Download 6 - Batteries, Bulbs, and Current

Batteries, Bulbs, & Current
July 12
45
Name ________________________ Date ____________ Partners________________________________
BATTERIES, BULBS, & CURRENT
OBJECTIVES
•
•
•
•
•
To understand how a potential difference (voltage) can cause an
electric current through a conductor.
To learn to design and construct simple circuits using batteries,
bulbs, wires, and switches.
To learn to draw circuit diagrams using symbols.
To understand currents at all points in simple circuits.
To understand the meaning of series and parallel connections in an
electric circuit.
OVERVIEW
In the following labs, you are going to discover and extend theories
about electric charge and potential difference (voltage), and apply
them to electric circuits.
A battery is a device that generates an electric potential difference
(voltage) from other forms of energy. The type of batteries you will
use in these labs are known as chemical batteries because they convert
internal chemical energy into electrical energy.
As a result of a potential difference, electric charge is repelled from
one terminal of the battery and attracted to the other. However, no
charge can flow out of a battery unless there is a conducting material
connected between its terminals. If this conductor is the filament in a
small light bulb, the flow of charge will cause the light bulb to glow.
In this lab, you are going to explore how charge flows in wires and
bulbs when energy has been transferred to it by a battery. You will be
asked to develop and explain some models that predict how the charge
flows. You will also be asked to devise ways to test your models using
current and voltage probes which can measure the rate of flow of
University of Virginia Physics Department
PHYS 636, Summer 2006
Modified from P. Laws, D. Sokoloff, R. Thornton
Supported by National Science Foundation
and the U.S. Dept. of Education (FIPSE), 1993-2000
46
Batteries, Bulbs, & Current
July 12
electric charge (current) through a circuit element and the potential
difference (voltage) across a circuit element, respectively, and display
these quantities on a computer screen.
Then you will examine more complicated circuits than a single bulb
connected to a single battery. You will compare the currents through
different parts of these circuits by comparing the brightness of the
bulbs, and also by measuring the currents using current probes.
*Some of the activities in this lab have been adapted from those designed by the
Physics Education Group at the University of Washington.
The following figure shows the parts of the bulb, some of which may
be hidden from view.
Filament
Conducting
metallic
material
Non-conducting
ceramic material
Figure 1-1: Diagram of wiring inside a light bulb.
You will now explore models for current in a simple circuit. In the
diagrams below are shown several models that people often propose.
Model A: There is an electric current
from the top terminal of the battery to
the bulb through wire 1, but no current
back to the base of the battery through
wire 2, since the current is used up
lighting the bulb.
Model B: There is an electric
current in both wires 1 and 2 in a
direction from the battery to the
bulb.
1
1
2
2
Model C: The electric current is in
the direction shown, but there is
less current in the return wire (wire
2), since some of the current is used
up lighting the bulb.
Model D: The electric current is
in the direction shown, and the
magnitude of the current is the same
in both wires 1 and 2.
1
1
2
2
Figure 1-2: Four alternative models for current
University of Virginia Physics Department
PHYS 636, Summer 2006
Modified from P. Laws, D. Sokoloff, R. Thornton
Supported by National Science Foundation
and the U.S. Dept. of Education (FIPSE), 1993-2000
Batteries, Bulbs, & Current
July 12
47
Prediction 1-1: Which model do you think best describes the current
through the bulb? Explain your reasoning.
For the Investigations in this lab, you will need the following:
• two current probes
• two voltage probes
• D cell battery
• 2 resistors (10 Ω)
• push (contact) switch
• knife switch
• 8 wires with alligator clips
• battery holder
• 3 bulbs (#14) and holders
The current probe is a device that measures current and displays it as a
function of time on the computer screen. It will allow you to explore
the current at different locations and under different conditions in your
electric circuits.
To measure the current through a part of the circuit, you must break
open the circuit at the point where you want to measure the current,
and insert the current probe. That is, disconnect the circuit, put in the
current probe, and reconnect with the probe in place.
Note that the current probe measures both the magnitude and direction
of the current. A current in through the “+” terminal and out through
the “-“ terminal (in the direction of the arrow) will be displayed as a
positive current. Thus, if the current measured by the probe is
positive, you know that the current must be counterclockwise in
Figure 1-3 from the “+” terminal of the battery, through the bulb,
through the switch, and toward the “-“ terminal of the battery. On the
other hand, if the probe measures a negative current, then the current
must be clockwise in Figure 1-3 (into the “-“ terminal and out of the
“+” terminal of the probe).
University of Virginia Physics Department
PHYS 636, Summer 2006
Modified from P. Laws, D. Sokoloff, R. Thornton
Supported by National Science Foundation
and the U.S. Dept. of Education (FIPSE), 1993-2000
48
Batteries, Bulbs, & Current
July 12
-
+
+ Current Probe
Interface
Figure 1-3: A circuit with a battery, bulb, switch, and current probe connected to the computer
interface.
Figure 1-4(a) below, shows a simplified diagram representing a
current probe connected as shown in Figure 1-3.
(b)
(a)
CPB
+
CPA
+
+ -
CPA
+ -
Figure 1-4 (a) current probe connected to measure the current out of the + terminal of the battery and
into the bulb; (b) Two current probes, one connected as in (a) and the other connected to measure the
current out of the switch and into the - terminal of the battery.
Look at Figure 1-4(b) and convince yourself that if the currents
measured by current probes CPA and CPB are both positive, this shows
that the current is in a counterclockwise direction around all parts of
the circuit.
INVESTIGATION 1: MODELS DESCRIBING CURRENT
Activity 1-1: Developing a Model for Current in a Circuit
1. Be sure that current probes CPA and CPB are plugged into the
interface.
2. In DataStudio, open the experiment file called Current Model.
Current for two probes versus time should appear on the screen.
University of Virginia Physics Department
PHYS 636, Summer 2006
Modified from P. Laws, D. Sokoloff, R. Thornton
Supported by National Science Foundation
and the U.S. Dept. of Education (FIPSE), 1993-2000
Batteries, Bulbs, & Current
July 12
49
The top axes display the current through CPA and the bottom the
current through CPB. The amount of current through each probe is
also displayed digitally on the screen.
3. To begin, set up the circuit in Figure 1-4(b). Begin graphing, and
try closing the switch for a couple of seconds and then opening it
for a couple of seconds. Repeat this a few times during the time
when you are graphing.
4. Print one set of graphs for your group.
Note: you should observe carefully whether the current through both
probes is essentially the same or if there is a significant difference
(more than a few percent). Write your observation:
Question 1-1: You will notice after closing the switch that the current
through the circuit is not constant in time. This is because the
electrical resistance of a light bulb changes as it heats up, quickly
reaching a steady-state condition. When is the current through the bulb
the largest---just after the switch has been closed, or when the bulb
reaches equilibrium? About how long does it take for the bulb to reach
equilibrium?
Question 1-2: Based on your observations, which of the four models
in Figure 1-2 seems to correctly describe the behavior of the current in
your circuit? Explain based on your observations. Is the current “used
up” by the bulb?
University of Virginia Physics Department
PHYS 636, Summer 2006
Modified from P. Laws, D. Sokoloff, R. Thornton
Supported by National Science Foundation
and the U.S. Dept. of Education (FIPSE), 1993-2000
50
Batteries, Bulbs, & Current
July 12
INVESTIGATION 2: CURRENT AND POTENTIAL DIFFERENCE
+
+
-
-
Battery
Bulb
Switch
Wire
Figure 2-1: Some common circuit symbols
Using these symbols, the circuit with a switch, bulb, wires, and battery
can be sketched as on the right in Figure 2-2.
Figure 2-2: A circuit sketch and corresponding circuit diagram
There are two important quantities to consider in describing the
operation of electric circuits. One is current, which is the flow of
charges (usually electrons) through circuit elements. The other is
potential difference, often referred to as voltage. Let's actually
measure both current and voltage in a familiar circuit.
Figure 2-3 shows the symbols we will use to indicate a current probe
or a voltage probe.
+
+ CP
VP
Figure 2-3 Symbols for current probe and voltage probe.
Figure 2-4(a) shows our simple circuit with voltage probes connected
to measure the voltage across the battery and the voltage across the
bulb. The circuit is drawn again symbolically in Figure 2-4(b). Note
University of Virginia Physics Department
PHYS 636, Summer 2006
Modified from P. Laws, D. Sokoloff, R. Thornton
Supported by National Science Foundation
and the U.S. Dept. of Education (FIPSE), 1993-2000
Batteries, Bulbs, & Current
July 12
51
that the word across is very descriptive of how the voltage probes are
connected.
Activity 2-1: Measuring Potential Difference (Voltage)
1. To set up the voltage probes, first unplug the current probes from
the interface and plug in the voltage probes.
-
-
VPA
+
+
(a)
-
VPA
+
+
VPB
(b)
VPB
Figure 2-4: Two voltage probes connected to measure the voltages across the battery
and the bulb.
2. Open the experiment file called Two Voltages to display graphs
for two voltage probes as a function of time.
3. Connect the circuit shown in Figure 2-4.
Prediction 2-1: In the circuit in Figure 2-4, how would you expect
the voltage across the battery to compare to the voltage across the bulb
with the switch open and closed? Explain.
4. Now test your prediction. Connect the voltage probes to measure
the voltage across the battery and the voltage across the bulb
simultaneously.
5. Click on Start, and close and open the switch a few times.
6. Print one set of graphs for your group.
Question 2-1: Did your observations agree with your Prediction 2-1?
If not, explain.
University of Virginia Physics Department
PHYS 636, Summer 2006
Modified from P. Laws, D. Sokoloff, R. Thornton
Supported by National Science Foundation
and the U.S. Dept. of Education (FIPSE), 1993-2000
52
Batteries, Bulbs, & Current
July 12
Question 2-2: Does the voltage across the battery change as the
switch is opened and closed? What is the "open circuit" battery
voltage, and what is the battery voltage with a "load" on it (i.e. when
it's powering the light bulb)?
Activity 2-2: Measuring Potential Difference (Voltage) and
Current
1. Connect a voltage and a current probe so that you are measuring
the voltage across the battery and the current through the battery at
the same time. (See Figure 2-5.)
2. Open the experiment file called Current and Voltage to display
the current CPB and voltage VPA as a function of time.
-
VPA
CPB
+
VPA
+
CPB
+ -
+ -
Figure 2-5: Probes connected to measure the voltage across the battery and the
current through it.
3. Click on Start, and close and open the switch a few times, as
before.
4. Print one set of graphs for your group.
Question 2-3: Explain the appearance of your current and voltage
graphs. What happens to the current through the battery as the switch
is closed and opened? What happens to the voltage across the battery?
University of Virginia Physics Department
PHYS 636, Summer 2006
Modified from P. Laws, D. Sokoloff, R. Thornton
Supported by National Science Foundation
and the U.S. Dept. of Education (FIPSE), 1993-2000
Batteries, Bulbs, & Current
July 12
53
5. Find the voltage across, and the current through, the battery when
the switch is closed, the bulb is lit, and the values are constant.
Use the Smart Tool and/or the Statistics feature.
Average voltage:__________ Average current: ____________
Prediction 2-2: Now suppose you connect a second bulb in the
circuit, as shown in Figure 2-6. How do you think the voltage across
the battery will compare to that with only one bulb? Will it change
significantly? What about the current in the circuit and the brightness
of the bulbs? Explain.
Comment: These activities assume identical bulbs. Differences in
brightness may arise if the bulbs are not exactly identical. To
determine whether a difference in brightness is caused by a difference
in the currents through the bulbs or by a difference in the bulbs, you
should exchange the bulbs.
Sometimes a bulb will not light noticeably, even if there is a small but
significant current through it. If a bulb is really off, that is, if there is
no current through it, then unscrewing the bulb will not affect the rest
of the circuit. To verify whether a non-glowing bulb actually has a
current through it, unscrew the bulb and see if anything else in the
circuit changes.
6. Connect the circuit with two bulbs, and test your prediction. Take
data. Again measure the voltage across and the current through the
battery with the switch closed.
Average voltage:__________Average current:__________
VPA
VPA
CPB
CPB
Figure 2-6: Two bulbs connected with voltage and current probes.
University of Virginia Physics Department
PHYS 636, Summer 2006
Modified from P. Laws, D. Sokoloff, R. Thornton
Supported by National Science Foundation
and the U.S. Dept. of Education (FIPSE), 1993-2000
54
Batteries, Bulbs, & Current
July 12
Question 2-4: Did the current through the battery change
significantly when you added the second bulb to the circuit (by more
than 5%)?
Question 2-5: Did the voltage across the battery change significantly
when you added the second bulb to the circuit (by more than 5%)?
Question 2-6: Does the battery appear to be a source of constant
current, constant voltage, or neither when different elements are added
to a circuit?
INVESTIGATION 3: CURRENT IN SERIES CIRCUITS
In the next series of activities you will be asked to make a number of
predictions about the current in various circuits, and then to compare
your predictions with actual observations. Whenever your
experimental observations disagree with your predictions you should
try to develop new concepts about how circuits with batteries and
bulbs actually work.
Hint: Helpful symbols are (> "is greater than", < "is less than", = "is
equal to"), for example B>C>A
Prediction 3-1: What would you predict about the relative amount of
current going through each bulb in Figures 3-1 (a) and (b)? Write
down your predicted order of the amount of current passing through
bulbs A, B and C.
Activity 3-1: Current in a Simple Circuit with Bulbs
We continue to see which model in Figure 1-2 accurately represents
what is happening. You can test your Prediction 3-1 by using current
University of Virginia Physics Department
PHYS 636, Summer 2006
Modified from P. Laws, D. Sokoloff, R. Thornton
Supported by National Science Foundation
and the U.S. Dept. of Education (FIPSE), 1993-2000
Batteries, Bulbs, & Current
July 12
55
probes. Convince yourself that the current probes shown in Figure 3-1
measure the currents described in the figure caption.
CPA
CPA
+
-
B
A
CPB
+
-
CPB
+
-
+
-
C
(a)
(b)
Figure 3-1: Current probes connected to measure the current through bulbs. In
circuit (a), CPA measures the current into bulb A, and CPB measures the current out
of bulb A. In circuit (b), CPA measures the current into bulb B while CPB measures
the current out of bulb B and the current into bulb C.
1. Open the experiment file Two Currents to display the two sets of
current axes versus time.
2. Connect circuit (a) in Figure 3-1.
3. Begin graphing, close the switch for a second or so, open it for a
second or so and then close it again.
4. Print one set of graphs for your group.
5. Use the Smart Tool to measure the currents into and out of bulb A
when the switch is closed:
Current into bulb A:______
Current out of bulb A:______
Question 3-1: Are the currents into and out of bulb A equal or is one
significantly larger (do they differ by more than a few percent)? What
can you say about the directions of the currents? Is this what you
expected?
6. Connect circuit (b) in Figure 3-1. Begin graphing current as
above, and record the measured values of the currents.
Current through bulb B:_____Current through bulb C:_____
7. Print one set of graphs for your group.
Question 3-2: Consider your observation of the circuit in Figure 3-1b
with bulbs B and C in it. Is current "used up" in the first bulb or is it
the same in both bulbs?
University of Virginia Physics Department
PHYS 636, Summer 2006
Modified from P. Laws, D. Sokoloff, R. Thornton
Supported by National Science Foundation
and the U.S. Dept. of Education (FIPSE), 1993-2000
56
Batteries, Bulbs, & Current
July 12
Question 3-3: Is the ranking of the currents in bulbs A, B and C what
you predicted? If not, can you explain what assumptions you were
making that now seem false?
Question 3-4: Based on your observations, how is the brightness of a
bulb related to the current through it?
Question 3-5: Formulate a qualitative rule (in words, not an equation)
for predicting whether current increases or decreases as the total
resistance of the circuit is increased.
Comment: The rule you have formulated based on your observations
with bulbs may be qualitatively correct--correctly predicting an
increase or decrease in current--but it won't be quantitatively correct.
That is, it won't allow you to predict the exact sizes of the currents
correctly. This is because the electrical resistance of a bulb changes as
the current through the bulb changes.
Another common circuit element is a resistor. A resistor has a
constant resistance to current regardless of how large the current is
through it (unless it gets quite hot). In the next activity you will
reformulate your rule using resistors.
Prediction 3-2: Consider the circuit diagrams in Figure 3-2 in which
the light bulbs in Figure 3-1 have been replaced by identical resistors.
B
= symbol for a resistor
A
C
a)
b)
Figure 3-2: Two different circuits: (a) a battery with a single resistor, and (b) an
identical battery with two resistors identical to the one in (a).
What would you predict about the relative amount of current going
through each resistor in Figures 3-2 (a) and (b)? Write down your
University of Virginia Physics Department
PHYS 636, Summer 2006
Modified from P. Laws, D. Sokoloff, R. Thornton
Supported by National Science Foundation
and the U.S. Dept. of Education (FIPSE), 1993-2000
Batteries, Bulbs, & Current
July 12
57
predicted rankings of the currents through resistors A, B and C.
(Remember that a resistor has a constant resistance to current
regardless of the current through it.)
Activity 3-2: Current in a Simple Circuit with Resistors
CPA
CPA
B
A
CPB
CPB
C
a)
b)
Figure 3-3: Current probes connected to measure the current through resistors.
In circuit (a), CPA measures the current into resistor A, and CPB measures the
current out of resistor A. In circuit (b), CPA measures the current into resistor B
while CPB measures the current out of resistor B and into resistor C.
1. Continue to use the experiment file Two Currents (but clear the
old data).
2. Connect circuit (a) in Figure 3-3 using the 10 Ω resistor.
3. Use the current probes and the Smart Tool to measure the current
through resistor A in circuit 3-3 (a), then connect circuit 3-3 (b)
and measure the currents through resistors B and C:
Current through resistor A:_________
Current through resistor B:_________
resistor C:_________
Question 3-6: Is the ranking of the currents in resistors A, B and C
what you predicted? If not, can you explain what assumptions you
were making that now seem false?
Question 3-7: How does the amount of current produced by the
battery in the single resistor circuit — Figure 3-3(a) — compare to that
produced by the battery with two resistors connected as in Figure 3-
University of Virginia Physics Department
PHYS 636, Summer 2006
Modified from P. Laws, D. Sokoloff, R. Thornton
Supported by National Science Foundation
and the U.S. Dept. of Education (FIPSE), 1993-2000
58
Batteries, Bulbs, & Current
July 12
3(b)? Does the addition of this second resistor in this manner affect
the current through the original resistor? Explain.
Question 3-8: Re-formulate a more quantitative rule for predicting
how the current supplied by the battery decreases as more resistors are
connected in the circuit as in Figure 3-3(b).
INVESTIGATION 4: CURRENT IN PARALLEL CIRCUITS
There are two basic ways to connect resistors, bulbs or other elements
in a circuit--series and parallel. So far you have been connecting
bulbs and resistors in series. To make predictions involving more
complicated circuits we need to have a more precise definition of
series and parallel. These are summarized in the box below.
i
Series connection:
Two resistors or bulbs are in series if
they are connected so that the same
current that passes through one resistor
or bulb passes through the other. That
is, there is only one path available for
the current.
i
Series
i
junction 1
i2
i1
junction 2
Parallel
Parallel connection:
Two resistors or bulbs are in parallel if
their terminals are connected together such
that at each junction one end of a resistor
or bulb is directly connected to one end of
the other resistor or bulb, e.g., junction 1 in
the diagram.
Similarly, the other ends are connected
together (junction 2).
It is important to keep in mind that in more complex circuits, say with
three or more elements, not every element is necessarily connected in
series or parallel with other elements.
Let's compare the behavior of a circuit with two bulbs wired in parallel
to the circuit with a single bulb. (See Figure 4-1.)
University of Virginia Physics Department
PHYS 636, Summer 2006
Modified from P. Laws, D. Sokoloff, R. Thornton
Supported by National Science Foundation
and the U.S. Dept. of Education (FIPSE), 1993-2000
Batteries, Bulbs, & Current
July 12
59
A
D
E
(b)
(a)
Figure 4-1: Two different circuits: (a) a single bulb circuit and (b) a circuit with two
bulbs identical to the one in (a) connected in parallel to each other and in parallel to
the battery.
Note that if bulbs A, D and E are identical, then the circuit in Figure 42 is equivalent to circuit 4-1(a) when the switch S2 is open (as shown)
and equivalent to circuit 4-1(b) when the switch S2 is closed. Switch
S1 is always closed when taking data and open when not. Switch S1 is
used to prolong the life of the battery.
S2
S1
D
E
Figure 4-2: When the switch S2 is open (S1 is closed), only bulb D is connected to
the battery. When the switch S2 is closed, bulbs D and E are connected in parallel to
each other and in parallel to the battery.
Prediction 4-1: What do you predict about the relative amount of
current through each bulb in a parallel connection, i.e., compare the
current through bulbs D and E in Figure 4-1 (b)?
Prediction 4-2: How do you think that closing the switch S2 in Figure
4-2 affects the current through bulb D (while S1 is closed)?
Activity 4-1: Current in Parallel Branches
You can test Predictions 4-1 and 4-2 by connecting current probes to
measure the currents through bulbs D and E.
University of Virginia Physics Department
PHYS 636, Summer 2006
Modified from P. Laws, D. Sokoloff, R. Thornton
Supported by National Science Foundation
and the U.S. Dept. of Education (FIPSE), 1993-2000
60
Batteries, Bulbs, & Current
July 12
1. Continue to use the experiment file called Two Currents. Clear
the old data.
2. Connect the circuit shown below in Figure 4-3. Add a knife
switch S1 to the left side to save the battery.
S1
S2
CPA
CPB
D
E
Figure 4-3: Current probes connected to measure the current through bulb D and the
current through bulb E.
3. Begin graphing the currents through both probes with S1 closed
then close the switch S2 for a second or so, open it for a second or
so, and then close it again.
4. Print one set of graphs for your group. The knife switch S1 will be
left open to save the battery.
5. Use the Smart Tool to measure both currents.
Switch S2 open:
Current through bulb D:_____Current through bulb E:_____
Switch S2 closed:
Current through bulb D:_____Current through bulb E:_____
Question 4-1: Did closing the switch S2 and connecting bulb E in
parallel with bulb D significantly affect the current through bulb D?
How do you know? (Note: you are making a very significant change
in the circuit. Think about whether the new current through D when
the switch is closed reflects this.)
You have already seen that the voltage maintained by a battery doesn't
change appreciably when changes are made to the circuit (i.e. an ideal
battery is a constant voltage source). But what about the current
through the battery? Is it always the same no matter what is connected
to it, or does it change depending on the circuit? This is what you will
investigate next.
Prediction 4-3: What do you predict about the amount of current
through the battery in the parallel bulb circuit--Figure 4-1 (b)--
University of Virginia Physics Department
PHYS 636, Summer 2006
Modified from P. Laws, D. Sokoloff, R. Thornton
Supported by National Science Foundation
and the U.S. Dept. of Education (FIPSE), 1993-2000
Batteries, Bulbs, & Current
July 12
61
compared to that through the single bulb circuit--Figure 4-1 (a)?
Explain.
Activity 4-2: Current Through the Battery
1. Test your prediction with the circuit shown in Figure 4-4. Use the
same experiment file, Two Currents, as in the previous activities.
Add a switch S1 in the left hand circuit below to save the
battery.
S2
S1
CPB
CPA
D
E
Figure 4-4: Current probes connected to measure the current through the battery and
the current through bulb D.
2. Clear any old data. Begin graphing while closing and opening the
switch S2 as before.
3. Print one set of graphs for your group
4. Label on your graphs when the switch S2 is open and when it is
closed. Remember that switch S1 is always closed when taking
data, but open when not in order to save the battery.
5. Measure the currents through the battery and through bulb D:
Switch S2 open:
Current through battery:_____Current through bulb D:____
Switch S2 closed:
Current through battery:_____Current through bulb D:____
Question 4-2: Does the current through the battery change as you
predicted? If not, why not?
University of Virginia Physics Department
PHYS 636, Summer 2006
Modified from P. Laws, D. Sokoloff, R. Thornton
Supported by National Science Foundation
and the U.S. Dept. of Education (FIPSE), 1993-2000
62
Batteries, Bulbs, & Current
July 12
Question 4-3: Does the addition of more bulbs in parallel increase,
decrease or not change the total resistance of the circuit?
INVESTIGATION 5: MORE COMPLEX SERIES AND PARALLEL CIRCUITS
Now you can apply your knowledge to some more complex circuits.
Consider the circuit consisting of a battery and two bulbs, A and B, in
series shown in Figure 5-1(a). What will happen if you add a third
bulb, C, in parallel with bulb B as shown in Figure 5-1(b)? You
should be able to predict the relative brightness of A, B, and C based
on previous observations. We will address tough questions such as:
How does the brightness of A change when C is connected in parallel
to B?
A
A
B
(a)
B
C
(b)
Figure 5-1: Two circuits with identical components
Question 5-1: In Figure 5-1 (b) is bulb A in series with bulb B? with
bulb C? or with a combination of bulbs B and C? (You may want to
go back to the definitions of series and parallel connections.)
University of Virginia Physics Department
PHYS 636, Summer 2006
Modified from P. Laws, D. Sokoloff, R. Thornton
Supported by National Science Foundation
and the U.S. Dept. of Education (FIPSE), 1993-2000
Batteries, Bulbs, & Current
July 12
63
Question 5-2: In Figure 5-1 (b) are bulbs B and C connected in series
or in parallel with each other, or neither?
Question 5-3: Is the resistance of the combination A, B and C in
Figure 5-1 (b) larger than, smaller than or the same as the combination
of A and B in Figure 5-1 (a)?
Prediction 5-1: Predict how the current through bulb A will change,
if at all, when circuit 5-1 (a) is changed to 5-1 (b) (when bulb C is
added in parallel to bulb B). What will happen to the brightness of
bulb A? Explain the reasons for your predictions.
Prediction 5-2: Predict how the current through bulb B will change,
if at all, when circuit 5-1 (a) is changed to 5-1 (b) (when bulb C is
added in parallel to bulb B). What will happen to the brightness of
bulb B? Explain the reasons for your predictions. (This is difficult to
do without a calculation, but at least explain your considerations.)
Activity 5-1: A More Complex Circuit
1. Set up the circuit shown in Figure 5-2(a). Add a knife switch to
the left side to save the battery. Convince yourself that this
circuit is identical to Figure 5-1 (a) when the switch, S, is open,
and to Figure 5-1 (b) when the switch is closed.
2. Connect the two current probes as shown in Figure 5-2(b). Be
sure you added a switch next to the battery to save the battery.
Open the experiment file Two Currents, if it is not already
opened. Clear any old data.
University of Virginia Physics Department
PHYS 636, Summer 2006
Modified from P. Laws, D. Sokoloff, R. Thornton
Supported by National Science Foundation
and the U.S. Dept. of Education (FIPSE), 1993-2000
64
Batteries, Bulbs, & Current
July 12
CPA
+ -
S1
S1
A
S2
B
C
(a)
A
CPB
B
+
-
S2
C
(b)
Figure 5-2: (a) Circuit equivalent to Figure 5-1 (a) when the switch S2 is open and
to Figure 5-1 (b) when the switch S2 is closed. (b) Same circuit with current probes
connected to measure the current through bulb A (CPA) and the current through bulb
B (CPB). Switch S1 is always closed when taking data.
3. Close the battery switch S1 and begin graphing. Observe what
happens to the current through bulb A (i.e. through the battery) and
the current through bulb B when the switch S2 to bulb C is opened
and closed.
4. Open the battery switch S1.
5. Print one set of graphs for your group.
6. Use the Smart Tool to find the following information:
Without bulb C in the circuit:
current through A:___________ current through B:___________
With bulb C in the circuit:
current through A:___________ current through B:___________
Question 5-4: What happened to the brightness of bulbs A and B as
the switch to bulb C was opened and closed? Compare to your
predictions.
Question 5-5: What happens to the current through the battery when
bulb C is added into the circuit? What do you conclude happens to the
total resistance in the circuit?
University of Virginia Physics Department
PHYS 636, Summer 2006
Modified from P. Laws, D. Sokoloff, R. Thornton
Supported by National Science Foundation
and the U.S. Dept. of Education (FIPSE), 1993-2000