* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download User Manual F6
Transformer wikipedia , lookup
Power engineering wikipedia , lookup
Variable-frequency drive wikipedia , lookup
Electrical ballast wikipedia , lookup
Power inverter wikipedia , lookup
Three-phase electric power wikipedia , lookup
Current source wikipedia , lookup
Electrical substation wikipedia , lookup
History of electric power transmission wikipedia , lookup
Audio power wikipedia , lookup
Power MOSFET wikipedia , lookup
Printed circuit board wikipedia , lookup
Transformer types wikipedia , lookup
Schmitt trigger wikipedia , lookup
Stray voltage wikipedia , lookup
Power electronics wikipedia , lookup
Buck converter wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Surge protector wikipedia , lookup
Voltage regulator wikipedia , lookup
Opto-isolator wikipedia , lookup
Alternating current wikipedia , lookup
Voltage optimisation wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Current mirror wikipedia , lookup
F6 USER MANUAL. Ver1.1E F6 assembly instruction. Attention! This device is powered from the AC main that poses threat for life and health. During the work with a high voltage it is necessary to follow safety measures. The user bears full responsibility for the consequences and possible loss as a result of all their actions. 0. INTRODUCTION. This KIT is based on F6 scheme from Nelson Pass. Detailed information can be found on the sites firstwatt.com and diyaudio.com The scheme contains a number of the additions for the safe operation of the amplifier and speaker. Clip and Ready indications are provided. The offered MULTIKIT is very simple in assembly and tuning. Nevertheless, you must have to possess elementary skills of installation and understanding of electricity. The order of an assembled product is possible. All risks of wrong adjustment, connection, assembling, insufficient qualification of the assembler, force-majeure circumstances, are completely accepted by the customer. Some parts or values can be changed without notices. Claims in subjective parameters of products are not examined. The fact of the order of KIT confirms full acceptance of these conditions. 1. TOOLS, EQUIPMENT, MATERIALS. For performance of assembly operations you need to have minimum: crosswise screw-driver, nippers, six-sided key and soldering iron (60-100W). For adjustment operations the multimeter is sufficient. Variac, oscilloscope and the generator are desirable. From materials the screened wire and an assembly wire (14-17AWG) will be required. Solder, flux, shrink tube and plastic ties. 2. PCB ASSEMBLING. Install according to the scheme and component placement card the demanded components in the corresponding positions. Lastly install semiconductors, power cap, output transistors and wires. VD1 and VD2 can be replaced with two serial connected LED’s (white or blue). It is also possible to use reverse-biased junction of low power transistor. While soldering avoid overheating of components carry out the soldering for no longer than 3-4 seconds. Do not allow cold solder joints, short circuits. Do not inhale fumes of solder, work in the aired room. After assembling make sure there are no mistakes in the cold solder joints, or short circuits. 3. ASSEMBLY OF THE AMPLIFIER. Before installation it is necessary to put on output transistors the insulating pad with thermal paste. Use mica or ceramic only! Thickness of paste has to be minimal - surplus is extremely harmful. Attach PCB with four screws. Install transistors clips. Lock in the corresponding screws by sufficient effort by means of a six-sided key. Connect indication PCB, level regulators, input and output connectors according to the assembly diagram. On the chassis install the transformer (transformers) with the isolating gaskets. Connect a main 220VAC according to the assembly diagram. Isolate solder places with help of shrinkable tube. Do not connect secondary windings. After completion of assembly works make sure of lack of mistakes. Example of assembling: 4. ADJUSTMENT OF THE AMPLIFIER. Before power up: Connect the transformer to the adjusted channel. Adjust R7 and R8 resistors in the minimum resistance position. Check resistance – values must be no more than 1 Ohm. Connect the voltmeter between XN9 (Out) and XN10 (GND). Power up the amplifier. Voltage must be close to zero. Voltage on R23 and R24 resistors has to be close to zero. If is not present - immediately power off and look for mistakes. Slowly rotate the R8 resistor before appearing voltage in a point of XN4 (Out) of -50-100 mV. Then slowly rotate the R7 resistor before reduction of voltage to 0 mV. Measure voltage on R23 and R24 resistors- within 0.1– 0.14B (current 1.0– 1.4A) Consecutive adjustments of R7 and R8 resistors achieve output voltage in limits +/-10mV and the demanded voltage on R23 and R24 resistors. Final adjustment is made on heated-up amplifier. Thermal changes of this voltage are normal. Position of the R21 and R22 resistor defines structure of harmonic distortions and the corresponding coloration. You can execute this adjustment depending on your preferences. 5. PROTECTION. This KIT is equipped with output transistors overcurrent protection. There is an opportunity to exclude protection. For a complete elimination of protection you need to remove VT5 and VT5 transistors. However, the system of protection has slight influence only on the tiniest nuances of sound transmission. But the risk of damage of the amplifier and destruction of the speaker system sharply increases. Therefore I do not recommend protection mechanisms eliminating. © StD 2015