should be low
to drive any external load with minimal distortion
4. Gain of the amplifier is greater than x1000 as
biopotentials are typically less than a millivolt.
Most biopotential amplifiers are differential
amplifier as signals are recorded using a bipolar
electrodes which are symmetrically located.
High Common Mode Rejection Ratio (CMMR):
biopotentials ride on a large offset signals or noise.
Rapid calibration of the amplifier in laboratory
Adjustable Gains:
 Often the change in scale is automatic
 Therefore calibration of the equipment is very important
10. The physiological process to be monitored should
not be influenced in any way by the amplifier.
11. The measured signal should not be distorted.
12. The amplifier should provide the best possible
separation of signal and interferences.
13. The amplifier has to offer protection of the
patient from any hazard of electrical shock.
14. The amplifier itself has to be protected against
damages that might result from high input
voltages as they occur during the application of
defibrillators or electrosurgical instrumentation
Circuit Model of Operational Amplifier
Dual Power Supply Configuration for Operational
Dual Power Supply Connections for Operational
Typical Signal Voltage Sources for Operational
 There are many circuit configurations using op
amps as the active device, but only three basic
classes of voltage amplifiers exist:
1. Inverting Amplifier
2. Non-inverting Amplifier
3. Unity Gain Non-inverting Amplifier
 Inverting amplifier consists of an op-amp, an input
resistor (R1), and a feedback resistor (R2).
 The noninverting input is grounded in this circuit.
 The point A, the junction of the two resistors and the
operational amplifier's inverting input, is properly
called the summing junction, or summation node.
 The quantity R2/R1 gives us the magnitude of the
voltage gain for this amplifier configuration, and the
minus sign tells us that a 180-deeree phase inversion
takes place. The voltage amplification or gain
expression is represented by the symbol Av
 The equation is also frequently seen in two alternative
but equivalent form.
 Calculate the gain of an inverting amplifier if the
feedback resistor (i,e., R2) is 120 kΩ. and the input
resistor (R1) is 5.6 k Ω
 Solution
Av= -R2/R1
Av= -(120 k Ω / 5.6 k Ω)
Av= 21
 In the non-inverting amplifier input voltage is applied
directly to the non inverting input terminal of the
operational amplifier .
 Feedback resistor R2, and input resistor R1, are the same
as in the inverting follower, except that the other end of
R1, is grounded.
 Calculate the voltage gain of a “non-inverting amplifier
if R2, = 10 k Ω and R1, = 2.2 k Ω.
At high gains, the gains of the inverting and non-inverting amplifier are very nearly
equal but, at low gains, a difference is noted.
 In the unity Gain non-inverting amplifier the resistor
network is not used in this circuit, and the output is
connected directly to the inverting input, resulting in
Av= R2/R1+1
Av= 0+1
Av= 1
 More than one input network may be used in an op-
amp network, and the output voltage represents the
summation of the respective input currents.
 Three input networks are used in this circuit, and
there are three input sources: E1, through E3.
 Find the output voltage in a circuit, such as one in fig,
if R1, = R2, = R3, = 10 k Ω , R4 = 22 k Ω, E1, = 100 mV,
E2, = 500 mV, and E3, = 75 mV.
 A differential amplifier produces an output voltage that is
proportional to the difference between the voltage applied
to the two input terminals.
 The voltage gain for the differential signals is the same as
for the inverting followers, provided the ratio equality of
R2/R1 = R4/R3 is maintained.
 Differential amplifiers are useful because it rejects common
voltages while amplifying the differential signal of interest.
 This circuit uses three operational amplifiers, A1, through
The two input amplifiers (i.e., A1, and A2,) are connected in
the non-inverting amplifier configuration, while the third
amplifier is connected in the simple dc differential
Simplify circuit analysis by setting the gain of A3, equal to
unity (i.e.. R4, = R5, = R6, = R7,).
let us assume E1, is applied to the non-inverting input of
amplifier A1, and that E2, is applied to the non-inverting
input of amplifier A2.
Additionally, E3 is the output of A2,, and E4 is the output of
Voltages E1, and E2 are also shown at the inverting inputs of
A1 and A2.
There are two contributing sources to E3, and E4. In the case
of E3:
If we set R2=R3
 The gain of instrumentation Amplifier is