Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Electrification wikipedia , lookup
Thermal runaway wikipedia , lookup
Power engineering wikipedia , lookup
Alternating current wikipedia , lookup
Distributed generation wikipedia , lookup
Wireless power transfer wikipedia , lookup
Life-cycle greenhouse-gas emissions of energy sources wikipedia , lookup
Superconducting RF Cavities for Particle Accelerators: An Introduction Ilan Ben-Zvi Brookhaven National Laboratory In a word: • Superconducting RF (SRF) provides efficient, high-gradient accelerators at high duty-factor. • SRF accelerator cavities are a success story. • Large variety of SRF cavities, depending on: – Type of accelerator – Particle velocity – Current and Duty factor – Gradient – Acceleration or deflecting mode What is a resonant cavity and how do we accelerate beams? • A resonant cavity is the highfrequency analog of a LCR resonant circuit. • RF power at resonance builds up high electric fields used to accelerate charged particles. • Energy is stored in the electric & magnetic fields. Q f f Q Pill-box cavity 2.61a 2 U da 2 J1 (2.405) E02 2 Q=G/Rs G=257 Rs is the surface resistivity. Some important figures of merit • U=PQ/ V2=P·Q·R/Q • A cavity is characterized For a pillbox cavity R/Q=196 by its quality factor Q and the geometric Per cavity: P = V2 · Rs · 1/G · Q/R factors R/Q and G • Dissipated power per Other quantities of interest for a pillbox cavity: cavity depends on Epeak /Eacceleration =1.6 (~2 in elliptical) voltage, surface resistivity and geometry Hpeak /Eacceleration = 30.5 Gauss / MV/m factors. (~40 in elliptical cavities) RF Superconductivity • Superconducting electrons are paired in a coherent quantum state, for DC resistivity disappears bellow the critical field. • In RF, there is the BCS resistivity, arising from the unpaired electrons. For superconducting niobium Rs = RBCS + Rresidul Hc(T)=Hc(0)·[1-(T/Tc)2] For copper = 5.8·107 -1 m-1 so at 1.5 GHz, Rs = 10 m RBCS f Rs 2 10 4 f 17.67 ~ exp T 1.5GHz T 2 and at 1.8K, 1.5 GHz, RBCS = 6 n Rresidual ~ 1 to 10 n Various SRF materials – only one practical and commonly used Material Tc (K) Hc1 (kGauss) H c2(kGauss) Lead 7.7 0.8 0.8 Niobium 9.2 1.7 4 Nb3Sn 18 0.5 300 MgB2 40 0.3 35 “Superheating” field for niobium at 0 K is 2.4 kGauss Design Considerations • Residual resistivity: RactualRBCS+Rresidual • Dependence on field – shape, material, preparation – “Q slope” Electropolishing, baking – Field emission- cleanliness, chemical processing – Thermal conductivity, thermal breakdown – High RRR • Multipacting – cavity shape, cleanliness, processing • Higher Order Modes – loss factor, couplers • Mechanical modes– stiffening, isolation, feedback Measure of performance: The Q vs. accelerating field plot Magnetic fields of 1.7 kGauss (multi-cell) to 1.9 kGauss (single cell) Can be achieved, and recently 2.09 kGauss achieved at Cornell. Limit on fields • Field emission – clean assembly • Magnetic field breakdown (ultimate limit) - good welds, reduce surface fields • Thermal conductivity – high RRR material • Local heating due to defects Fields of 20 to 25 MV/m at Q of over 1010 is routine Choice of material and preparation • High “RRR” material (300 and above) • Large grain material is an old – new approach • Buffered Chemical Polishing (BCP) (HF – HNO3 – H2PO4 , say 1:1:2) • Electropolishing (HF – H2SO4) • UHV baking (~800C) • Low temperature (~120C). • High pressure rinsing • Clean room assembly Multipacting • Multipacting is a resonant, low field conduction in vacuum due to secondary emission • Easily avoided in elliptical cavities with clean surfaces • May show up in couplers! Multipacting in Stanford SCA cavity, 1973 PAC Higher Order Modes (HOM) • Energy is transferred from beam to cavity modes • The power can be very high and must Energy lost by charge q to cavity modes: be dumped safely Longitudinal 2 • Transverse modes U kq and Transverse can cause beam Solution: Strong damping of all HOM, Remove power from all HOM to loads breakup Isolated from liquid helium environment. Electromechanical issues • Lorentz detuning • Pondermotive instabilities • Pressure and acoustic noise Solutions include – broadening resonance curve – feedback control – good mechanical design of cavity and cryostat Miscellaneous hardware • • • • Fundamental mode couplers Pick-up couplers Higher-Order Mode couplers Cryostats (including magnetic shields, thermal shields) • Helium refrigerators (1 watt at 2 K is ~900 watt from plug) • RF power amplifiers (very large for non energy recovered elements Some Examples • • • • • • Low velocity High acceleration gradient Particle deflection High current / Storage rings High current / Energy Recovery Linac RF electron gun Low Resonators Split Loop Resonator Spoke cavity Multi-spoke Quarter Wave Resonator Elliptical Critical applications: Heavy ion accelerators, e.g. RIA High power protons, e.g. SNS, Project-X Radio Frequency Quadrupole High acceleration gradient Critical applications: Linear colliders e.g. ILC X-ray FELs e.g. DESY XFEL Deflecting Cavities Critical applications: Crab crossing (luminosity) e.g. KEK-B, LHC Short X-ray pulses from light sources Energy Recovery Linac: A transform to a boosted frame • Energy needed for acceleration is “borrowed” then returned to cavity. • Little power for field. Energy taken from cavity JLab ERL Demo Energy returned to cavity High current ERL cavities • Multi-ampere current possible in ERL E_2 E_4 E_5 E_6 E_7 E_8 E_9 Critical applications: High average power FELs (e.g. Jlab) High brightness light sources (e.g. Cornell) High luminosity e-P colliders (e.g. eRHIC) E_13 High current SRF photo-injector • Low emittance at high average current is required for FEL. • The high fields (over 20 MV/m) and large acceleration (2 MV) provide good emittance. • High current (0.5 ampere) is possible thanks to 1 MW power delivered to the beam. • Starting point for ERL’s beam. Summary • SRF cavities serve in a large variety of purposes with many shapes. • The future of particle accelerators is in SRF acceleration elements – light sources, colliders, linacs, ERLs and more. • While there is a lot of confidence in the technology, there is still a lot of science to be done.