Download EE2251-Electrical Machines I

MAHAKAVI BHARATHIYAR COLLEGE OF ENGINEERING AND TECHNOLOGY
EE2251 Electrical Machines-I
SHORT QUESTIONS AND ANSWERS
UNIT-1
1. What is magnetic circuit?
The closed path followed by magnetic flux is called magnetic circuit
2. Define magnetic flux?
The magnetic lines of force produced by a magnet is called magnetic flux it is denoted
as Ф and its unit is Weber
3. Define magnetic flux density?
It is the flux per unit area at right angles to the flux it is denoted by B and unit is
Weber/m2
4. Define magneto motive force?
MMF is the cause for producing flux in a magnetic circuit. the amount of flux setup in
the core decent upon current(I)and number of turns(N).the product of NI is called
MMF and it determine the amount of flux setup in the magnetic circuit
MMF=NI ampere turns (AT)
5. Define reluctance?
The opposition that the magnetic circuit offers to flux is called reluctance. It is defind
as the ratio of MMF to flux. It is denoted by S and its unit is AT/m
6. What is retentivity?
The property of magnetic material by which it can retain the magnetism even after the
removal of inducing source is called retentivity
7. Define permeance?
It is the reciprocal of reluctance and is a measure of the cause the ease with which flux
can pass through the material its unit is wb/AT
8. Define magnetic flux intensity?
It is defined as the mmf per unit length of the magnetic flux path. it is denoted as H
and its unit is AT/m
H=NI/L
9. Define permeability?
Permeability of a material means its conductivity for magnetic flux. Greater the
permeability of material, the greaters its conductivity for magnetic flux and vice versa
10. Define relative permeability?
It is equal to the ratio of flux density produced in that material to the flux density
produced in air by the same magnetizing
force µr=µ/µ0
11. What is mean by leakage flux?
The flux does not follow desired path in a magnetic circuit is called leakage flux
12. What is leakage coefficient?
Leakage coefficient=total flux/useful flux
13. State faradays law of electromagnetic induction
Whenever a flux linking in the coil changes emf always induced in the conductor the
magnitude of induced emf is proportional to rate of change flux
linkage e = NdФ/dt
14. State Lenz law?
The law states that induced emf always opposite to applied voltage source
15. Define self inductance?
The property of a coil that opposes any change in the amount of current flowing
through it is called self inductance
16. Define mutual inductance?
The property of a coil to produce emf in a coil due to change in the value of current or
flux in it is called mutual inductance
17. Define coefficient coupling?
It is defined as the fraction of magnetic flux produced by the current in one coil that
links the other coil
18. Give the expression for hysteresis loss and eddy current loss?
1.62
Hysteresis loss=kh b max fv watts
Eddy current loss=kebmax2f2t2v watts/unit volume
19. What is dynamically induced emf?
An induced emf is produced by the movement of the conductor in a magnetic field.
this emf is called dynamically induced emf. The dynamically induced emf
e =Blvsinϴ
20. What is fringing effect?
It is seen that the useful flux passing across the air gap tends to buldge outwords, there
by increasing the effective area of the air gap and reducing the flux density in the gap
is called fringing effect
21. State two types of IM?
1. Squirrel cage IM
2. Slip ring IM
22. State ohms law for magnetic circuits?
Ohms law for magnetic circuits mmf=flux X reluctance
23. What is statically induced emf?
Conductor is stationary and the magnetic field is moving or changing the induced emf
is called stationary induced emf
24. How eddy current losses are minimized?
By laminating the core’
25. State types of electrical machines?
1.DC machines
2.AC machines
3.Special machines
26. What is mean by stacking factor?
Magnetic cores are made up of thin, lightly insulated laminations to reduce the eddy
current loss. As a result, the net cross sectional area of the core occupied by the
magnetic material is less than its gross cross section; their ratio being is called the
stacking factor. The stacking value is normally less than one .its value vary from 0.5 to
0.95 .the stacking factor value is also reaches to one as the lamination thickness
increases
27. What are the magnetic losses?
1. Eddy current loss
2. Hysterisis loss
28. Types of induced emf?
1. Dynamically induced emf
2. Statically induced emf
UNIT-2
1. Define a transformer?
A transformer is a static device which changes the alternating voltage from one level to
another.
2 What is the turns ratio and transformer ratio of transformer?
Turns ratio = N2/ N1
Transformer = E2/E1 = I1/ I2 =K
3. Mention the difference between core and shell type transformers?
In core type, the windings surround the core considerably and in shell type the core
surrounds the windings i.e winding is placed inside the core
4. What is the purpose of laminating the core in a transformer?
In order to minimise eddy current loss.
5. Give the emf equation of a transformer and define each term?
Emf induced in primary coil E1= 4.44fФmN1 volt
Emf induced in secondary Coil E2 =4.44 fФmN2.
f-----------freq of AC input
Ф---------maximum value of flux in the core
N1, N2----Number of primary & secondary turns.
6. Does transformer draw any current when secondary is open? Why?
Yes, it (primary) will draw the current from the main supply in order to magnetize the
core and to supply for iron and copper losses on no load. There will not be any current
in the secondary since secondary is open.
7. Define voltage regulation of a transformer?
When a transformer is loaded with a constant primary voltage, the secondary voltage
decreases for lagging PF load, and increases for leading PF load because of its internal
resistance and leakage reactance. The change in secondary terminal voltage from no
load to full load expressed as a percentage of no load or full load
voltage is termed as regulation.
%regulation =E2-V2/E2 *100
V2>E2 for leading p.f load
V2<E2 for lagging p.f load
8. Define all day efficiency of a transformer?
It is computed on the basis of energy consumed during a certain period, usually a day
of 24 hrs. All day efficiency=output in kWh/input in kWh for 24 hrs.
9. Why transformers are rated in kVA?
Copper loss of a transformer depends on current & iron loss on voltage. Hence total
losses depend on Volt-Ampere and not on PF. That is why the rating of transformers is
in kVA and not in kW.
10. What determines the thickness of the lamination or stampings?
1.Frequency
2.Iron loss
11. What are the typical uses of auto transformer?
1.To give small boost to a distribution cable to correct for the voltage
drop. 2. as induction motor starter.
12. What are the applications of step-up & step-down transformer?
Step-up transformers are used in generating stations. Normally the generated voltage
will be either 11kV. This voltage (11kV) is stepped up to 110kV or 220kV or 400kV
and transmitted through transmission lines (simply called as sending end voltage).
Step-down transformers are used in receiving stations. The voltage are stepped down
to 11kV or 22kV are stepped down to 3phase 400V by means of a distribution
transformer and made available at consumer premises. The transformers used at
generating stations are called power transformers.
13. How transformers are classified according to their construction?
1. Core type 2.shell type. In core type, the winding (primary and secondary) surround
the core and in shell type, the core surround the winding.
14. Explain on the material used for core construction?
The core is constructed by sheet steel laminations assembled to provide a continuous
magnetic path with minimum of air gap included. The steel used is of high silicon
content sometimes heat treated to produce a high permeability and a low hysteresis
loss at the usual operating flux densities. The eddy current loss is minimized by
laminating the core, the laminations being used from each other by light coat of coreplate vanish or by oxide layer on the surface. The thickness of lamination varies from
0.35mm for a frequency of 50Hz and 0.5mm for a frequency of 25Hz.
15. How does change in frequency affect the operation of a given transformer?
With a change in frequency, iron and copper loss, regulation, efficiency & heating
varies so the operation of transformer is highly affected.
16. What is the angle by which no-load current will lag the ideal applied voltage?
In an ideal transformer, there are no copper & core loss i.e. loss free core. The no load
current is only magnetizing current therefore the no load current lags behind by angle
900. However the winding possess resistance and leakage reactance and therefore the
no load current lags the applied voltage slightly less than 900.
17. List the arrangement of stepped core arrangement in a transformer?
1. To reduce the space effectively
2. To obtain reduced length of mean turn of the winding
3. To reduce I2R loss.
18. Why are breathers used in transformers?
Breathers are used to entrap the atmospheric moisture and thereby not allowing it to
pass on to the transformer oil. Also to permit the oil inside the tank to expand and
contract as its temperature increases and decreases.
19. What is the function of transformer oil in a transformer?
1. It provides good insulation
2. Cooling.
20. Can the voltage regulation goes –ive? If so under what condition?
Yes, if the load has leading PF.
21. Distinguish power transformers & distribution transformers?
Power transformers have very high rating in the order of MVA. They are used in
generating and receiving stations. Sophisticated controls are required. Voltage ranges
will be very high. Distribution transformers are used in receiving side. Voltage levels
will be medium. Power ranging will be small in order of kVA. Complicated controls
are not needed.
22. Name the factors on which hysteresis loss depends?
1. Frequency 2. Volume of the core 3. Maximum flux density
23. Why the open circuit test on a transformer is conducted at rated voltage?
The open circuit on a transformer is conducted at a rated voltage because core loss
depends upon the voltage. This open circuit test gives only core loss or iron loss of the
transformer.
24. What is the purpose of providing Taps in transformer and where these are
provided?
In order to attain the required voltage, taps are provided, normally at high voltages
side(low current).
25. What are the necessary tests to determine the equivalent circuit of the
transformer?
1. Open circuit test
2. Short circuit test
26. Define efficiency of the transformer?
Transformer efficiency ƞ= (output power/input power) x 100
27. Mention the difference between core and shell type transformers?
In core type, the windings surrounded the core considerably and in shell type the core
surround the windings i.e winding is placed inside the core
28. Full load copper loss in a transformer is 1600W. What will be the loss at half load?
If n is the ratio of actual load to full load then copper loss = n 2 (F.L copper
loss) Pc = (0.5)2 – 1600=400W.
29. Define all day efficiency of a transformer?
It is computed on the basis of energy consumed during a certain period, usually a day of
24 hrs. All day efficiency=output in kWh/input in kWh tor 24 hrs.
30. List the advantage of stepped core arrangement in a transformer?
1.To reduce the space effectively
2.To obtain reduce length of mean turn of the
winding 3.To reduce I2R loss.
31. Why are breathers used in transformers?
Breathers are used to entrap the atmospheric moisture and thereby not allowing it to
pass on to the transformer oil. Also to permit the oil inside the tank to expand and
contract as its temperature increases and decreases
UNIT-3
1. State the principle of electromechanical energy conversion?
The mechanical energy is converted in to electrical energy which takes place through
either by magnetic field or electric field
2. Distinguish between statically induced emf and dynamically induced emf?
When emf induced in a conductor is stationary in a magnetic field then we call it
statically induced emf.
If emf is induced in a conductor due to relative motion between conductor and the
field then it call it as dynamically induced emf.
3. What does speed voltage mean?
It is that voltage generated in that coil, when there exists a relative motion between
coil and magnetic field
4. Give example for single and multiple excited systems?
Single excited system-reluctance motor, single phase transformer, relay coil
Multiply excited system-alternator, electro mechanical transducer
5. Why do all practical energy conversion devices make use of the magnetic field as a
coupling medium rather than electric field?
When compared to electric field energy can be easily stored and retrieved form a
magnetic system with reduced losses comparatively. Hence most all practical energy
conversion devices make use of magnetic medium as coupling
6. State necessary condition for production of steady torque by the interaction of
stator and rotor field in electric machines?
1.The stator and rotor fields should not have any relative velocity or speed between
each other
2.Airgap between stator and rotor should be minimum
3.Reluctance of iron path should be negligible
4.Mutual flux linkages should exist between stator and rotor windings
7. Write the application of single and doubly fed magnetic systems?
Singly excited systems are employed for motion through a limited distance or rotation
through a prescribed angle
Whereas multiply excited systems are used where continues energy conversion take
place and in ease of transducer where one coil when energized the care of setting up of
flux and the other coil when energized produces a proportional signal either electrical
or mechanical
8. Explain the following with respect to rotating electrical machines
1. Pole pitch
2. Charding angle
1. Pole pitch is that centre to centre distance between any two consecutive poles in a
rotating machine, measured in slots per poles
2. Chording angle is that angle by which the coil span is short of full pitched in
electrical degrees
9. Why energy stored in a magnetic material always occur in air gap
In iron core or steel core the saturation and aging effects form hindrance to storage
Built in air gap as reluctance as well permeability is constant, the energy storage takes
place linearly without any complexity
Hence energy is stored in air gap in a magnetic medium
10. What is the significance of co energy?
When electrical energy is fed to coil not the whole energy is stored as magnetic energy
.the co energy gives a measure of other energy conversion which takes place in coil
then magnetic energy storage
1. Field energy
2. Coenergy
11. Write the equation which relates rotor speed in electrical and mechanical radians
per second?
ὠe=ὠm(p/2)
ὠe=speed in electrical radians per sec ὠm=speed in mechanical radians per sec p=no of
poles
12. Relate co energy density and magnetic flux density?
Co energy density=wf=∫0λ (I, x)
di wf=1/2BH
13. Short advantages of short pitched coil?
1. Hormonics are reduced in induced voltage
2. Saving of copper
3. End connections are shorter
14. What is the significance of winding factor?
Winding factor gives the net reduction in emf induced due to short pitched coil wound
in distributed type
Winding factor kw=kpkd
kp= pitch factor
kd= distribution factor
kp= cos(α/2)
kd= sin(mγ/2)/msin(γ/2)
15. What is the necessity to determine the energy density in the design of rotating
machines?
Energy density wf=B2/2µ
16. Derive the relation between co energy and the phase angle between the rotor and
stator fluxes of the rotating machines?
F1, f2 are the rotor and stator flux peak values
respectively Fr2=f12+f22+2f1f2cosα
Co energy=
{ f12+f22+2f1f2cosα}
17. Write the energy balance equation for motor?
Mechanical energy o/p-=electrical energy i/p-increase in field
energy Ff dx=idλ-dWf
18. Write the expression for the mechanical energy output when the armature moves
from one position to other with constant coil current?
Let us assume armature moves from position xa to xb for a constant coil
current The mechanical energy is
UNIT-4
1. What is prime mover?
The basic source of mechanical power which drives the armature of the generator
is called prime mover.
2. Give the materials used in machine manufacturing?
There are three main materials used in m/c manufacturing they are steel to
conduct magnetic flux copper to conduct electric current insulation.
3. What are factors on which hysteresis loss?
It depends on magnetic flux density, frequency & volume of the material.
4. What is core loss? What is its significance in electric machines?
When a magnetic material undergoes cyclic magnetization, two kinds of power
losses occur on it. Hysteresis and eddy current losses are called as core loss. It is
important in determining heating, temperature rise, rating & efficiency of
transformers, machines & other A.C run magnetic devices.
5. What is eddy current loss?
When a magnetic core carries a time varying flux, voltages are induced in all possible
path enclosing flux. Resulting is the production of circulating flux in core. These
circulating current do no useful work are known as eddy current and have power
loss known as eddy current loss.
5. How hysteresis and eddy current losses are minimized?
Hysteresis loss can be minimized by selecting materials for core such as silicon steel
& steel alloys with low hysteresis co-efficient and electrical resistivity. Eddy current
losses are minimized by laminating the core.
7. How will you find the direction of emf using Fleming’s right hand rule?
The thumb, forefinger & middle finger of right hand are held so that these fingers
are mutually perpendicular to each other, then forefinger-field thumb-motion
middle current.
8. How will you find the direction of force produced using Fleming’s left hand rule?
The thumb, forefinger & middle finger of left hand are held so that these fingers
are mutually perpendicular to each other, then forefinger-field thumb-motion
middle-current.
9. Write down the emf equation for d.c.generator?
E= (ФNZ/60) (P/A)
V. p--->no of poles
Z--->Total noof conductor
Ф--->flux per pole, N--->speed in rpm.
10. Why the armature core in d.c machines is constructed with laminated steel
sheets instead of solid steel sheets?
Lamination highly reduces the eddy current loss and steel sheets provide low
reluctance path to magnetic field.
11. Why commutator is employed in d.c.machines?
Conduct electricity between rotating armature and fixed brushes, convert
alternating emf into unidirectional emf (mechanical rectifier).
12. Distinguish between shunt and series field coil construction?
Shunt field coils are wound with wires of small section and have more no of turns. Series
field coils are wound with wires of larger cross section and have less no of turns.
13. How does D.C. motor differ from D.C. generator in construction?
Generators are normally placed in closed room and accessed by skilled operators
only. Therefore on ventilation point of view they may be constructed with large
opening in the frame. Motors have to be installed right in the place of use which may
have dust, dampness, inflammable gases, chemicals….etc. to protect the motors
against these elements, the motor frames are made either partially closed or totally
closed or flame proof.
14. How will you change the direction of rotation of d.c.motor?
Either the field direction or direction of current through armature conductor is reversed.
15. What is back emf in D.C. motor?
As the motor armature rotates, the system of conductor come across alternate north
and South Pole magnetic fields causing an emf induced in the conductors. The
direction of the emf induced in the conductor is in opposite to current. As this emf
always opposes the flow of current in motor operation it is called as back emf.
16. What is the function of no-voltage release coil in D.C. motor starter?
As long as the supply voltage is on healthy condition the current through the NVR coil
produce enough magnetic force of attraction and retain the starter handle in ON
position against spring force. When the supply voltage fails or becomes lower than a
prescribed value then electromagnet may not have enough force to retain so handle
will come back to OFF position due to spring force automatically.
17. Enumerate the factors on which speed of a d.c.motor depends?
N= (V-IaRa)/Ф so speed depends on air gap flux, resistance of armature,
voltage applied to armature.
18. Under What circumstances does a dc shunt generator fails to generate?
Absence of residual flux, initial flux setup by field may be opposite in direction
to residual flux, shunt field circuit resistance may be higher than its critical field
resistance; load circuit resistance may be less than its critical load resistance.
19. Define critical field resistance of dc shunt generator?
Critical field resistance is defined as the resistance of the field circuit which will
cause the shunt generator just to build up its emf at a specified field.
20. Why is the emf not zero when the field current is reduced to zero in dc generator?
Even after the field current is reduced to zero, the machine is left out with some flux
as residue so emf is available due to residual flux.
21. On what occasion dc generator may not have residual flux?
The generator may be put for its operation after its construction, in previous
operation; the generator would have been fully demagnetized.
22. What are the conditions to be fulfilled by for a dc shunt generator to build
back emf?
The generator should have residual flux, the field winding should be connected in
such a manner that the flux setup by field in same direction as residual flux, the field
resistance should be less than critical field resistance, load circuit resistance should
be above critical resistance.
23 Define armature reaction in dc machines?
The interaction between the main flux and armature flux cause disturbance called
as armature reaction.
24. What are two unwanted effects of armature reactions?
Cross magnetizing effect & demagnetizing effect.
25. What is the function of carbon brush used in dc generators?
The function of the carbon brush is to collect current from commutator and supply
to external load circuit and to load.
26. What are the 2 types of 3phase induction motor?
Squirrel cage and slip ring induction motor.
27. Write two extra features of slip ring induction motor?
Rotor has 3phase winding, Extra resistance can be added in rotor circuit for
improving PF with the help of three slip rings.
28. Why an induction motor is called as rotating transformer?
The rotor receives same electrical power in exactly the same way as the secondary of
a two winding transformer receiving its power from primary. That is why induction
motor is called as rotating transformer.
29. Why an induction motor never runs at its synchronous speed?
If it runs at sy.speed then there would be no relative speed between the two, hence
no rotor emf, so no rotor current, then no rotor torque to maintain rotation.
30. What are slip rings?
The slip rings are made of copper alloys and are fixed around the shaft insulating it.
Through these slip rings and brushes rotor winding can be connected to external circuit.
31. What is the advantage of cage motor?
Since the rotor has low resistance, the copper loss is low and efficiency is very high.
On account of simple construction of rotor it is mechanically robust, initial cost is
less; maintenance cost is less, simple starting arrangement.
32. What are different methods of speed control in D.C shunt motor?
1.Armature control 2.Flux
or field control 3.Applied
voltage control
33. When is a four point DC starter required in DC motors?
A four point DC starter is required for dc motor under field control
34. If speed is decreased in a dc motor, what happens to the back emf decreases and
armature current?
If speed is decreased in a dc motor, the back emf decreases and armature current
increases
35. How does a series motor develop high starting torque?
A dc series motor is always started with some load. Therefore the motor armature
current increases. Due to this, series motor develops high starting torque.
36. What is the necessity of starter in dc motors?
When a dc motor is directly switched on, at the time of starting, the motor back emf is
zero. Due to this, the armature current is very high. Due to the very high current, the
motor gets damaged. To reduce the starting current of the motor a starter is used.
37. Mention the types of braking of dc motor?
1.Regenerative
braking 2.Dynamic
braking 3.Plugging
38. What are the losses in dc motor?
1.Copper losses
2.Iron losses
3.Mechanical losses
39. Name any 2 non-loading method of testing dc machines?
1.Swinburne’s test
2.Hopkinson test
40. Define armature reaction in dc machines?
The interaction between the main flux and armature flux cause disturbance called
as armature reaction.
41. What are two unwanted effects of armature reactions?
Cross magnetizing effect & demagnetizing effect.
42. What is the function of carbon brush used in dc generators?
The function of the carbon brush is to collect current from commutator and supply
to external load circuit and to load.
UNIT-5
1. What is prime mover?
The basic source of mechanical power which drives the armature of the generator is
called prime mover.
What are the essential parts of a d.c generator?
1. Magnetic frame or yoke 2. Poles 3. Armature 4. Commutator, pole shoes, armature
windings, interpoles 5. Brushes, bearings and shaft.
2. Give the materials used in machine manufacturing?
There are three main materials used in m/c manufacturing they are steel to conduct
magnetic flux copper to conduct electric current insulation.
3. What are factors on which hysteresis loss?
It depends on magnetic flux density, frequency & volume of the material.
4. What is core loss? What is its significance in electric machines?
When a magnetic
material undergoes cyclic magnetization, two kinds of power
losses occur on
it. Hysteresis and eddy current losses are called as core loss. It is
important in determining heating, temperature rise, rating & efficiency of
transformers, machines & other A.C run magnetic devices.
5. What is eddy current loss?
When a magnetic core carries a time varying flux, voltages are induced in all possible
path enclosing flux. Resulting is the production of circulating flux in core. These
circulating current do no useful work are known as eddy current and have power loss
known as eddy current loss.
6. How hysteresis and eddy current losses are minimized?
Hysteresis loss can be minimized by selecting materials for core such as silicon steel &
steel alloys with low hysteresis co-efficient and electrical resistivity. Eddy current
losses are minimized by laminating the core.
7. How will you find the direction of emf using Fleming’s right hand rule?
The thumb, forefinger & middle finger of right hand are held so that these fingers are
mutually perpendicular to each other, then forefinger gives the direction of the lines of
flux, thumb gives the direction of the relative motion of conductor and middle finger
gives the direction of the emf induced.
8. How will you find the direction of force produced using Fleming’s left hand rule?
The thumb, forefinger & middle finger of left hand are held so that these fingers
are
mutually perpendicular to each other, then forefinger gives the direction of
magnetic field, middle finger gives the direction of the current and thumb gives the
direction of the force experienced by the conductor.
9. What is the purpose of yoke in d.c machine?
1.It acts as a protecting cover for the whole machine and provides mechanical support
for the poles.
2.It carries magnetic flux produced by the poles
10. What are the types of armature winding?
1.Lap winding, A=P,
2.Wave winding, A=2.
11. How are armatures windings are classified based on placement of coil inside the
armature slots?
Single and double layer winding.
12. Write down the emf equation for d.c.generator?
E= (ФNZ/60)(P/A)V.
p---------no of poles
Z---------Total no of
conductor Ф---------flux per
pole N---------speed in rpm.
13. Why the armature core in d.c machines is constructed with laminated steel
sheets instead of solid steel sheets?
Lamination highly reduces the eddy current loss and steel sheets provide low
reluctance path to magnetic field.
14. Why commutator is employed in d.c.machines?
Conduct electricity between rotating armature and fixed brushes, convert alternating emf
into unidirectional emf (mechanical rectifier).
15. Distinguish between shunt and series field coil construction?
Shunt field coils are wound with wires of small section and have more no of turns. Series
field coils are wound with wires of larger cross section and have less no of turns.
16. How does d.c. motor differ from d.c. generator in construction?
Generators are normally placed in closed room and accessed by skilled operators only.
Therefore on ventilation point of view they may be constructed with large opening in
the frame. Motors have to be installed right in the place of use which may have dust,
dampness, inflammable gases, chemical etc. to protect the motors against these
elements the motor frames are used partially closed or totally closed or flame proof.
17. How will you change the direction of rotation of d.c.motor?
Either the field direction or direction of current through armature conductor is reversed.
18. What is back emf in d.c. motor?
As the motor armature rotates, the system of conductor come across alternate north
and South Pole magnetic fields causing an emf induced in the conductors. The
direction of the emf induced in the conductor is in opposite to current. As this emf
always opposes the flow of current in motor operation it is called as back emf.
19. What is the function of no-voltage release coil in d.c. motor starter?
As long as the supply voltage is on healthy condition the
NVR coil produce enough magnetic force of attraction and
current through the
retain the starter
handle in ON position against spring force. When the supply voltage fails or becomes
lower than a prescribed value then electromagnet may not have enough force to retain
so handle will come back to OFF position due to spring force automatically.
20. Enumerate the factors on which speed of a d.c.motor depends?
N= (V-IaRa)/Ф so speed depends on voltage applied to armature, flux per pole,
resistance of armature.
21. Under what circumstances does a dc shunt generator fails to generate?
Absence of residual flux, initial flux setup by field may be opposite in direction to
residual flux, shunt field circuit resistance may be higher than its critical field
resistance, load circuit resistance may be less than its critical load resistance.
22. Define critical field resistance of dc shunt generator?
Critical field resistance is defined as the resistance of the field circuit which will cause
the shunt generator just to build up its emf at a specified field.
23. Why is the emf not zero when the field current is reduced to zero in dc
generator?
Even after the field current is reduced to zero, the machine is left out with some flux
as residue so emf is available due to residual flux.
24. On what occasion dc generator may not have residual flux?
The generator may be put for its operation after its construction, in previous operation,
the generator would have been fully demagnetized.
25. What are the conditions to be fulfilled by
build back emf?
for a dc shunt generator to
The generator should have residual flux, the field winding should be connected in
such a manner that the flux setup by field in same direction as residual flux, the field
resistance should be less than critical field resistance, load circuit resistance should be
above critical resistance.
26. Define armature reaction in dc machines?
The interaction between the main flux and armature flux cause disturbance called as
armature reaction.
27. What are two unwanted effects of armature reactions?
Cross magnetizing effect & demagnetizing effect.
28. What is the function of carbon brush used in dc generators?
The function of the carbon brush is to collect current from commutator and supply to
external load circuit and to load.
29. What is the principle of generator?
When the armature conductor cuts the magnetic flux emf is induced in the conductor.
30. What is the principle of motor?
When a current carrying conductor is placed in a magnetic field it experiences a force
tending to move it.
Prepared by: T.Ganesh Manickam Lec/EEE
MAHAKAVI BHARATHIYAR COLLEGE OF ENGINEERING AND TECHNOLOGY