* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Sustainable residential building issues in urban heat islands
Survey
Document related concepts
Building material wikipedia , lookup
Zero-energy building wikipedia , lookup
Sustainable urban neighbourhood wikipedia , lookup
Sustainable city wikipedia , lookup
Thermal comfort wikipedia , lookup
Green building wikipedia , lookup
Urban ecology wikipedia , lookup
Geothermal heat pump wikipedia , lookup
Building insulation materials wikipedia , lookup
Sustainable landscaping wikipedia , lookup
R-value (insulation) wikipedia , lookup
Reflective surfaces (climate engineering) wikipedia , lookup
Autonomous building wikipedia , lookup
Thermal management (electronics) wikipedia , lookup
Urban resilience wikipedia , lookup
Passive house wikipedia , lookup
Transcript
Page 1 of 8 SB10 New Zealand SUSTAINABLE RESIDENTIAL BUILDING ISSUES IN URBAN HEAT ISLANDS – THE POTENTIAL OF ALBEDO AND VEGETATION ALAMAH MISNI1, PENNY ALLAN2 1 University of Technology Mara, Malaysia Victoria University of Wellington, New Zealand __________________________________________________________________________________ 2 TYPE OF PAPER Scientific Student Paper ABSTRACT The ‘urban heat island effect’ influences most of the major cities around the world. This heat island phenomenon contributes to discomfort and increased air conditioning loads. On hot summer days, this effect significantly contributes to the urban dweller’s discomfort, resulting in an increase in energy bills due to increased requirements for cooling. This paper evaluates the potential for light colour surfaces and landscape design of single family domestic dwellings to significantly minimise the energy demands associated with air conditioning in the urban environment. Light coloured surfaces reflect solar radiation and reduce heat absorbed by buildings. Modification of the value of ‘albedo’ (the measure of a surface’s reflectivity) of a building’s envelope and in particular walls and roof, can potentially reduce the ambient temperature in an individual building and its surroundings and keep the entire neighbourhood cool. This research reveals that urban albedo can achieve a decrease of up to 2°C in air temperature, and reduce home energy use by as much as 50%. In a single family residence, substantial cooling energy and capacity savings can also be achieved by the direct shading of walls, windows, and roofs by vegetation. The appropriate amount, type, and placement of vegetation can save as much as 55% of residential cooling demand on a hot summer day and reduce surrounding air temperatures by as much as 5°C. Results indicate that the largest reduction of energy consumption occurs with modifications in reflective building envelopes and strategically positioned vegetation around buildings. This reduces cooling requirements for building and neighbourhood areas. Both trees and light colour material surfaces can have significant effect on the temperatures and energy consumption of buildings. A combination of two mitigation strategies, landscaping and albedo modification can create communities that are cooler, more aesthetically pleasing, and more energy efficient. KEYWORDS: Urban heat island effect; albedo; vegetation; energy consumption; single family domestic dwellings INTRODUCTION The ability of a city to generate an urban heat island is now well documented. The urban heat island effect, together with summertime heat waves, sets in motion conditions that foster biophysical hazards such as heat stress and increased concentration of secondary air pollutants (Solecki et al., 2005). The implementation of urban heat island mitigation strategies can reduce the impacts of biophysical hazards in cities including heat stress related to elevated temperatures, air pollution and associated public health effects. Two basic strategies to mitigate urban heat island are high-albedo surface material and increased vegetative cover. Using light coloured surfaces is potentially the simplest strategy for saving peak energy and improving the quality of the environment in urban areas. Building envelopes and their environments have a significant effect on thermal comfort and energy use. One of the most important factors affecting building envelope design and its local environment is climate. The building envelope can be considered the selective pathway for a building to work with the climate and respond to heating, cooling, ventilating, and natural lighting needs (DOE 2004 cited in Okba, 2005). An optimal design of the building envelope may provide significant reductions in cooling and heating loads. Each type of climate will require different building SB10 New Zealand Page 2 of 8 envelope design strategies. Specific designs and materials can potentially provide solutions for any given climatic conditions. The use of light coloured surfaces on buildings and outdoor urban areas is potentially practical in areas which have large amounts of sunshine. Sustainable design of the built environment along with careful landscaping can create cooler communities and save energy. Careful landscape planning can reduce the amount of sunlight heating building surfaces and can prevent reflected heat-causing light from entering the home. Architects can create a microclimate boundary by manipulating the building envelope and exterior environment (Bomberg and Brown, 1993). The planning and development of exterior spaces can reduce the energy consumption of buildings by reducing the adverse impact of some climate factors. If the microclimatic condition around the building is very similar to the desired interior condition, little extra energy is required. Conversely, if the microclimate is significantly different from the desired interior conditions, large amounts of energy may be required for heating or cooling (Brown and Gillespie, 1995). However, proper landscaping can also be used to improve thermal performance. It reduces the amount of radiation falling on the building by shading, by moderating temperatures, by the evapotranspiration processes, and by controlling wind direction to assist in keeping the building warm or cool. This paper describes the heat island phenomenon, sensible heat flow, the importance of light coloured surfaces and albedo, and the potential of vegetation to reduce the impacts of the urban heat island effect. THE URBAN HEAT ISLAND EFFECT The urban heat island effect is well documented as an urban phenomenon where air temperatures in densely built urban areas are higher than the temperatures of the surrounding rural country. The larger the city, the more intense the summer heat island effect (Oke, 1973) and the magnitude of discomfort and associated air conditioning load (Akbari et al., 1986). The heat island effect is caused by complex interactions between many factors including decreased urban albedo, increased thermal mass per unit area, increased city roughness (the roughness elements of a city are its buildings whose heights generally increase toward the city centre), anthropogenic heat released from buildings and vehicles, and decreased evaporative areas (Taha et al., 1988). All these factors affect the energy and moisture balance in urban areas. This process decreases the proportion of latent heat in comparison with the sensible heat in accordance with the Bowen ratio, which in turn leads to higher ambient air temperature. The Bowen ratio relates to the ratio of sensible to latent heat fluxes of energy balance. On hot summer days, this effect significantly contributes to the urban dweller’s discomfort resulting in an increase in energy bills due to the increased requirements for cooling. As humans alter the character of the natural landscape in the city-building process, the local energy exchanges that take place within the boundary layer are affected. Therefore, modification of the landscape influence the microscale, mesoscale, and macroscale climate. The best-known effect of urban areas on heat islands is the so-called "microclimate" created in city centres. In urban areas, building and paved surfaces have gradually replaced pre-existing natural landscapes. As a result, solar energy is absorbed and stored within building structures, roads, and other hard surfaces during the daytime. The absorbed heat is subsequently re-radiated to the surroundings and increases ambient temperatures at night causing the surface temperature of urban structure to become 5.5–10°C higher than surrounding areas because dust and clouds act like a blanket to keep it in (Akbari et al., 1992). As the surface throughout an entire community becomes hotter, the overall ambient air temperature increases by 2–8°C. Higher average temperatures also mean that city centres experience less snow and fewer frosts than either their suburbs or the surrounding rural area. The higher levels of cloud cover and dust pollutants in the atmosphere mean that city centres also have higher rainfall levels and more fogs than adjacent rural areas. Urban heat islands are considered as a mild asset in winter and can reduce the demand for heating. However they can significantly increase the demand for cooling energy during the summer. SB10 New Zealand Page 3 of 8 SENSIBLE HEAT FLOW Local climate affects the rate of heat gain from buildings by contribute to heat flows throughout our environment. There are three ways the heat can be transmitted through any medium: conduction, convection, and radiation. Conduction involves the transformation of kinetic heat in solid mass. This is the process of heat transfer from warmer to cooler molecules within a solid material. The heat flows through materials or building fabric from which a home is built. The primary heat transfer paths between a building and its external environment are: conduction through walls, roofs, doors (opaque conduction) and windows (glazed conduction); solar radiation directly penetrating through windows; and sensible and latent heat gain from air exchange. Convection represents the transfer of heat by circulation or movement of hot particles to cooler areas. Heat transfer by convection can occur in liquids and gases when molecules move freely and independently (Moss, 2007). Convective heat exchange occurs in several situations: when heat is transferred from a solid to the adjacent air, or heat transfer between two surfaces at different temperatures by means of airflow. Convection is caused by two types of forces: by temperature difference (natural) and forced air motion generated by wind or fans. Convective heat transfer takes place when the building is infiltrated by wall surfaces, when outdoor air flows through the interior space. If the ambient temperature is different from the temperature of any element of the interior space, convective heat transfer takes place. Radiation occurs without the involvement of a physical substance as the medium. Thermal radiation involves the interchange of electromagnetic waves between surfaces of differing temperature (Moss, 2007). The sun transfers its heat to the surface of the earth by radiation through space to the earth’s atmosphere. The ozone layer, atmospheric particles, condensing water vapour and dust, act as a filter to solar radiation, reducing its intensity at the earth’s surface. Radiant heat transfer in buildings is energy exchanged between surfaces by electromagnetic waves across space. The radiation wave is transmitted through space until it strikes an opaque surface, where it is partly absorbed. The absorbed radiation increases the vibration of the surface molecules and thus raises the temperature of the material where the absorption took place. LIGHT COLOURED SURFACES The use of light coloured surfaces on building and outdoor urban areas is potentially practical in areas which have a large amount of sunshine. Light coloured surfaces reflect solar radiation and reduce the heat absorbed by buildings. Through modification, the suitable value of albedo for a building envelope, particularly walls and roof, can potentially reduce the ambient temperature in an individual building and its surroundings and keep the entire neighbourhood cool. Walls. Walls are a major part of the building envelope, usually a solid structure of masonry, wood, plaster, or other building material. Walls have two main purposes: to support roofs and ceilings, and to divide space, providing security against intrusion and weather. In addition, the wall may house various types of electrical wiring or plumbing. Electrical outlets are usually mounted in walls. In conventional construction, a building wall will usually have the structural elements, insulation and finishing elements, or surface. The wall thickness, material and finishes can be chosen based on the heating and cooling needs of the building. Appropriate thermal insulation and air cavities in a wall reduce heat transmission into the building. During the summer, walls receive large amounts of solar radiation. The thermal comfort conditions for buildings depend on the heat storage capacity and heat conduction properties of walls. Walls are the biggest surfaces of buildings. White exterior walls absorb less heat than dark walls. Therefore, wall surfaces play a large role in temperature and modification of energy consumption. Modification of the albedo of walls is simplest, it only require routine painting. Roof. A roof is the top covering on the uppermost part of the building envelope. A roof protects the building from the effect of weather such as rain, the high summer sun, and also from snow melt coming off the roof. Roof designs come in 'pitched', 'low slope' or 'flat' forms. Roof shapes and pitches are often the SB10 New Zealand Page 4 of 8 product of design, material constraints and climatic considerations. Pitched roofs are the primary design on residential buildings. About a third of the unwanted heat that builds up in homes comes in through the roof (DOE, 1994). The need for greater thermal resistance will dictate the type of roof design. The weather proofing material is the topmost or outermost layer exposed to the weather. Pitched roofs are often covered with asphalt shingles, thatch, wood shake, steel, corrugated galvanised iron, slate, and tiles. Drainage on roofs is typically installed at interior locations or on the exterior wall. Light coloured roofing material has been used to reduce the summer contribution of solar-driven roof gain. Unlike most light coloured surfaces, white asphalt and fiberglass shingles absorb 70% of the solar radiation making them less effective (DOE, 1994). Another way to reflect heat is to install a radiant barrier on the underside of the roof. A radiant barrier is simply a sheet of aluminium foil with a paper backing. When installed correctly, a radiant barrier can reduce heat gains through a ceiling by about 25% (DOE, 1994). One good solution is to apply both waterproof with insulation layer and reflective coating properties to the roof. ALBEDO The measure of a surface’s reflectivity is called albedo. Albedo is the fraction of sunshine (shortwave radiation) reflected from any surface on the earth back into space (Brown and Gillespie, 1995). A light meter is used as a device to measure the amount of light with scale and the unit of light is in lux (measures intensity of light per unit area). The sensor points upward to measure the incident sunlight, and then quickly flips upside down to measure the reflected sunlight. The value of albedo is calculated dividing the second measurement (reflected) by the first measurement (incident). Albedo can assume any value between 0.0 and 1.0 but these limits do not include natural elements. In building surfaces and components, the importance of albedo varies with a location’s latitude. For example in near tropics, the roof assumes the most critical role in sensible heat exchange but in mild climates the effect of exterior colour is further complicated (Taha et al., 1988). An increase in the surface of albedo has a direct impact on the energy balance of the building. Santamouris (2005) states that in all cases the temperatures of reflective roof surfaces are significantly reduced, but the degree to which the cooling load decreases depends on the structure of the roof and on the overall thermal balance of the building. Using high albedo materials reduces the amount of solar radiation absorbed through building envelopes and urban structures and keeps their surface cooler, for example, white elastomeric coatings (with an albedo of 0.72) were 45°C cooler than black coating (with an of albedo 0.08) in the early afternoon of a clear day in summer (Taha, 1997). Taha also added that using a white surface with an albedo of 0.61 was only 5°C warmer than ambient air whereas conventional gravel with an albedo of 0.09 was 30°C warmer than air. For example, the temperature of dark coloured insulated residential building surfaces in Washington DC was about 8°C higher than light colour surfaces during peak time at 14.00 hours (Connor 1985, cited in Taha et al., 1988). In general, light-coloured surfaces have high albedo and dark-colour surfaces have low albedo. The reduction of surface temperature also reduces the intensity of long wave radiation. Local and downwind ambient air temperatures can be lower because of smaller convective heat fluxes from cooler surfaces. Computer simulation shows that reasonable increases in urban albedo can achieve a decrease of up to 2°C in air temperature (Taha, 1997). Reductions in temperatures and energy use from albedo modifications relate to both individual buildings and entire neighbourhoods (Akbari et al., 1992). Modifying the albedo material by using light-coloured surfaces on a building will potentially lower the heat build-up from sunlight on the wall and roofs, and reduce the amount of electricity needed for air-conditioning. The effect of albedo on building energy use can be categorised as either local or global. According to Taha et. al. (1988), local or direct effects refer in particular to the modifications in reflective building envelopes. Global or indirect effects refer to micro-climatic changes where urban albedo is modified mainly in dry bulb temperature. Akbari (1992) found that from computer simulation of an individual typical house in Sacramento, the total air-conditioning bill could be reduced by up to 20% if the albedo of the walls and roofs were increased from a typical 0.30 to a light-coloured 0.90. Akbari states that if similar albedo modifications were implemented in large scale urban surfaces, the result would be an indirect impact of lowered air temperature in the neighbourhood. Akbari showed that the indirect cooling energy saving for typical houses could be 3–5% for each 0.01 increase in overall city albedo. When the direct and indirect savings of albedo changes were combined, the simulated total energy saving approached 50% SB10 New Zealand Page 5 of 8 during average hours and 31% during peak cooling period (Akbari et al., 1992). Ahbari revealed these simple changes in albedo levels can reduce home energy use by 10–50% (1992). The studies show that using albedo can potentially create comfortable environments for buildings and reduce heat in air temperature. It can save energy by reducing air-conditioning during summer in temperate climates and in hot climates. POTENTIAL OF URBAN VEGETATION Vegetation affects urban climates and building thermal performance and energy by shading, by lowering and channelling wind speeds, and by evapotranspiration. It modifies the thermal interaction between a building and its surroundings. Shade. Tree shading is the cover or shelter provided by the interception of trees and solar radiation. Using shade effectively depends on the species, and density of the tree and the size, foliage, shape, and location of the moving shadow that it casts. According to Akhbari et al. (1992), tree shade reduces cooling energy use inside a building in three ways. First, window shading helps prevent direct solar radiation from entering the interior of the house. Second, shading the walls, windows, and roofs keeps them from getting hot, thereby reducing the amount of heat reaching the interior. Third, shade keeps the soil around the building cool. Efficient shading will be achieved when trees are placed strategically. For example, at 40°S Latitude evergreen trees should be placed on the northeast and west sides of the building. The best locations for deciduous trees in the northern hemisphere are on the south and west sides of a house. During summer, trees will cast long shadows which can be utilised effectively on those sides which are otherwise difficult to protect from the sun’s heat at this time of the day. When these trees drop their leaves in the winter, sunlight can reach the house to help in heating the home. Trees with high, spreading crowns can be planted to the south of a building to provide maximum summertime roof shading. Trees with crowns closer to the ground are more appropriate to the west, where shade is needed from lower afternoon sun angles. Evergreen trees on the north and west sides afford the best protection from the setting summer sun and shelter from cold winter winds. In addition to the obvious use of shade trees to provide relief from the summer sun, properly placed trees can channel summer breezes to desired locations. The type, foliage, and species of trees used are very important. Trees should be selected according to the amount and type of shade they provide. Solar heat passing through windows and being absorbed through the roof is the major reason for airconditioner use. Shading is the most cost-effective way to reduce solar heat gain and air-conditioning costs. Field measurements have suggested that the shade of trees and shrubs planted immediately adjacent to buildings can directly reduce cooling loads (Simpson and McPherson, 1996). Their study in Sacramento showed that trees shading a west exposure from afternoon sun had the greatest impact on cooling savings for all climate zones and insulation levels. In a single family residence, substantial cooling energy and capacity savings can be achieved due to the direct shading of walls and roofs. Akbari et al.’s (1986) study in Los Angeles stated that planting trees can save as much as 34% of residential cooling energy on a hot summer day. They added that the net effect of shade in warm climates was beneficial. Buffington’s (1980) study showed that the effect of uniform shading on the walls and roofs of a concrete block residence in central Florida reduced annual cooling by 14%. Heisler (1984) stated that the average reductions of solar radiation on walls on conventional houses in Davis, California, in the shade of midsize dense trees, may be 30-35% on sunny days, while the reduction in the shade of large trees may be 45%. Parker (1983) described that in his study of a child care centre at Florida International University, Miami, landscaping reduced air conditioning costs during warm summer days by approximately 58%. The magnitude of these savings suggests that trees and shrubs reduce cooling requirements not only by shading but also by reducing warm air infiltration and creating cool microclimates by evapotranspiration near the residence. Proper landscaping around the home can potentially provide shade to save energy and reduce the urban heat island effect. Wind modification. During summer, wind is an asset which can provide natural ventilation and convective cooling of hot exterior building surfaces. Olgyay (1963) suggests that wind is particularly important for comfort when temperatures are above 29°C and relative humidity above 50%. In these cases, cooling needs are high and landscaping around the buildings should be directed towards channelling SB10 New Zealand Page 6 of 8 cooling breezes, and to minimize humidity close to the home. Heat removal from a building during the warmer months can be influenced by the placement of plants, and by their shape. Airflow can be increased by strategically locating a combination of hedgerows, and tree canopies. McPherson, Herrington and Heisler (1988) suggest that high-branching and wide canopy trees and low ground covers should be used to promote shade and encourage wind. Trees with tall trunks and spreading canopies in combination with grasses and low flower beds are the most effective planting for providing usable shade and influencing the movement of wind around and through a building. Directing wind through a building and against the walls and roof permits rapid removal of heat. The effect of vegetation on wind conditions depends to a great extent on the type of the vegetation, and on the details of the planting pattern. Properly selected and placed landscaping can provide excellent wind channelling during summer. This will reduce cooling costs considerably. During the summer, strategically planting trees in urban housing areas can act as a wind channel and potentially have a substantial impact on a residential building’s energy performance. Evapotranspiration. Evapotranspiration is the combined loss of water from vegetation to the atmosphere by evaporation and transpiration. This is a major mechanism through which trees contribute to decrease urban temperatures (Santamouris, 2001). Evaporation accounts for the movement of water to the air from sources such as soil, canopy interceptions, and water bodies. Transpiration accounts for the movement of water within a plant and the subsequent loss of water as vapour through the stomata of leaves. Transpiration puts moisture into the air and moderates air temperature changes. Evapotranspiration can create oases that are 2–8ºC cooler than their surroundings (Oke, 1988). The oasis effect is a change in the microclimatological conditions in a vegetated area as distinguished from an area without vegetation (Saaroni et al., 2004). The change is manifested in lower temperatures and higher relative humidity (Oke, 1988). Oke describes green areas as more humid. These processes increase the proportion of latent heat in comparison with the sensible heat in accordance with the Bowen ratio. However, the amount of water that plants transpire varies greatly geographically and over time. It is determined by a number of factors such as temperature, relative humidity, wind, air movement, soil-moisture availability, and type of plant. Temperature is an important aspect of transpiration. Temperature can control the opening of the stomata. Higher temperatures cause the plant cells to open allowing water to be released to the atmosphere, whereas colder temperatures cause the openings to close. As the relative humidity of the air surrounding the plant rises, the transpiration rate falls. When water transpires from a leaf, the water saturates the air surrounding the leaf. Wind movement will increase the movement of air around a plant and this will result in a higher transpiration rate. Shade from vegetation also prevents direct radiation from reaching the ground surface and warming it, thereby resulting in lower air temperatures above these surfaces. As a result, when shade is combined with evapotranspiration process, the air temperatures near the ground in green areas will be lower. The evapotranspiration process from vegetation contributes significantly to cooling cities and saving energy. The lower evapotranspiration rate in urban areas is a major factor in increasing daytime temperatures. The evapotranspiration process is predominantly effected and monitored surrounding air temperatures. Vegetation produces evapotranspiration around individual houses and their neighbourhood areas, thus reducing urban temperatures at the microclimatic scales. If ample soil moisture is present and environmental conditions are suitable, water in the leaves evaporates and the air is cooled. Heisler has stated that trees are effective for cooling because they absorb 70–85% of the heat from solar radiation by transpiration (cited in Akbari et al., 1992). According to Taiz and Zeiger (2006), leaves absorb about 50% of the total solar energy. Since leaves are generally dark and coarse and thus reflect very little light, they make ideal solar radiation absorbers and controllers. Temperature measurements in suburban Davis and Sacramento, indicate that the air temperature in neighbourhoods with mature tree canopies are 3–6°F lower in daytime than newer areas with no trees (Akbari et al., 1992). Similarly, groundcovers such as grasses or turf also have a cooling effect from evapotranspiration. The temperature above a groundcover can be 10– 15°F cooler than above a heat absorbent material (Morgan et al., 2000). Computer simulations have shown that residential neighbourhoods with extensive vegetation can reduce air temperature by as much as 10ºF compared with nearby areas with little vegetation (McPherson and Simpson, 1995). The amount of tree cover and its placement influences the reduction in cooling energy. Huang et. al. (1987) studies in the USA found that a 10% increase in tree cover per house would result in a cooling energy reduction of 24% in Sacramento, 12% in both Phoenix and Lake Charles. A 25% increase in tree cover, corresponding to three trees per house on the southeast and west sides, was estimated to have an even more dramatic impact SB10 New Zealand Page 7 of 8 with reductions in cooling energy use of 57% in Sacramento, 17% in Phoenix, and 23% in Lake Charles. Huang et al. (1987) found that the direct effect of shading accounted for only 10–35% of the total cooling energy saving; the remaining savings were due to evapotranspiration. This confirms that a minimum of a mature tree strategically placed around residential buildings, combined with groundcovers can reduce urban heat islands effects and cooling energy use, and can create a comfortable place for house interior and their surrounding. CONCLUSION The major factors increasing daytime temperatures and creating heat island in a residential area are low albedo in the building envelope and lower vegetative planting around buildings. Proper house configuration and surrounding landscaping also can influence thermal performance and energy use. Simple changes in albedo levels can reduce home energy use by 10–50%. Using high-albedo surface materials can potentially create a comfortable environment for buildings, and reduce air temperature, and save energy by reducing air-conditioning during summer. Vegetation reduces the cooling requirements not only by shading but also by reducing warm air infiltration and creating cool microclimates around buildings by evapotranspiration. In addition, during the summer season, vegetation in urban housing areas can act as a wind channel and potentially have a substantial impact on a residential building’s energy performance. Vegetation can reduce temperature and energy use by doubling the amount of albedo modification on building. By combining of every type of vegetation and strategically placed with right amount, size, species and form around residential buildings will save energy and produce a more comfortable house, and can reduce urban heat island effects to the surrounding city. Therefore, mitigating strategies such as using high-albedo surface material for the building envelope, and increased urban vegetative cover aimed at reducing temperatures and energy use will become increasingly important under dynamic climate conditions. ACKNOWLEDGEMENTS The authors gratefully acknowledge Professor Dr George Baird, at School of Architecture, Victoria University of Wellington, New Zealand, for very helpful and valuable review comments. REFERENCES: AKBARI, H., DAVIS, S., DORSANO, S., HUANG, J. & WINNET, S. (1992) Cooling our Communities, A Guidebook on Tree Planting and Light-Colored Surfacing Washington, Lawwrence Berkeley Laboratory AKBARI, H., TAHA, H., HUANG, J. & ROSENFELD, A. (1986) Undoing uncomfortable summer heat islands can save gigawatts of peak power. The Panel on Small Building Technologies. Washington, DC, American Council for an Energy-Efficient Economy. BOMBERG, M. T. & BROWN, W. C. (1993) Building Envelope and Environmental Control: Part 1Heat, Air and Moisture Interactions. Construction Canada, 35, 15-8. BROWN, R. D. & GILLESPIE, T. J. (1995) Microclimatic Landscape Design Creating Thermal Comfort and Energy Efficiency New York John Wiley & Sons, Inc. BUFFINGTON, D. E. (1980) Economic analysis of the effectiveness of various landscaping and structural features for reducing energy expenditures for heating and cooling residential buildings in each of 9 areas in Florida. Proceedings of Alternative Energy Sources for Florida, Gainesville. Florida. DOE (1994) Cooling Your Home Naturally. Energy Efficiency and Renewable Energy Clearinghouse. USA, MocroAssist. SB10 New Zealand Page 8 of 8 HUANG, Y. J., AKBARI, H., TAHA, H. & ROSENFELD, A. H. (1987) The potential of vegetation in reducing summer cooling loads in residential building. Climate and Applied Meteorology 26, 1103-16. MCPHERSON, E. G., HERRINGTON, L. P. & HEISLER, G. M. (1988) Impacts of vegetation on residential heating and cooling Energy and Buildings, 12, 41-51. MCPHERSON, G. & SIMPSON, J. R. (1995) Shade Trees as a Demand-Side Resource. Several utilities have embraced trees as a solar-powered demand-side management resource. Home Energy MORGAN, R., MCLEOD, M., MAYFIELD, J., RICHMOND-POWERS, M., COHEE, B., GROS, L., SHAVER, R., SCANLON, M., BARNETT, S. & NUTT, L. (2000) Supplement to the Green Building Program, Austin, Texas Green Building Program. MOSS, K. J. (2007) Heat and Mass Transfer in Buildings, New York Taylor & Francis OKBA, E. M. (2005) Building envelope design as a passive cooling technique. International Conference “Passive and Low Energy Cooling for the Built Environment”. Santorini, Greece. OKE, T. R. (1973) City size and the urban heat island. Atmospheric Environment (1967), 7, 769-779. OKE, T. R. (1988) Boundary Layer Climates, London Routledge Taylor & Francis Group OLGYAY, V. (1963) Design with Climate Bioclimatic Approach to Architectural Regionalism New Jersey Princeton University Press PARKER, J. H. (1983) The effectiveness of vegetation on residential building. Passive Solar Journal 2. SAARONI, H., BITAN, A., DOR, E. B. & FELLER, N. (2004) The mixed results concerning the [`]oasis effect' in a rural settlement in the Negev Desert, Israel. Journal of Arid Environments, 58, 235-248. SANTAMOURIS, M. (2001) The role of green spaces. IN SANTAMOURIS, M. (Ed.) Energy and Climate in the Urban Built Environment. London James & James (Science Publishers) Ltd. SANTAMOURIS, M., P.WOUTERS, LONCOUR, X., AKANDER, J., GUDNIJOHANNESSON, ALVAREZ, S., BLANCO, A., SANZ, J. A. & SANCHEZ, F. J. (2005) Energy Performance of Residential Buildings, London James & James/Earthscan. SIMPSON, J. R. & MCPHERSON, E. G. (1996) Potential of tree shade for reducing residential energy use in California Journal of Arboriculture 22, 10-8. SOLECKI, W. D., ROSENZWEIG, C., PARSHALL, L., POPE, G., CLARK, M., COX, J. & WIENCKE, M. (2005) Mitigation of the heat island effect in urban New Jersey. Global Environmental Change Part B: Environmental Hazards, 6, 39-49. TAHA, H. (1997) Urban climates and heat islands: albedo, evapotranspiration and anthropogenic heat. Energy and Building 25, 99-103. TAHA, H., AKBARI, H., ROSENFELD, A. & HUANG, J. (1988) Residential Cooling Loads and the Urban Heat Island - the effects of Albedo. Building and Environment. TAIZ, L. & ZEIGER, E. (2006) Plant Physiology Massachusetts, Sinauer Associates, Inc