Download esr - Slot Tech

What Is ESR Meter And Why Every
Repairer Must Have One For Testing
Electrolytic Capacitors
Testing electrolytic capacitor on board with Capanalyser 88A ESR Meter
All electronic repairers must have esr meter on their repair bench because this special
‘gem’ really can help you to test, troubleshoot and repair electronic equipment faster
especially testing electrolytic capacitors on board or in-circuit. Before I explain in
details about how good this tester is, why not understand the meaning of ESR first.
All capacitors have a certain amount of resistance to the passage of AC current, the
ESR which stands for Equivalent Series Resistance is the total of all internal
resistances of a capacitor measured in Ohms.
An ideal capacitor has 0 ohms ESR. The bottom diagram showed a resistor in series
with a “perfect capacitor”. The value of this resistor is called ESR. It is a must for
technicians to check electrolytic capacitors with esr meter otherwise they might not be
able to find the caused of the problem.
If you have any electronic equipment that over the years has degraded in its
performance such as no power, a newly replaced components burnt after running for
sometimes then chances are good that one or more electrolytic capacitors inside the
equipment has failed, causing the problem. Electrolytic capacitors ESR ohms value
could increase due to drying or corrosion in its material.
Capacitor with high ESR ohms value is a frequent problem in today’s electronic
circuit. In certain circuit (especially dealing with frequency), even a slight increased
in ESR value can cause the whole equipment to stop working and causing intermittent
problems as well. Usually a good electrolytic capacitor (depending on the microfarad
) have a low ESR value, which stays that way for many years unless the rubber seal is
faulty (due to heat or excessive voltage), in which case the electrolyte’s component
gradually dries out and the ESR value will rise up with time.
The rise in ESR value increases both voltage
drops within the capacitor and the heat,
produced in the capacitors due to resistive
heating. If you don’t test electrolytic cap for
ESR, you may not be able to solve the problem.
A high ESR value is the first indicator of
capacitor’s failure.
As mentioned above, when the capacitor ages,
the ESR value will increase and it often does so
in such a dramatic way that the equipment
completely stop functioning or even blows up
any components that directly connected to it. It's
also very common to find capacitors that the esr
value have increased so much of their normal
resistance, yet the capacitance value remains the
same!
You may ask why should I use esr meter? Because checking electrolytic capacitors
with an analogue or digital capacitance meter can MISLEAD an electronic repairer
into believing that a faulty capacitor is good. This will surely waste your faultfinding
time because they could not locate the culprit! If you don’t measure the ESR value of
a capacitor, you will always miss the bad capacitor! Normally, these bad capacitors
have high ESR reading which your normal meter or digital capacitance tester can’t
test it.
Only by using the ESR tester, you will be able to test the ESR on capacitors and you
will not be fooled by capacitors with bad ESR (high ESR value). Another good news
is that the ESR meter can even test capacitor on board, which means you don’t need
to remove the capacitor from circuit board in order to test it with a normal capacitor
meter. Even if you get a good reading testing the capacitance value with a digital
capacitance meter, if the ESR value out, the capacitor is still considered bad!
By the way, do you know that ESR meters can perform other wonders besides
checking the ESR of a capacitor? Some designed of ESR meter have the capabilities
to:
Test low ohms resistor such as 0.1 ohm, 0.27 ohm and so forth.
Check horizontal yoke coil winding of a cathode ray tube,
inductors and primary winding of a power transformer – If a
shorted turn is detected, the inductance drops dramatically and
the esr meter will indicate ohms reading. A good coil will not
have any reading testing with esr meter.
Measure horizontal output transistor (HOT) in a Monitor or
Television – Just like testing a HOT on board with an analog
meter, if an open-circuit reading is obtained, the short-circuit is
elsewhere. If the short-circuit remains, the transistor is
defective.
Fault finding short-circuit in the track, usually will trace to the
bad components - You can utilize the ESR meter to locate
short-circuits on electronic boards by checking the actual track resistance. One probe
connects to the ground and the other to the circuit line and if the measurement rises as
you probe further along the track, you know that you are heading to the wrong
direction! If the esr value decreases as you move along the track then you are in the
right direction.
Test speakers, amplifier and other equipment The pulses generated by the meter have a fast
rise and fall time, so it would probably make a
crude RF signal injector as well.
Check the condition of both the normal and
rechargeable batteries – A worn out, flat and
defective batteries will usually have high ESR
value. Compare with a known good one and
you will easily differentiate a good from the
bad batteries.
Although in the market currently selling lots of
brand of ESR meter such as bob parker dick
smith esr meter, EDS Capanalyser 88A, Tenma, B& K precision, Sencore and many
more, I suggest that you get one according to your own budget. If you diligently surf
the internet for technical homepage and website, you will find some interesting free
esr meter schematic where you can build one for yourself.