* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download 1 - JustAnswer
Integrating ADC wikipedia , lookup
Spark-gap transmitter wikipedia , lookup
Immunity-aware programming wikipedia , lookup
Distributed element filter wikipedia , lookup
Phase-locked loop wikipedia , lookup
Power MOSFET wikipedia , lookup
Transistor–transistor logic wikipedia , lookup
Integrated circuit wikipedia , lookup
Crystal radio wikipedia , lookup
Surge protector wikipedia , lookup
Standing wave ratio wikipedia , lookup
Negative-feedback amplifier wikipedia , lookup
Oscilloscope history wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Schmitt trigger wikipedia , lookup
Current mirror wikipedia , lookup
Power electronics wikipedia , lookup
Operational amplifier wikipedia , lookup
Valve audio amplifier technical specification wikipedia , lookup
Radio transmitter design wikipedia , lookup
Two-port network wikipedia , lookup
Regenerative circuit wikipedia , lookup
Zobel network wikipedia , lookup
Wien bridge oscillator wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Index of electronics articles wikipedia , lookup
RLC circuit wikipedia , lookup
Opto-isolator wikipedia , lookup
1. The output voltage of a power supply is measured at 12 V with no load connected. The manufacturer’s specifications say the power supply has a regulation of 10 percent. What is the full-load output voltage of the power supply? A. 13.2 V B. 10.9 V C. 10.8 V D. 1.2 V 2. A modulation technique that’s used in fiber-optic transmission in which the width of pulses is varied in accordance with the modulation signal is called A. PRM. C. PWM. B. PPM. D. PAM. 3. Two electronics technicians are discussing LC and RC oscillators. Technician A says that an RC oscillator doesn’t require a resonant circuit. Technician B says that an LC oscillator can be tuned only by varying the inductance, and that an RC oscillator can’t produce a sine wave. Which of the following statements is correct? A. Only Technician A is correct. B. Only Technician B is correct. C. Both of the technicians are correct. D. Neither of the two technicians is correct. 4. Look at the four circuit diagrams that are shown in Figure A-1. Which of these four diagrams represents a correctly configured full-wave bridge rectifier circuit? A. Circuit 1 C. Circuit 3 B. Circuit 2 D. Circuits 4 5. Which of the following is essential for the operation of an oscillator? A. Positive feedback C. A unity gain amplifier B. Degenerative feedback D. An LC circuit 6. Look at the circuit diagram and the four waveforms that are shown in Figure A-2. Assume that diode D1 in the circuit is opened. Which of the four waveforms shown in the figure would appear across RL? A. Waveform 1 C. Waveform 3 B. Waveform 2 D. Waveform 4 7. Look at the amplifier circuit shown in Figure A-3. Which of the following statements about this circuit is correct? A. This is a common-collector circuit that’s characterized by low input impedance and a high output impedance. B. This is a common-collector circuit that’s characterized by a high input impedance and a low output impedance. C. This is a common-emitter circuit that’s characterized by a low input impedance and a high output impedance. D. This is a common-emitter circuit that’s characterized by a high input impedance and a low output impedance. 8. Negative clipping of an output signal occurs when the A. output impedance is too high. C. input amplitude is too high. B. input impedance is too high. D. power supply voltage is too high. 9. Look at the circuit diagram shown in Figure A-4. When R1 and R2 are equally illuminated, the lamp I1 glows dimly. Which of the following will happen if R2 is covered so that no light can reach it? A. Lamp I1 glows brighter, because the forward bias on Q1 is decreased. B. Lamp I1 goes out, because the forward bias on Q1 is decreased. C. Lamp I1 glows brighter, because the voltage on the base of Q1 goes positive. D. Lamp I1 goes out, because the forward bias on Q1 increases. 10. One advantage of using photon coupling for signal transmission is the A. lower power required for transmission. B. greater immunity to noise pickup C. lower cost of signal-handling components D. greater adaptability to digital transmission 11. A full-wave power supply with a capacitor-input filter is connected to a 400 Hz AC source. The frequency of the ripple waveform at the input to the filter is A. 0 Hz (DC). C. 400 Hz. B. 100 Hz. D. 800 Hz. 12. Look at the circuit diagram shown in the figure A-5.what is the power level at point B in the circuit? (A) 0.31mW (B) 3.1mW (c) 62mW (d) 620mW 13. In the circuit diagram shown in the figure A-5.what is the power level at point A (A) 0.31mW (B) 3.1mW (c)31mW (D) 310mW 14. What would happen at the output of a full-wave bridge rectifier circuit if one of the diodes in the bridge opened? A. The ripple frequency would decrease, and the voltage would decrease. B. The ripple frequency would increase, and the voltage would decrease. C. The ripple frequency would remain the same, and the voltage would decrease. D. The ripple frequency would remain the same, and the voltage would increase. 15. Look at the four circuit diagrams shown in Figure A-6. Which of these four diagrams shows a correctly biased Class A amplifier? A. Circuit 1 C. Circuit 3 B. Circuit 2 D. Circuit 4 16. Two electronics technicians are comparing a full-wave bridge rectifier to a full-wave rectifier that uses two diodes and a center-tapped secondary. Technician A says that the twodiode rectifier has a lower ripple frequency and can supply greater current than the full-wave bridge rectifier. Technician B says that the full wave bridge rectifier results in full secondary voltage at the output. Which of the following statements is correct? A. Only Technician A is correct. B. Only Technician B is correct. C. Both of the technicians are correct. D. Neither of the two technicians is correct. 17. Look at the circuit diagram and four waveforms that are shown in the figure. Assume that the circuit’s switch is closed momentarily, then opened. Which of the four waveforms shown will appear between terminals A and B after the switch is opened? A). waveform 1 B) waveform 2 (c) waveform 3 (D) waveform 4 18. A 100 kHz oscillator that’s followed by a doubler and two triplers will produce an output frequency of (A) 180kHz (B) 500 kHz (c) 800kHz (D) 1.8 MHz 19. Look at the circuit diagram shown in the fig A-8. What is the voltage between point A and ground? (A)+6V (B) -6V (c) +25V (D)-25V Answer: Assuming those are Zener diodes. Without the diodes, the potential across the first two resistors would be 12V each. This is greater than the potential of the diode, so the current flows through the diode and the potential across each of the first two resistors is 5V. This means the potential across the third resistor is 20 V. So the potential from point A to the ground is +25V 20. In the circuit shown in fig A-8 what is the current through R2? (A) 25mA (B) 60mA (C) 2.5mA (D) 6.00mA Answer: V = 5 volts, R = 2 k so I = V/R = 5 / 2 = 2.5 milliamps