Download ADA4940-1/ADA4940-2 (Rev. D)

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

History of electric power transmission wikipedia , lookup

Three-phase electric power wikipedia , lookup

Flip-flop (electronics) wikipedia , lookup

Bode plot wikipedia , lookup

Control system wikipedia , lookup

Electrical ballast wikipedia , lookup

Ground loop (electricity) wikipedia , lookup

Signal-flow graph wikipedia , lookup

Immunity-aware programming wikipedia , lookup

Scattering parameters wikipedia , lookup

Power inverter wikipedia , lookup

Negative feedback wikipedia , lookup

Pulse-width modulation wikipedia , lookup

Tube sound wikipedia , lookup

Heterodyne wikipedia , lookup

Islanding wikipedia , lookup

Current source wikipedia , lookup

Power MOSFET wikipedia , lookup

Stray voltage wikipedia , lookup

Regenerative circuit wikipedia , lookup

Variable-frequency drive wikipedia , lookup

Rectifier wikipedia , lookup

Integrating ADC wikipedia , lookup

Amplifier wikipedia , lookup

Alternating current wikipedia , lookup

Wien bridge oscillator wikipedia , lookup

Analog-to-digital converter wikipedia , lookup

Voltage optimisation wikipedia , lookup

Two-port network wikipedia , lookup

Voltage regulator wikipedia , lookup

Power electronics wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Mains electricity wikipedia , lookup

Buck converter wikipedia , lookup

Metadyne wikipedia , lookup

Current mirror wikipedia , lookup

Schmitt trigger wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Opto-isolator wikipedia , lookup

Transcript
Ultralow Power, Low Distortion,
Fully Differential ADC Drivers
ADA4940-1/ADA4940-2
Data Sheet
FEATURES
FUNCTIONAL BLOCK DIAGRAMS
13 –VS
14 –VS
16 –VS
–FB 1
12 DISABLE
+IN 2
11 –OUT
–IN 3
10 +OUT
9
19 –OUT1
21 –VS1
20 DISABLE1
24 +IN1
23 –FB1
22 –VS1
Figure 1. ADA4940-1
18 +OUT1
17 VOCM1
16 –VS2
–IN1 1
+FB1 2
+VS1 3
ADA4940-2
+VS1 4
15 –VS2
NOTES
1. CONNECT THE EXPOSED PAD TO
–VS OR GROUND.
07429-202
+OUT2 12
+VS2 10
13 –OUT2
VOCM2 11
+IN2 6
–IN2 7
14 DISABLE1
+FB2 8
+VS2 9
–FB2 5
GENERAL DESCRIPTION
With the ADA4940-1/ADA4940-2, differential gain configurations
are easily realized with a simple external feedback network of
four resistors determining the closed-loop gain of the amplifier.
The ADA4940-1/ADA4940-2 are fabricated using Analog Devices,
Inc., SiGe complementary bipolar process, enabling them to
achieve very low levels of distortion with an input voltage noise
of only 3.9 nV/√Hz. The low dc offset and excellent dynamic
performance of the ADA4940-1/ADA4940-2 make them well
suited for a variety of data acquisition and signal processing
applications.
08452-001
NOTES
1. CONNECT THE EXPOSED PAD TO
–VS OR GROUND.
Low power PulSAR®/SAR ADC drivers
Single-ended-to-differential conversion
Differential buffers
Line drivers
Medical imaging
Industrial process controls
Portable electronics
The ADA4940-1/ADA4940-2 are low noise, low distortion fully
differential amplifiers with very low power consumption. They
are an ideal choice for driving low power, high resolution, high
performance SAR and Σ-Δ analog-to-digital converters (ADCs)
with resolutions up to 16 bits from dc to 1 MHz on only 1.25 mA
of quiescent current. The adjustable level of the output commonmode voltage allows the ADA4940-1/ADA4940-2 to match the
input common-mode voltage of multiple ADCs. The internal
common-mode feedback loop provides exceptional output balance,
as well as suppression of even-order harmonic distortion products.
VOCM
+VS 8
+VS 7
+VS 6
+VS 5
+FB 4
APPLICATIONS
Rev. D
15 –VS
ADA4940-1
Small signal bandwidth: 260 MHz
Ultralow power 1.25mA
Extremely low harmonic distortion
−122 dB THD at 50 kHz
−96 dB THD at 1 MHz
Low input voltage noise: 3.9 nV/√Hz
0.35 mV maximum offset voltage
Balanced outputs
Settling time to 0.1%: 34 ns
Rail-to-rail output: −VS + 0.1 V to +VS − 0.1 V
Adjustable output common-mode voltage
Flexible power supplies: 3 V to 7 V (LFCSP)
Disable pin to reduce power consumption
ADA4940-1 is available in LFCSP and SOIC packages
Figure 2. ADA4940-2
The ADA4940-1 is available in a 3 mm × 3 mm, 16-lead LFCSP
and an 8-lead SOIC. The ADA4940-2 is available in a 4 mm ×
4 mm, 24-lead LFCSP. The pinouts are optimized to facilitate
printed circuit board (PCB) layout and minimize distortion.
The ADA4940-1/ADA4940-2 are specified to operate over the
−40°C to +125°C temperature range.
Table 1. Similar Products to ADA4940-1/ADA4940-2
Product
AD8137
ADA4932-1
ADA4941-1
ISUPPLY
(mA)
3
9
2.2
Bandwidth
(MHz)
110
560
31
Slew Rate
(V/μs)
450
2800
22
Noise
(nV/√Hz)
8.25
3.6
5.1
Table 2. Complementary Products to ADA4940-1/ADA4940-2
Product
AD7982
AD7984
AD7621
AD7623
Power
(mW)
7.0
10.5
65
45
Throughput
(MSPS)
1
1.333
3
1.333
Resolution
(Bits)
18
18
16
16
SNR
(dB)
98
96.5
88
88
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2011–2016 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADA4940-1/ADA4940-2
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications Information .............................................................. 23
Applications ....................................................................................... 1
Analyzing an Application Circuit ............................................ 23
General Description ......................................................................... 1
Setting the Closed-Loop Gain .................................................. 23
Functional Block Diagrams ............................................................. 1
Estimating the Output Noise Voltage ...................................... 23
Revision History ............................................................................... 3
Impact of Mismatches in the Feedback Networks ................. 24
Specifications..................................................................................... 4
Calculating the Input Impedance of an Application Circuit 24
VS = 5 V.......................................................................................... 4
Input Common-Mode Voltage Range ..................................... 25
VS = 3 V.......................................................................................... 6
Input and Output Capacitive AC Coupling ............................ 26
Absolute Maximum Ratings ............................................................ 8
Setting the Output Common-Mode Voltage .......................... 26
Thermal Resistance ...................................................................... 8
DISABLE Pin .............................................................................. 26
Maximum Power Dissipation ..................................................... 8
Driving a Capacitive Load......................................................... 26
ESD Caution .................................................................................. 8
Driving a High Precision ADC ................................................ 27
Pin Configurations and Function Descriptions ........................... 9
Layout, Grounding, and Bypassing .............................................. 28
Typical Performance Characteristics ........................................... 11
ADA4940-1 LFCSP Example .................................................... 28
Test Circuits ..................................................................................... 20
Outline Dimensions ....................................................................... 29
Terminology .................................................................................... 21
Ordering Guide .......................................................................... 30
Definition of Terms .................................................................... 21
Theory of Operation ...................................................................... 22
Rev. D | Page 2 of 30
Data Sheet
ADA4940-1/ADA4940-2
REVISION HISTORY
5/2016—Rev. C to Rev. D
Changes to Figure 1........................................................................... 1
Deleted Figure 2................................................................................. 1
Added Figure 2; Renumbered Sequentially ................................... 1
Updated Outline Dimensions ........................................................29
Changes to Ordering Guide ...........................................................30
9/2013—Rev. B to Rev. C
Updated Outline Dimensions ........................................................30
Changes to Ordering Guide ...........................................................31
3/2012—Rev. A to Rev. B
Reorganized Layout ........................................................... Universal
Added ADA4940-1 8-Lead SOIC Package ..................... Universal
Changes to Features Section, Table 1, and Figure 1; Replaced
Figure 2 ............................................................................................... 1
Changed VS = ±2 V(or +5 V) Section to VS = +5 V Section ....... 3
Changes to VS = +5 V Section and Table 3 .................................... 3
Changes to Table 4 and Table 5 ....................................................... 4
Changes to VS = 3 V Section and Table 6 ....................................... 5
Changes to Table 7 and Table 8 ....................................................... 6
Added Figure 5 and Table 12, Renumbered Sequentially ............ 9
Changes to Figure 7, Figure 8, and Figure 9 ................................10
Added Figure 15 and Figure 18; Changes to Figure 13,
Figure 14, and Figure 16 .................................................................11
Changes to Figure 19 and Figure 20 .............................................12
Changes to Figure 25, Figure 26, and Figure 27; Added
Figure 28, Figure 29, and Figure 30 ..............................................13
Changes to Figure 31, Figure 32, Figure 33, Figure 34, Figure 35,
and Figure 36 ...................................................................................14
Changes to Figure 37, Figure38, Figure 39, and Figure 41 ........15
Changes to Figure 49, Figure 50, and Figure 51 ..........................17
Added Figure 55 and Figure 57 ..................................................... 18
Changes to Differential VOS, Differential CMRR, and VOCM
CMRR Section ................................................................................. 20
Changes to Calculating the Input Impedance of an Application
Circuit Section ................................................................................. 23
Changes to Figure 71 ...................................................................... 25
Changes to Driving a High Precision ADC Section and
Figure 73 ........................................................................................... 26
Changed ADA4940-1 Example Section to ADA4940-1 LFCSP
Example Section .............................................................................. 27
Changes to Ordering Guide ........................................................... 29
12/2011—Rev. 0 to Rev. A
Changes to Features Section, General Description Section, and
Table 1 ................................................................................................. 1
Replaced Figure 1 and Figure 2 ....................................................... 1
Changes to VS = ±2.5 V (or +5 V) Section and Table 3 ............... 3
Changes to Table 6 ............................................................................ 5
Replaced Figure 7, Figure 8, Figure 9, and Figure 10 ................... 9
Replaced Figure 14, Figure 15, and Figure 17 ............................. 10
Replaced Figure 24 and Figure 27 ................................................. 12
Changes to Figure 37 ...................................................................... 14
Replaced Figure 43 and Figure 46 ................................................. 15
Replaced Figure 53 .......................................................................... 18
Changes to Estimating the Output Noise Voltage Section, Table 14,
Table 15, and Calculating the Input Impedance of an Application
Circuit Section ................................................................................. 21
Changes to Input Common-Mode Voltage Range Section ....... 22
Changes to Driving a High Precision ADC Section and
Figure 65 ........................................................................................... 24
10/2011—Revision 0: Initial Version
Rev. D | Page 3 of 30
ADA4940-1/ADA4940-2
Data Sheet
SPECIFICATIONS
VS = 5 V
VOCM = midsupply, RF = RG = 1 kΩ, RL, dm = 1 kΩ, TA = 25°C, LFCSP package, unless otherwise noted. TMIN to TMAX = −40°C to +125°C.
(See Figure 61 for the definition of terms.)
+DIN or –DIN to VOUT, dm Performance
Table 3.
Parameter
DYNAMIC PERFORMANCE
−3 dB Small Signal Bandwidth
−3 dB Large Signal Bandwidth
Bandwidth for 0.1 dB Flatness
Slew Rate
Settling Time to 0.1%
Overdrive Recovery Time
NOISE/HARMONIC PERFORMANCE
HD2/HD3
IMD3
Input Voltage Noise
Input Current Noise
Crosstalk
INPUT CHARACTERISTICS
Input Offset Voltage
Input Offset Voltage Drift
Input Bias Current
Input Bias Current Drift
Input Offset Current
Input Common-Mode Voltage Range
Input Resistance
Input Capacitance
Common-Mode Rejection Ratio (CMRR)
Open-Loop Gain
OUTPUT CHARACTERISTICS
Output Voltage Swing
Linear Output Current
Output Balance Error
Test Conditions/Comments
Min
Typ
Max
Unit
VOUT, dm = 0.1 V p-p, G = 1
VOUT, dm = 0.1 V p-p, G = 2
VOUT, dm = 0.1 V p-p, G = 5
VOUT, dm = 2 V p-p, G = 1
VOUT, dm = 2 V p-p, G = 2
VOUT, dm = 2 V p-p, G = 5
VOUT, dm = 2 V p-p, G = 1 and G = 2
VOUT, dm = 2 V step
VOUT, dm = 2 V step
G = 2, VIN, dm = 6 V p-p, triangle wave
260
220
75
25
22
19
14.5
95
34
86
MHz
MHz
MHz
MHz
MHz
MHz
MHz
V/µs
ns
ns
VOUT, dm = 2 V p-p, fC = 10 kHz
VOUT, dm = 2 V p-p, fC = 50 kHz
VOUT, dm = 2 V p-p, fC = 50 kHz, G = 2
VOUT, dm = 2 V p-p, fC = 1 MHz
VOUT, dm = 2 V p-p, fC = 1 MHz, G = 2
VOUT, dm = 2 V p-p, f1 = 1.9 MHz, f2 = 2.1 MHz
f = 100 kHz
f = 100 kHz
VOUT, dm = 2 V p-p, fC = 1 MHz
−125/−118
−123/−126
−124/−117
−102/−96
−100/–92
−99
3.9
0.81
−110
dBc
dBc
dBc
dBc
dBc
dBc
nV/√Hz
pA/√Hz
dB
VIP = VIN = VOCM = 0 V
TMIN to TMAX
−0.35
−1.6
TMIN to TMAX
−500
Differential
Common mode
ΔVOS, dm/ΔVIN, cm, ∆VIN, cm = ±1 V dc
86
91
Each single-ended output
−VS + 0.1 to
+VS − 0.1
f = 1 MHz, RL, dm = 22 Ω, SFDR = −60 dBc
f = 1 MHz, ΔVOUT, cm/ΔVOUT, dm
Rev. D | Page 4 of 30
±0.06
1.2
−1.1
−4.5
±50
−VS − 0.2 to
+VS − 1.2
33
50
1
119
99
−VS + 0.07 to
+VS − 0.07
46
−65
+0.35
+500
mV
µV/°C
µA
nA/°C
nA
V
kΩ
MΩ
pF
dB
dB
V
−60
mA peak
dB
Data Sheet
ADA4940-1/ADA4940-2
VOCM to VOUT, cm Performance
Table 4.
Parameter
VOCM DYNAMIC PERFORMANCE
−3 dB Small Signal Bandwidth
−3 dB Large Signal Bandwidth
Slew Rate
Input Voltage Noise
Gain
VOCM CHARACTERISTICS
Input Common-Mode Voltage Range
Input Resistance
Offset Voltage
Input Offset Voltage Drift
Input Bias Current
CMRR
Test Conditions/Comments
VOUT, cm = 0.1 V p-p
VOUT, cm = 1 V p-p
VOUT, cm = 1 V p-p
f = 100 kHz
ΔVOUT, cm/ΔVOCM, ΔVOCM = ±1 V
Min
Typ
0.99
36
29
52
83
1
ΔVOS, dm/ΔVOCM, ΔVOCM = ±1 V
−7
86
−VS + 0.8 to
+VS − 0.7
250
±1
20
+4
100
Test Conditions/Comments
Min
Typ
LFCSP
SOIC
Enabled
TMIN to TMAX
Disabled
ΔVOS, dm/ΔVS, ΔVS = 1 V p-p
ΔVOS, dm/ΔVS, ΔVS = 1 V p-p
3
3
1.05
VOS, cm = VOUT, cm − VOCM; VIP = VIN = VOCM = 0 V
TMIN to TMAX
−6
Max
Unit
1.01
MHz
MHz
V/µs
nV/√Hz
V/V
V
kΩ
mV
µV/°C
µA
dB
+6
Max
Unit
7
6
1.38
V
V
mA
µA/°C
µA
dB
dB
+7
General Performance
Table 5.
Parameter
POWER SUPPLY
Operating Range
Quiescent Current per Amplifier
Quiescent Current Drift
+PSRR
−PSRR
DISABLE (DISABLE PIN)
DISABLE Input Voltage
Turn-Off Time
Turn-On Time
DISABLE Pin Bias Current per Amplifier
Enabled
Disabled
80
80
Disabled
Enabled
1.25
4.25
13.5
90
96
28.5
≤(−VS + 1)
≥(−VS + 1.8)
10
0.6
DISABLE = +2.5 V
DISABLE = −2.5 V
OPERATING TEMPERATURE RANGE
−10
−40
Rev. D | Page 5 of 30
2
−5
V
V
µs
µs
5
µA
µA
+125
°C
ADA4940-1/ADA4940-2
Data Sheet
VS = 3 V
VOCM = midsupply, RF = RG = 1 kΩ, RL, dm = 1 kΩ, TA = 25°C, LFCSP package, unless otherwise noted. TMIN to TMAX = −40°C to +125°C.
(See Figure 61 for the definition of terms.)
+DIN or –DIN to VOUT, dm Performance
Table 6.
Parameter
DYNAMIC PERFORMANCE
−3 dB Small Signal Bandwidth
−3 dB Large Signal Bandwidth
Bandwidth for 0.1 dB Flatness
Slew Rate
Settling Time to 0.1%
Overdrive Recovery Time
NOISE/HARMONIC PERFORMANCE
HD2/HD3
IMD3
Input Voltage Noise
Input Current Noise
Crosstalk
INPUT CHARACTERISTICS
Input Offset Voltage
Input Offset Voltage Drift
Input Bias Current
Input Bias Current Drift
Input Offset Current
Input Common-Mode Voltage Range
Input Resistance
Input Capacitance
Common-Mode Rejection Ratio (CMRR)
Open-Loop Gain
OUTPUT CHARACTERISTICS
Output Voltage Swing
Linear Output Current
Output Balance Error
Test Conditions/Comments
Min
Typ
Max
Unit
VOUT, dm = 0.1 V p-p
VOUT, dm = 0.1 V p-p, G = 2
VOUT, dm = 0.1 V p-p, G = 5
VOUT, dm = 2 V p-p
VOUT, dm = 2 V p-p, G = 2
VOUT, dm = 2 V p-p, G = 5
VOUT, dm = 0.1 V p-p
VOUT, dm = 2 V step
VOUT, dm = 2 V step
G = 2, VIN, dm = 3.6 V p-p, triangle wave
240
200
70
24
20
17
14
90
37
85
MHz
MHz
MHz
MHz
MHz
MHz
MHz
V/µs
ns
ns
VOUT, dm = 2 V p-p, fC = 50 kHz (HD2/HD3)
VOUT, dm = 2 V p-p, fC = 1 MHz (HD2/HD3)
VOUT, dm = 2 V p-p, f1 = 1.9 MHz, f2 = 2.1 MHz
f = 100 kHz
f = 100 kHz
VOUT, dm = 2 V p-p, fC = 1 MHz
−115/−121
−104/−96
−98
3.9
0.84
−110
dBc
dBc
dBc
nV/√Hz
pA/√Hz
dB
VIP = VIN = VOCM = 1.5 V
TMIN to TMAX
−0.4
−1.6
TMIN to TMAX
−500
Differential
Common mode
ΔVOS, dm/ΔVIN, cm, ∆VIN, cm = ±0.25 V dc
86
91
Each single-ended output
−VS + 0.08 to
+VS − 0.08
f = 1 MHz, RL, dm = 26 Ω, SFDR = −60 dBc
f = 1 MHz, ΔVOUT, cm/ΔVOUT, dm
Rev. D | Page 6 of 30
±0.06
1.2
−1.1
−4.5
±50
−VS − 0.2 to
+VS − 1.2
33
50
1
114
99
−VS + 0.04 to
+VS − 0.04
38
−65
+0.4
+500
mV
µV/°C
µA
nA/°C
nA
V
kΩ
MΩ
pF
dB
dB
V
−60
mA peak
dB
Data Sheet
ADA4940-1/ADA4940-2
VOCM to VOUT, cm Performance
Table 7.
Parameter
VOCM DYNAMIC PERFORMANCE
−3 dB Small Signal Bandwidth
−3 dB Large Signal Bandwidth
Slew Rate
Input Voltage Noise
Gain
VOCM CHARACTERISTICS
Input Common-Mode Voltage Range
Input Resistance
Offset Voltage
Input Offset Voltage Drift
Input Bias Current
CMRR
Test Conditions/Comments
VOUT, cm = 0.1 V p-p
VOUT, cm = 1 V p-p
VOUT, cm = 1 V p-p
f = 100 kHz
ΔVOUT, cm/ΔVOCM, ΔVOCM = ±0.25 V
Min
Typ
0.99
36
26
48
92
1
ΔVOS,dm/ΔVOCM, ΔVOCM = ±0.25 V
−5
80
−VS + 0.8 to
+VS − 0.7
250
±1
20
+1
100
Test Conditions/Comments
Min
Typ
LFCSP
SOIC
Enabled
TMIN to TMAX
Disabled
ΔVOS, dm/ΔVS, ΔVS = 0.25 V p-p
ΔVOS, dm/ΔVS, ΔVS = 0.25 V p-p
3
3
1
VOS, cm = VOUT, cm − VOCM; VIP = VIN = VOCM = 1.5 V
TMIN to TMAX
−7
Max
Unit
1.01
MHz
MHz
V/µs
nV/√Hz
V/V
V
kΩ
mV
µV/°C
µA
dB
+7
Max
Unit
7
6
1.33
V
V
mA
µA/°C
µA
dB
dB
+5
General Performance
Table 8.
Parameter
POWER SUPPLY
Operating Range
Quiescent Current per Amplifier
+PSRR
−PSRR
DISABLE (DISABLE PIN)
DISABLE Input Voltage
Turn-Off Time
Turn-On Time
DISABLE Pin Bias Current per Amplifier
Enabled
Disabled
80
80
1.18
4.25
7
90
96
Disabled
Enabled
≤(−VS + 1)
≥(−VS + 1.8)
16
0.6
DISABLE = +3 V
DISABLE = 0 V
0.3
−3
−6
OPERATING TEMPERATURE RANGE
−40
Rev. D | Page 7 of 30
22
V
V
µs
µs
1
µA
µA
+125
°C
ADA4940-1/ADA4940-2
Data Sheet
ABSOLUTE MAXIMUM RATINGS
Table 9.
Parameter
Supply Voltage
VOCM
Differential Input Voltage
Operating Temperature Range
Storage Temperature Range
Lead Temperature (Soldering, 10 sec)
Junction Temperature
ESD
Field Induced Charged Device Model (FICDM)
Human Body Model (HBM)
Rating
8V
±VS
1.2 V
−40°C to +125°C
−65°C to +150°C
300°C
150°C
1250 V
2000 V
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
The power dissipated in the package (PD) is the sum of the
quiescent power dissipation and the power dissipated in the
package due to the load drive for all outputs. The quiescent
power dissipation is the voltage between the supply pins (±VS)
times the quiescent current (IS). The load current consists of the
differential and common-mode currents flowing to the load, as
well as currents flowing through the external feedback networks
and internal common-mode feedback loop. The internal
resistor tap used in the common-mode feedback loop places a
negligible differential load on the output. Consider rms voltages
and currents when dealing with ac signals.
Airflow reduces θJA. In addition, more metal directly in contact
with the package leads from metal traces, through holes, ground,
and power planes reduces the θJA.
Figure 3 shows the maximum safe power dissipation in the
package vs. the ambient temperature for the 8-lead SOIC (θJA =
158°C/W, single) the 16-lead LFCSP (θJA = 91.3°C/W, single)
and 24-lead LFCSP (θJA = 65.1°C/W, dual) packages on a JEDEC
standard 4-layer board. θJA values are approximations.
3.5
THERMAL RESISTANCE
Package Type
8-Lead SOIC (Single)/4-Layer Board
16-Lead LFCSP (Single)/4-Layer Board
24-Lead LFCSP (Dual)/4-Layer Board
θJA
158
91.3
65.1
Unit
°C/W
°C/W
°C/W
MAXIMUM POWER DISSIPATION
The maximum safe power dissipation in the ADA4940-1/
ADA4940-2 packages is limited by the associated rise in
junction temperature (TJ) on the die. At approximately 150°C,
which is the glass transition temperature, the plastic changes its
properties. Even temporarily exceeding this temperature limit
can change the stresses that the package exerts on the die,
permanently shifting the parametric performance of the
ADA4940-1/ADA4940-2. Exceeding a junction temperature
of 150°C for an extended period can result in changes in the
silicon devices, potentially causing failure.
ADA4940-2 (LFCSP)
2.5
ADA4940-1 (LFCSP)
2.0
1.5
1.0
0.5
0
–40
ADA4940-1 (SOIC)
–20
0
20
40
60
80
100
120
AMBIENT TEMPERATURE (°C)
Figure 3. Maximum Safe Power Dissipation vs. Ambient Temperature
ESD CAUTION
Rev. D | Page 8 of 30
08452-004
Table 10.
3.0
MAXIMUM POWER DISSIPATION (W)
θJA is specified for the worst-case conditions, that is, θJA is
specified for the device soldered on a circuit board in still air.
Data Sheet
ADA4940-1/ADA4940-2
13 –VS
–FB 1
12 DISABLE
+IN 2
11 –OUT
–IN 3
10 +OUT
NOTES
1. CONNECT THE EXPOSED PAD TO
–VS OR GROUND.
2
3
4
+IN
−IN
+FB
5 to 8
9
10
+VS
VOCM
+OUT
11
−OUT
12
13 to 16
DISABLE
−VS
Exposed
pad (EPAD)
DISABLE
+VS 3
6
–VS
+OUT 4
5
–OUT
ADA4940-1
Figure 5. ADA4940-1 Pin Configuration (8-Lead SOIC)
Table 11. ADA4940-1 Pin Function Descriptions (16-Lead
LFCSP)
Mnemonic
−FB
+IN
7
VOCM
Figure 4. ADA4940-1 Pin Configuration (16-Lead LFCSP)
Pin No.
1
8
+VS 8
+VS 7
+VS 6
9
+VS 5
+FB 4
–IN 1
VOCM 2
08452-101
14 –VS
16 –VS
15 –VS
ADA4940-1
PIN 1
INDICATOR
08452-003
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
Description
Negative Output for Feedback
Component Connection.
Positive Input Summing Node.
Negative Input Summing Node.
Positive Output for Feedback
Component Connection.
Positive Supply Voltage.
Output Common-Mode Voltage.
Positive Output for Load
Connection.
Negative Output for Load
Connection.
Disable Pin.
Negative Supply Voltage.
Connect the exposed pad to −VS or
ground.
Table 12. ADA4940-1 Pin Function Descriptions (8-Lead
SOIC)
Pin No.
1
2
3
4
Mnemonic
−IN
VOCM
+VS
+OUT
5
−OUT
6
7
8
−VS
DISABLE
+IN
Rev. D | Page 9 of 30
Description
Negative Input Summing Node
Output Common-Mode Voltage
Positive Supply Voltage
Positive Output for Load
Connection
Negative Output for Load
Connection
Negative Supply Voltage
Disable Pin
Positive Input Summing Node
20 DISABLE1
19 –OUT1
21 –VS1
Data Sheet
24 +IN1
23 –FB1
22 –VS1
ADA4940-1/ADA4940-2
18 +OUT1
17 VOCM1
16 –VS2
–IN1 1
+FB1 2
+VS1 3
ADA4940-2
+VS1 4
15 –VS2
–FB2 5
14 DISABLE1
+IN2 6
NOTES
1. CONNECT THE EXPOSED PAD TO
–VS OR GROUND.
08452-102
+OUT2 12
+VS2 10
VOCM2 11
–IN2 7
+FB2 8
+VS2 9
13 –OUT2
Figure 6. ADA4940-2 Pin Configuration (24-Lead LFCSP)
Table 13. ADA4940-2 Pin Function Descriptions (24-Lead LFCSP)
Pin No.
1
2
3, 4
5
6
7
8
9, 10
11
12
13
14
15, 16
17
18
19
20
21, 22
23
24
Mnemonic
−IN1
+FB1
+VS1
−FB2
+IN2
−IN2
+FB2
+VS2
VOCM2
+OUT2
−OUT2
DISABLE2
−VS2
VOCM1
+OUT1
−OUT1
DISABLE1
−VS1
−FB1
+IN1
Exposed pad (EPAD)
Description
Negative Input Summing Node 1.
Positive Output Feedback Pin 1.
Positive Supply Voltage 1.
Negative Output Feedback Pin 2.
Positive Input Summing Node 2.
Negative Input Summing Node 2.
Positive Output Feedback Pin 2.
Positive Supply Voltage 2.
Output Common-Mode Voltage 2.
Positive Output 2.
Negative Output 2.
Disable Pin 2.
Negative Supply Voltage 2.
Output Common-Mode Voltage 1.
Positive Output 1.
Negative Output 1.
Disable Pin 1.
Negative Supply Voltage 1.
Negative Output Feedback Pin 1.
Positive Input Summing Node 1.
Connect the exposed pad to −VS or ground.
Rev. D | Page 10 of 30
Data Sheet
ADA4940-1/ADA4940-2
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C, VS = ±2.5 V, G = 1, RF = RG = 1 kΩ, RT = 52.3 Ω (when used), RL = 1 kΩ, unless otherwise noted. See Figure 59 and Figure 60 for the
test circuits.
3
3
G = 1, RL = 1kΩ
2
2
1
–1
G = 1, RL = 200Ω
–2
–3
G = 2, RL = 1kΩ
–4
–5
G = 2, RL = 200Ω
–6
–8
10
100
–4
G = 2, RL = 200Ω
–5
–6
G = 1, RL = 200Ω
1000
Figure 7. Small Signal Frequency Response for Various Gains and Loads
(LFCSP)
3
VOUT = 2V p-p
–9
0.1
1
08452-006
1
FREQUENCY (MHz)
G = 1, RL = 1kΩ
10
100
1000
FREQUENCY (MHz)
Figure 10. Large Signal Frequency Response for Various Gains and Loads
3
VS = ±3.5V
2
2
1
1
0
0
VS = ±2.5V
–1
VS = ±3.5V
VS = ±1.5V
–3
–4
–3
–5
–6
–6
–7
–7
–8
–8
10
100
1000
FREQUENCY (MHz)
VS = ±1.5V
–4
–5
VOUT, dm = 0.1V p-p
–9
0.1
1
VS = ±2.5V
–2
VOUT = 2V p-p
–9
0.1
1
10
100
1000
FREQUENCY (MHz)
Figure 8. Small Signal Frequency Response for Various Supplies (LFCSP)
08452-010
GAIN (dB)
–1
–2
08452-007
Figure 11. Large Signal Frequency Response for Various Supplies
3
3
2
2
–40°C
1
1
0
0
–1
–1
–3
GAIN (dB)
+25°C
–2
+125°C
–4
+125°C
–3
–4
–5
–6
–6
–7
–7
–8
VOUT, dm = 0.1V p-p
10
100
FREQUENCY (MHz)
1000
–9
08452-008
1
+25°C
–2
–5
–8
–40°C
Figure 9. Small Signal Frequency Response for Various Temperatures (LFCSP)
VOUT, dm = 2V p-p
1
10
100
FREQUENCY (MHz)
1000
08452-011
GAIN (dB)
–3
–8
VOUT, dm = 0.1V p-p
–9
0.1
GAIN (dB)
–2
–7
–7
–9
G = 2, RL = 1kΩ
0
–1
08452-009
0
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
1
Figure 12. Large Signal Frequency Response for Various Temperatures
Rev. D | Page 11 of 30
ADA4940-1/ADA4940-2
Data Sheet
4
3
3
SOIC-1
LFCSP-1
2
1
1
0
–1
LFCSP-2: CH2
–1
–2
GAIN (dB)
LFCSP-2:CH1
–3
–4
–7
–8
VOUT, dm = 0.1V p-p
10
100
1000
FREQUENCY (MHz)
08452-012
1
–9
100
1000
Figure 16. Large Signal Frequency Response for Various Packages
3
3
2
VOCM = –1V
VOCM = 0V
VOCM = +1V
2
VOCM = 0V
1
1
0
0
VOCM = –1V
–2
–1
GAIN (dB)
–1
VOCM = +1V
–3
–4
–2
–3
–4
–5
–5
–6
–6
–7
–8
VOUT, dm = 0.1V p-p
10
100
1000
FREQUENCY (MHz)
08452-013
1
3
1
10
100
1000
FREQUENCY (MHz)
Figure 14. Small Signal Frequency Response at Various VOCM Levels (LFCSP)
4
VOUT, dm = 2V p-p
–9
0.1
08452-016
–7
–9
0.1
10
FREQUENCY (MHz)
Figure 13. Small Signal Frequency Response for Various Packages
–8
VOUT = 2V p-p
1
08452-015
–7
GAIN (dB)
–4
–6
–6
Figure 17. Large Signal Frequency Response at Various VOCM Levels
4
VOCM = 0V
3
2
2
1
1
0
SOIC: RL = 1kΩ
SOIC: RL = 200Ω
0
–2
GAIN (dB)
VOCM = –1V
–1
VOCM = +1V
–3
–4
–1
–2
–3
–5
–6
–6
–7
–7
–8 V
OUT, dm = 0.1V p-p
–9
0.1
1
–8 V
OUT, dm = 0.1V p-p
–9
0.1
1
10
100
1000
FREQUENCY (MHz)
Figure 15. Small Signal Frequency Response for Various VOCM (SOIC)
LFCSP: RL = 1kΩ
LFCSP: RL = 200Ω
–4
–5
08452-205
GAIN (dB)
–3
–5
–5
–9
0.1
–2
10
FREQUENCY (MHz)
100
1000
08452-203
GAIN (dB)
0
–8
LFCSP-1
LFCSP-2: CH1
LFCSP-2: CH2
SOIC-1
2
Figure 18. Small Signal Frequency Response for Various Packages and Loads
Rev. D | Page 12 of 30
Data Sheet
ADA4940-1/ADA4940-2
4
4
CCOM1 = CCOM2 = 2pF
3
2
2
1
1
CCOM1 = CCOM2 = 1pF
–2
CCOM1 = CCOM2 = 0.5pF
–3
CCOM1 = CCOM2 = 0pF
GAIN (dB)
0
–1
–4
–3
–4
–5
–6
–7
–7
100
1000
Figure 19. Small Signal Frequency Response for Various Capacitive Loads
(LFCSP)
0.20
0.15
0.15
NORMALIZED GAIN (dB)
0.25
0
–0.05
G = 2, RL = 200Ω
–0.10
G = 2, RL = 1kΩ
–0.15
1
G = 1, RL = 1kΩ
0
–0.05
G = 2, RL = 200Ω
–0.10
G = 2, RL = 1kΩ
G = 1, RL = 200Ω
10
100
1000
FREQUENCY (MHz)
VOUT, dm = 2V p-p
–0.25
0.1
08452-018
–0.25
0.1
0.05
–0.20
G = 1, RL = 1kΩ
VOUT, dm = 0.1V p-p
1000
0.10
–0.15
G = 1, RL = 200Ω
–0.20
100
Figure 22. Large Signal Frequency Response for Various Capacitive Loads
0.20
0.05
10
FREQUENCY (MHz)
0.25
0.10
1
1
10
100
1000
FREQUENCY (MHz)
Figure 20. 0.1 dB Flatness Small Signal Frequency Response for
Various Gains and Loads (LFCSP)
08452-021
10
–9
08452-017
–8 CDIFF = 0pF
VOUT = 2V p-p
FREQUENCY (MHz)
Figure 23. 0.1 dB Flatness Large Signal Frequency Response for
Various Gains and Loads
3
3
2
2
1
1
0
0
–1
GAIN (dB)
–2
VS = ±1.5V
–3
–4
–2
–3
–5
–6
–6
–7
–7
–8
VOUT, dm = 0.1V p-p
10
100
FREQUENCY (MHz)
1000
–9
08452-019
1
VS = ±1.5V
–4
–5
–8
VS = ±2.5V
–1
VS = ±2.5V
Figure 21. VOCM Small Signal Frequency Response for Various Supplies
VOUT, dm = 1V p-p
1
10
100
FREQUENCY (MHz)
1000
08452-022
NORMALIZED GAIN (dB)
–2
–6
–8 CDIFF = 0pF
VOUT = 0.1V p-p
–9
1
GAIN (dB)
–1
–5
08452-014
GAIN (dB)
0
–9
CCOM1 = CCOM2 = 0pF
CCOM1 = CCOM2 = 0.5pF
CCOM1 = CCOM2 = 1pF
CCOM1 = CCOM2 = 2pF
3
Figure 24. VOCM Large Signal Frequency Response for Various Supplies
Rev. D | Page 13 of 30
ADA4940-1/ADA4940-2
Data Sheet
–20
–20
VOUT, dm = 2V p-p
–30
–40
HARMONIC DISTORTION (dBc)
–50
–60
HD3, G = 2
–70
HD3, G = 1
–80
HD2, G = 2
–90
HD2, G = 1
–100
–110
–120
–70
–80
HD2, G = 2
–90
HD2, G = 1
–100
–110
–20
–30
HARMONIC DISTORTION (dBc)
–40
–50
–60
HD3, RL = 200Ω
–70
HD3, RL = 1kΩ
–80
–90
–100
HD2, RL = 1kΩ
HD2, RL = 200Ω
–110
1
0.1
10
Figure 28. Harmonic Distortion vs. Frequency vs. Gain (SOIC)
VOUT, dm = 2V p-p
–30
–120
VOUT, dm = 2V p-p
–40
–50
HD3, RL = 200Ω
–60
–70
–80
HD2, RL = 200Ω
–90
HD2, RL = 1kΩ
–100
–110
–120
1
0.1
10
FREQUENCY (MHz)
Figure 26. Harmonic Distortion vs. Frequency for Various Loads (LFCSP)
–20
–40
–40
HARMONIC DISTORTION (dBc)
–30
–70
–80
HD2, VS = ±3.5V
–90
HD3, VS = ±1.5V
HD2, VS = ±1.5V
HD3, VS = ±3.5V
HD2, VS = ±2.5V
VOUT, dm = 2V p-p
–50
–60
–70
–80
–90
–100
–110
HD2, ±1.5V
HD2, ±2.5V
–120
–120
HD3, VS = ±2.5V
0.1
1
FREQUENCY (MHz)
10
HD3, ±1.5V
–130
0.01
08452-024
–130
0.01
10
Figure 29. Harmonic Distortion vs. Frequency for Various Loads (SOIC)
VOUT, dm = 2V p-p
–60
1
0.1
FREQUENCY (MHz)
–30
–50
HD3, RL = 1kΩ
–130
0.01
08452-020
–130
0.01
08452-201
HARMONIC DISTORTION (dBc)
–60
FREQUENCY (MHz)
–20
HARMONIC DISTORTION (dBc)
–50
–130
0.01
Figure 25. Harmonic Distortion vs. Frequency for Various Gains (LFCSP)
–110
HD3, G = 1
08452-200
10
08452-023
1
0.1
FREQUENCY (MHz)
–100
HD3, G = 2
–40
–120
–130
0.01
–20
VOUT, dm = 2V p-p
HD3, ±2.5V
0.1
1
FREQUENCY (MHz)
Figure 27. Harmonic Distortion vs. Frequency for Various Supplies (LFCSP)
10
08452-202
HARMONIC DISTORTION (dBc)
–30
Figure 30. Harmonic Distortion vs. Frequency for Various Supplies (SOIC)
Rev. D | Page 14 of 30
Data Sheet
ADA4940-1/ADA4940-2
HARMONIC DISTORTION (dBc)
–50
–60
–70
SOIC: RL = 200Ω
–90
SOIC: RL = 1kΩ
–100
–110
LFCSP: RL = 1kΩ
–120
1
VS = +3V, 0V HD3
–70
VS = +3V, 0V HD2
–80
10
Figure 31. Spurious-Free Dynamic Range vs. Frequency at
RL = 200 Ω and RL = 1 kΩ
–100
VS = ±3.5V HD3
–110
VS = ±2.5V HD3
–140
0
–20
4
5
6
7
8
9
10
HARMONIC DISTORTION (dBc)
–40
–50
–60
–70
HD3 AT 1MHz
HD2 AT 1MHz
–90
–100
–110
–120
–50
–60
–70
–80
HD2 AT 1MHz
–90
HD3 AT 1MHz
–100
–110
–120
–130
HD2 AT 100kHz
–2.0
–1.5
–1.0
–0.5
0
–130
HD3 AT 100kHz
0.5
1.0
1.5
2.0
2.5
VOCM (V)
–140
08452-025
–140
HD2 AT 100kHz
HD3 AT 100kHz
Figure 32. Harmonic Distortion vs. VOCM for 100 kHz and 1 MHz,
±2.5 V Supplies (LFCSP)
0
0.5
1.0
1.5
2.0
2.5
3.0
VOCM (V)
08452-028
–80
Figure 35. Harmonic Distortion vs. VOCM for 100 kHz and 1 MHz, 3 V Supply
(LFCSP)
–20
–20
HD3 AT VOUT, dm = 8V p-p
–30
–40
HD2 AT VOUT, dm = 8V p-p
–40
–50
HD3 AT VOUT, dm = 4V p-p
HARMONIC DISTORTION (dBc)
–30
HD2 AT VOUT, dm = 4V p-p
–70
HD2 AT VOUT, dm = 2V p-p
–90
–100
3
+VS = +3V, –VS = 0V
VOUT, dm = 2V p-p
–30
–40
–80
2
Figure 34. Harmonic Distortion vs. VOUT, dm for Various Supplies, f = 1 MHz
(LFCSP)
VOUT, dm = 2V p-p
–60
1
VOUT, dm (V p-p)
–20
–150
–2.5
VS = ±3.5V HD2
VS = ±2.5V HD2
–90
–130
LFCSP: RL = 200Ω
0.1
–60
–120
FREQUENCY (MHz)
HARMONIC DISTORTION (dBc)
VS = ±1.5V HD3
–50
08452-027
–80
–130
0.01
HD3 AT VOUT, dm = 2V p-p
–110
–60
–70
–80
10
Figure 33. Harmonic Distortion vs. Frequency for Various VOUT, dm (LFCSP)
HD3, RF = RG = 1kΩ
–120
–130
1
HD2, RF = RG = 499Ω
–110
–140
0.01
FREQUENCY (MHz)
HD3, RF = RG = 499Ω
–90
–100
–130
0.01
0.1
VOUT, dm = 2V p-p
–50
–120
08452-026
HARMONIC DISTORTION (dBc)
VS = ±1.5V HD2
–40
–40
–30
f = 1MHz
–30
HD2, RF = RG = 1kΩ
0.1
1
FREQUENCY (MHz)
10
08452-029
–30
–20
VOUT, dm = 2V p-p
08452-030
SPURIOUS-FREE DYNAMIC RANGE (dBc)
–20
Figure 36. Harmonic Distortion vs. Frequency for Various RF and RG (LFCSP)
Rev. D | Page 15 of 30
ADA4940-1/ADA4940-2
10
Data Sheet
–60
VOUT, dm = 2V p-p
(ENVELOPE)
0
VOUT, dm = 2V p-p
–70
–20
–80
–30
CROSSTALK (dB)
NORMALIZED SPECTRUM (dBc)
–10
–40
–50
–60
–70
–80
CHANNEL 1 TO CHANNEL 2
–90
–100
–110
–90
CHANNEL 2 TO CHANNEL 1
–100
–120
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.3
2.4
FREQUENCY (MHz)
2.5
–130
0.1
08452-033
Figure 40. Crosstalk vs. Frequency, ADA4940-2
130
120
120
110
100
110
LFCSP
90
90
80
SOIC
–PSRR
80
PSRR (dB)
70
60
70
+PSRR
50
60
40
50
10
100
FREQUENCY (MHz)
20
0.1
08452-100
1
10
1
100
FREQUENCY (MHz)
Figure 38. CMRR vs. Frequency
Figure 41. PSRR vs. Frequency
–10
100
VOUT, dm = 2V p-p
–20
GAIN (dB)
–30
–40
–50
–60
–70
0
90
–15
80
–30
70
–45
60
–60
50
–75
40
–90
30
–105
20
–120
10
–135
0
–150
–10
–165
–20
–180
1
10
FREQUENCY (MHz)
100
08452-032
–30
–80
0.1
08452-034
30
Figure 39. Output Balance vs. Frequency
–40
10k
–195
100k
1M
10M
100M
FREQUENCY (Hz)
Figure 42. Open-Loop Gain and Phase vs. Frequency
Rev. D | Page 16 of 30
PHASE (Degrees)
CMRR (dB)
100
OUTPUT BALANCE (dB)
100
FREQUENCY (MHz)
Figure 37. 2 MHz Intermodulation Distortion (LFCSP)
40
0.1
10
1
–210
1G
08452-035
–120
1.5
08452-039
–110
Data Sheet
ADA4940-1/ADA4940-2
8
2.0
G = +2
0.5
0.4
1.6
6
VOUT, dm
1.2
VOLTAGE (V)
0.8
2
2 × VIN
0
–2
0.2
OUTPUT
0.4
0.1
%ERROR
0
ERROR (%)
OUTPUT VOLTAGE (V)
4
0
–0.4
–0.1
–0.8
–0.2
–1.2
–0.3
–4
100
200
300
400
500
600
700
800
900
1000
TIME (ns)
0
10
20
30
40
50
60
–0.5
80
70
TIME (ns)
Figure 43. Output Overdrive Recovery, G = 2
Figure 46. 0.1% Settling Time
100
10
1k
10k
100k
1M
10M
FREQUENCY (Hz)
1
0.1
0.01
0.1
0
2.50
–0.25
2.25
–0.50
2.00
–2.5V
–FB DISABLE
–OUT
+IN
DISABLE
0.25
–1.25
VOCM
0
0.1µF
VICM
–1.50
+OUT
–IN
–0.25
–1.75
+FB
R1
–0.50
R2
–1.00
–2.5V
–2.00
+OUT, VICM = 1V
0
0V
+2.5V
R2
R1
–FB DISABLE
–0.25
–2.5V
DISABLE
–OUT
+IN
–0.50
VOCM
1.75
OUTPUT VOLTAGE (V)
+2.5V
R2
R1
0.50
–0.75
0V
DISABLE PIN VOLTAGE (V)
1.50
0.75
100
Figure 47. Closed-Loop Output Impedance Magnitude vs. Frequency, G = 1
1.25
–OUT, VICM = 1V
10
FREQUENCY (MHz)
Figure 44. Voltage Noise Spectral Density, Referred to Input
1.00
1
0.1µF
VICM
–0.75
+OUT
–IN
+FB
1.50
R1
R2
–1.00
–2.5V
1.25
–1.25
1.00
–1.50
0.75
–1.75
–OUT, VICM = 1V
0.50
–2.00
+OUT, VICM = 1V
0.25
–1.00
–2.50
0
–2.50
–1.25
–2.75
100
–0.25
–2.75
2.0
0
10
20
30
40
50
60
70
80
TIME (µs)
90
08452-038
–2.25
–0.75
Figure 45. DISABLE Pin Turn-Off Time
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
–2.25
1.6
TIME (µs)
Figure 48. DISABLE Pin Turn-On Time
Rev. D | Page 17 of 30
DISABLE PIN VOLTAGE (V)
100
08452-037
1
10
10
08452-040
OUTPUT IMPEDANCE (Ω)
100
INPUT VOLTAGE NOISE (nV/√Hz)
–0.4
VOUT, dm = 2V p-p
1.8
08452-057
0
–2.0
08452-041
–8
–1.6
08452-065
–6
OUTPUT VOLTAGE (V)
0.3
INPUT
ADA4940-1/ADA4940-2
Data Sheet
100
1.5
G = 1, RL = 200Ω
G = 2, RL = 200Ω
40
1.0
OUTPUT VOLTAGE (V)
G = 2, RL = 1kΩ
20
G = 1, RL = 1kΩ
0
–20
–40
–60
G
G
G
G
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
–1.5
08452-042
0
= 1,
= 1,
= 2,
= 2,
RL = 1kΩ
RL = 200Ω
RL = 1kΩ
RL = 200Ω
VOUT, dm = 2V p-p
Figure 49. Small Signal Transient Response for Various Gains and Loads
(LFCSP)
0
20 40 60 80 100 120 140 160 180 200 220 240 260 280 300
TIME (ns)
Figure 52. Large Signal Transient Response for Various Gains and Loads
100
1.5
80
VS = ±3.5V
VS = ±1.5V
OUTPUT VOLTAGE (V)
40
VS = ±1.5V
1.0
60
OUTPUT VOLTAGE (mV)
–0.5
VOUT, dm = 0.1V p-p
TIME (ns)
VS = ±2.5V
20
0
–20
–40
–60
VS = ±2.5V
0.5
0
–0.5
–1.0
–80
VS = ±3.5V
VOUT, dm = 0.1V
0
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
TIME (ns)
–1.5
08452-043
–100
0
–1.0
–80
–100
0.5
VOUT, dm = 2V p-p
0
20 40 60 80 100 120 140 160 180 200 220 240 260 280 300
TIME (ns)
Figure 50. Small Signal Transient Response for Various Supplies (LFCSP)
08452-046
OUTPUT VOLTAGE (mV)
60
08452-045
80
Figure 53. Large Signal Transient Response for Various Supplies
100
1.5
80
1.0
OUTPUT VOLTAGE (V)
40
20
0
CCOM1 = CCOM2 = 0pF
CCOM1 = CCOM2 = 0.5pF
CCOM1 = CCOM2 = 1pF
CCOM1 = CCOM2 = 2pF
–20
–40
–60
0
CCOM1 = CCOM2 = 0pF
CCOM1 = CCOM2 = 0.5pF
CCOM1 = CCOM2 = 1pF
CCOM1 = CCOM2 = 2pF
–0.5
–1.0
CDIFF = 0pF
VOUT, dm = 0.1V p-p
0
CDIFF = 0pF
VOUT, dm = 2V p-p
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
TIME (ns)
–1.5
08452-044
–80
–100
0.5
Figure 51. Small Signal Transient Response for Various Capacitive Loads
(LFCSP)
0
20 40 60 80 100 120 140 160 180 200 220 240 260 280 300
TIME (ns)
08452-047
OUTPUT VOLTAGE (mV)
60
Figure 54. Large Signal Transient Response for Various Capacitive Loads
Rev. D | Page 18 of 30
Data Sheet
ADA4940-1/ADA4940-2
100
80
60
40
20
0
–20
–40
–60
40
20
0
–20
–40
–60
–80
VOUT, dm = 0.1V p-p
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
TIME (ns)
08452-204
0
–100
Figure 55. Small Signal Transient Response for Various Packages, CL = 0 pF
VOUT, dm = 0.1V p-p
0
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
TIME (ns)
08452-206
–80
–100
LFCSP-1
LFCSP-2: CH1
LFCSP-2: CH2
SOIC-1
80
OUTPUT VOLTAGE (mV)
60
OUTPUT VOLTAGE (mV)
100
LFCSP-1
LFCSP-2: CH1
LFCSP-2: CH2
SOIC-1
Figure 57. Small Signal Transient Response for Various Packages, CL = 2 pF
1.00
100
80
0.75
VS = ±2.5V
VS = ±2.5V
OUTPUT VOLTAGE (V)
0.50
40
VS = ±1.5V
20
0
–20
–40
VS = ±1.5V
0.25
0
–0.25
–0.50
–60
–0.75
–100
VOUT, dm = 0.1V p-p
0
VOUT, dm = 1V p-p
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
TIME (ns)
Figure 56. VOCM Small Signal Transient Response
–1.00
0
20 40 60 80 100 120 140 160 180 200 220 240 260 280 300
TIME (ns)
Figure 58. VOCM Large Signal Transient Response
Rev. D | Page 19 of 30
08452-053
–80
08452-048
OUTPUT VOLTAGE (mV)
60
ADA4940-1/ADA4940-2
Data Sheet
TEST CIRCUITS
1kΩ
NETWORK
ANALYZER
OUTPUT
50Ω
475Ω
1kΩ
52.3Ω
VIN
NETWORK
ANALYZER
INPUT
+2.5V
ADA4940-1/
ADA4940-2
VOCM
1kΩ
50Ω
54.9Ω
54.9Ω
50Ω
475Ω
08452-067
25.5Ω
–2.5V
1kΩ
Figure 59. Equivalent Basic Test Circuit
1kΩ
DC-COUPLED
GENERATOR
VIN
1kΩ
LOW-PASS
FILTER
52.3Ω
VOCM
100Ω
475Ω
ADA4940-1/
ADA4940-2
1kΩ
54.9Ω
2:1
50Ω
DUAL
FILTER
HP
LP
CT
475Ω 54.9Ω
25.5Ω
–2.5V
1kΩ
Figure 60. Test Circuit for Distortion Measurements
Rev. D | Page 20 of 30
08452-056
50Ω
+2.5V
Data Sheet
ADA4940-1/ADA4940-2
TERMINOLOGY
Common-Mode Offset Voltage
DEFINITION OF TERMS
The common-mode offset voltage is defined as the difference
between the voltage applied to the VOCM terminal and the
common mode of the output voltage.
–FB
RF
+IN
–OUT
+VOCM
–DIN
RG
–IN
VOS, cm = VOUT, cm − VOCM
–
RL, dm
VOUT, dm
ADA4940-1/
ADA4940-2
+OUT
RF
+FB
Differential VOS, Differential CMRR, and VOCM CMRR
+
The differential mode and common-mode voltages each have
their own error sources. The differential offset (VOS, dm) is the
voltage error between the +IN and −IN terminals of the amplifier.
Differential CMRR reflects the change of VOS, dm in response to
changes to the common-mode voltage at the input terminals
+DIN and −DIN.
08452-090
+DIN
RG
Figure 61. Circuit Definitions
Differential Voltage
Differential voltage refers to the difference between two node
voltages. For example, the differential output voltage (or
equivalently, output differential mode voltage) is defined as
VOUT, dm = (V+OUT − V−OUT)
where V+OUT and V−OUT refer to the voltages at the +OUT and
−OUT terminals with respect to a common reference.
CMRR DIFF 
VOCM CMRR reflects the change of VOS, dm in response to
changes to the common-mode voltage at the output terminals.
CMRRVOCM 
Similarly, the differential input voltage is defined as
VIN, dm = (+DIN − (−DIN))
Common-Mode Voltage (CMV)
CMV refers to the average of two node voltages. The output
common-mode voltage is defined as
VOUT, cm = (V+OUT + V−OUT)/2
ΔV IN, cm
ΔVOS, dm
ΔVOCM
ΔVOS, dm
Balance
Balance is a measure of how well the differential signals are
matched in amplitude; the differential signals are exactly 180°
apart in phase. By this definition, the output balance is the
magnitude of the output common-mode voltage divided by
the magnitude of the output differential mode voltage.
Similarly, the input common-mode voltage is defined as
Output Balance Error 
VIN, cm = (+DIN + (−DIN))/2
Rev. D | Page 21 of 30
VOUT , cm
VOUT , dm
ADA4940-1/ADA4940-2
Data Sheet
THEORY OF OPERATION
The ADA4940-1/ADA4940-2 are high speed, low power
differential amplifiers fabricated on Analog Devices advanced
dielectrically isolated SiGe bipolar process. They provide two
closely balanced differential outputs in response to either
differential or single-ended input signals. An external feedback
network that is similar to a voltage feedback operational
amplifier sets the differential gain. The output common-mode
voltage is independent of the input common-mode voltage and
is set by an external voltage at the VOCM terminal. The PNP
input stage allows input common-mode voltages between the
negative supply and 1.2 V below the positive supply. A rail-torail output stage supplies a wide output voltage range. The
DISABLE pin can reduce the supply current of the amplifier to
13.5 μA.
Figure 62 shows the ADA4940-1/ADA4940-2 architecture.
The differential feedback loop consists of the differential transconductance GDIFF working through the GO output buffers and
the RF/RG feedback networks. The common-mode feedback
loop is set up with a voltage divider across the two differential
outputs to create an output voltage midpoint and a commonmode transconductance, GCM.
+DIN
RG
RF
CC
GO
The differential feedback loop forces the voltages at +IN and −IN
to equal each other. This fact sets the following relationships:
V
 DIN
  OUT
RG
RF
V
 DIN
  OUT
RG
RF
Subtracting the previous equations gives the relationship that
shows RF and RG setting the differential gain.
(V+OUT − V−OUT) = (+DIN – (−DIN)) ×
The common-mode feedback loop drives the output commonmode voltage that is sampled at the midpoint of the output
voltage divider to equal the voltage at VOCM. This results in the
following relationships:
VREF
GO
–DIN
RG
VOCM
+OUT
CC
RF
V−OUT = VOCM −
VOUT, dm
2
08452-058
–IN
VOUT, dm
Note that the differential amplifier’s summing junction input
voltages, +IN and −IN, are set by both the output voltages and
the input voltages.
–OUT
GCM
V+OUT = VOCM +
2
+IN
GDIFF
RF
RG
Figure 62. ADA4940-1/ADA4940-2 Architectural Block
Rev. D | Page 22 of 30
 RF
V IN   DIN 
 RF  RG
 RG

  VOUT 
R R

G
 F





 RF
V IN   DIN 
 RF  RG
 RG

  VOUT 
R R

G
 F





Data Sheet
ADA4940-1/ADA4940-2
APPLICATIONS INFORMATION
VnRG1
ANALYZING AN APPLICATION CIRCUIT
The ADA4940-1/ADA4940-2 use open-loop gain and negative
feedback to force their differential and common-mode output
voltages in such a way as to minimize the differential and commonmode error voltages. The differential error voltage is defined as
the voltage between the differential inputs labeled +IN and −IN (see
Figure 61). For most purposes, this voltage is zero. Similarly, the
difference between the actual output common-mode voltage and
the voltage applied to VOCM is also zero. Starting from these two
assumptions, any application circuit can be analyzed.
+
inIN–
VIN , dm
VnIN
ADA4940-1/
ADA4940-2
VnOD
VnRG2
RG2
RF2
VnCM
VnRF2
08452-050
VOCM
Figure 63. ADA4940-1/ADA4940-2 Noise Model
Determine the differential mode gain of the circuit in Figure 61
by using the following equation:

VnRF1
RF1
inIN+
SETTING THE CLOSED-LOOP GAIN
VOUT , dm
RG1
RF
RG
As with conventional op amp, the output noise voltage densities
can be estimated by multiplying the input-referred terms at +IN
and −IN by the appropriate output factor,
where:
GN 
This assumes that the input resistors (RG) and feedback resistors
(RF) on each side are equal.
ESTIMATING THE OUTPUT NOISE VOLTAGE
Estimate the differential output noise of the ADA4940-1/
ADA4940-2 by using the noise model in Figure 63. The inputreferred noise voltage density, vnIN, is modeled as a differential
input, and the noise currents, inIN− and inIN+, appear between
each input and ground. The noise currents are assumed equal
and produce a voltage across the parallel combination of the gain
and feedback resistances. vnCM is the noise voltage density at the
VOCM pin. Each of the four resistors contributes (4kTRx)1/2. Table 14
summarizes the input noise sources, the multiplication factors,
and the output-referred noise density terms. For more noise
calculation information, go to the Analog Devices Differential
Amplifier Calculator (DiffAmpCalc™), click
ADIDiffAmpCalculator.zip, and follow the on-screen prompts.
β1 
2
β1  β2 
is the circuit noise gain.
RG1
RG2
and β2 
are the feedback factors.
RF1  RG1
RF2  RG2
When RF1/RG1 = RF2/RG2, then β1 = β2 = β, and the noise gain
becomes
GN 
R
1
1 F
β
RG
Note that the output noise from VOCM goes to zero in this case.
The total differential output noise density, vnOD, is the root-sumsquare of the individual output noise terms.
vnOD 
8
2
 vnOi
i 1
Table 14. Output Noise Voltage Density Calculations
Input Noise Contribution
Differential Input
Inverting Input
Noninverting Input
VOCM Input
Gain Resistor RG1
Gain Resistor RG2
Feedback Resistor RF1
Feedback Resistor RF2
Input Noise Term
vnIN
inIN−
inIN+
vnCM
vnRG1
vnRG2
vnRF1
vnRF2
Input Noise
Voltage Density
vnIN
inIN− × (RG2||RF2)
inIN+ × (RG1||RF1)
vnCM
(4kTRG1)1/2
(4kTRG2)1/2
(4kTRF1)1/2
(4kTRF2)1/2
Rev. D | Page 23 of 30
Output
Multiplication Factor
GN
GN
GN
GN (β1 − β2)
GN (1 − β2)
GN (1 − β1)
1
1
Output-Referred Noise
Voltage Density Term
vnO1 = GN (vnIN)
vnO2 = GN [inIN− × (RG2||RF2)]
vnO3 = GN [inIN+ × (RG1||RF1)]
vnO4 = GN (β1 − β2)(vnCM)
vnO5 = GN (1 − β2)(4kTRG1)1/2
vnO6 = GN (1 − β1)(4kTRG2)1/2
vnO7 = (4kTRF1)1/2
vnO8 = (4kTRF2)1/2
ADA4940-1/ADA4940-2
Data Sheet
Table 15 and Table 16 list several common gain settings, recommended resistor values, input impedances, and output noise density for both
balanced and unbalanced input configurations.
Table 15. Differential Ground-Referenced Input, DC-Coupled, RL = 1 kΩ (See Figure 64)
Nominal Gain (dB)
0
6
10
14
RF (Ω)
1000
1000
1000
1000
RG (Ω)
1000
500
318
196
RIN, dm (Ω)
2000
1000
636
392
Differential Output Noise Density (nV/√Hz)
11.3
15.4
20.0
27.7
RTI (nV/√Hz)
11.3
7.7
6.8
5.5
Table 16. Single-Ended Ground-Referenced Input, DC-Coupled, RS = 50 Ω, RL = 1 kΩ (See Figure 65)
Nominal Gain (dB)
0
6
10
14
RG (Ω)
1000
500
318
196
RT (Ω)
52.3
53.6
54.9
59.0
RIN, se (Ω)
1333
750
512
337
RG1 (Ω)1
1025
526
344
223
Differential Output Noise Density (nV/√Hz)
11.2
15.0
19.0
25.3
RTI (nV/√Hz)
11.2
7.5
6.3
5
RG1 = RG + (RS||RT)
Even if the external feedback networks (RF/RG) are mismatched,
the internal common-mode feedback loop still forces the outputs
to remain balanced. The amplitudes of the signals at each output
remain equal and 180° out of phase. The input-to-output,
differential mode gain varies proportionately to the feedback
mismatch, but the output balance is unaffected.
For an unbalanced, single-ended input signal (see Figure 65),
the input impedance is




RG


R IN , se 
RF


 1  2  R  R  
G
F 

RF
+VS
As well as causing a noise contribution from VOCM, ratio-matching
errors in the external resistors result in a degradation of the ability
of the circuit to reject input common-mode signals, much the
same as for a four resistors difference amplifier made from a
conventional op amp.
In addition, if the dc levels of the input and output commonmode voltages are different, matching errors result in a small
differential mode, output offset voltage. When G = 1, with a
ground-referenced input signal and the output common-mode
level set to 2.5 V, an output offset of as much as 25 mV (1% of
the difference in common-mode levels) can result if 1% tolerance
resistors are used. Resistors of 1% tolerance result in a worstcase input CMRR of about 40 dB, a worst-case differential mode
output offset of 25 mV due to the 2.5 V level-shift, and no
significant degradation in output balance error.
+DIN
–DIN
RG
+IN
VOCM
RG
ADA4940-1/
ADA4940-2
VOUT, dm
–IN
08452-051
IMPACT OF MISMATCHES IN THE FEEDBACK
NETWORKS
RF
Figure 64. ADA4940-1/ADA4940-2 Configured for Balanced (Differential) Inputs
RF
+VS
RG
RS
+IN
VOCM
RT
RG
RS
RT
ADA4940-1/
ADA4940-2
VOUT, dm
–IN
RF
CALCULATING THE INPUT IMPEDANCE OF AN
APPLICATION CIRCUIT
08452-052
1
RF (Ω)
1000
1000
1000
1000
Figure 65. ADA4940-1/ADA4940-2 Configured for
Unbalanced (Single-Ended) Input
The effective input impedance of a circuit depends on whether
the amplifier is being driven by a single-ended or differential
signal source. For balanced differential input signals, as shown
in Figure 64, the input impedance (RIN, dm) between the inputs
(+DIN and −DIN) is simply RIN, dm = 2 × RG.
The input impedance of the circuit is effectively higher than it
would be for a conventional op amp connected as an inverter
because a fraction of the differential output voltage appears at
the inputs as a common-mode signal, partially bootstrapping
the voltage across the input resistor RG1.
Rev. D | Page 24 of 30
ADA4940-1/ADA4940-2
RS
Terminating a Single-Ended Input
This section describes how to properly terminate a single-ended
input to the ADA4940-1/ADA4940-2 with a gain of 1, RF = 1 kΩ
and RG = 1 kΩ. An example using an input source with a terminated
output voltage of 1 V p-p and source resistance of 50 Ω illustrates
the three steps that must be followed. Because the terminated
output voltage of the source is 1 V p-p, the open-circuit output
voltage of the source is 2 V p-p. The source shown in Figure 66
indicates this open-circuit voltage.
VS
2V p-p
RF
+VS
RG
1kΩ
1kΩ
+VS
ADA4940-1
ADA4940-2
VOCM
RG
RL VOUT, dm
VTH
1.02V p-p
RTH
RG
25.5Ω
1kΩ
VOCM
1kΩ
RG
RTS
25.5Ω
–VS
08452-059
RF
1kΩ
1kΩ
The input impedance is calculated by
Figure 69. Thevenin Equivalent and Matched Gain Resistors
Figure 69 presents a tractable circuit with matched feedback
loops that can be easily evaluated.
It is useful to point out two effects that occur with a terminated
input. The first is that the value of RG is increased in both loops,
lowering the overall closed-loop gain. The second is that VTH
is a little larger than 1 V p-p, as it would be if RT = 50 Ω.
These two effects have opposite impacts on the output voltage,
and for large resistor values in the feedback loops (~1 kΩ), the
effects essentially cancel each other out. For small RF and RG,
or high gains, however, the diminished closed-loop gain is not
cancelled completely by the increased VTH. This can be seen by
evaluating Figure 69.
To match the 50 Ω source resistance, calculate the
termination resistor, RT, using RT||1.33 kΩ = 50 Ω.
The closest standard 1% value for RT is 52.3 Ω.
RF
1kΩ
+VS
RIN, se
50Ω
VS
2V p-p
RS
RG
50Ω
1kΩ
RT
52.3Ω
VOCM
RG
ADA4940-1
ADA4940-2
RL
The desired differential output in this example is 1 V p-p
because the terminated input signal was 1 V p-p and the
closed-loop gain = 1. The actual differential output voltage,
however, is equal to (1.02 V p-p)(1000/1025.5) = 0.996 V p-p.
This is within the tolerance of the resistors, so no change to
the feedback resistor, RF, is required.
VOUT, dm
1kΩ
–VS
08452-060
RF
1kΩ
Figure 67. Adding Termination Resistor RT
3.
1kΩ
–VS


 


 
R
1000
G
  1.33 kΩ
 
RIN , se  
1000

RF

 
1

1



 
2
(
1000
1000
)


2
(
)


R
R
F
G
 


2.
RL VOUT, dm
RF
Figure 66. Calculating Single-Ended Input Impedance, RIN
1.
ADA4940-1
ADA4940-2
08452-062
RS
50Ω
VTH
1.02V p-p
25.5Ω
Figure 68. Calculating the Thevenin Equivalent
1kΩ
RIN, se
1.33kΩ
RTH
RT
52.3Ω
RTS = RTH = RS||RT = 25.5 Ω. Note that VTH is greater than
1 V p-p, which was obtained with RT = 50 Ω. The modified
circuit with the Thevenin equivalent (closest 1% value used for
RTH) of the terminated source and RTS in the lower feedback
loop is shown in Figure 69.
RF
VS
2V p-p
50Ω
08452-061
Data Sheet
INPUT COMMON-MODE VOLTAGE RANGE
Figure 67 shows that the effective RG in the upper feedback
loop is now greater than the RG in the lower loop due to the
addition of the termination resistors. To compensate for the
imbalance of the gain resistors, add a correction resistor (RTS)
in series with RG in the lower loop. RTS is the Thevenin
equivalent of the source resistance, RS, and the termination
resistance, RT, and is equal to RS||RT.
The ADA4940-1/ADA4940-2 input common-mode range is
shifted down by approximately 1 VBE, in contrast to other ADC
drivers with centered input ranges, such as the ADA4939-1/
ADA4939-2. The downward-shifted input common-mode range
is especially suited to dc-coupled, single-ended-to-differential,
and single-supply applications.
For ±2.5 V or +5 V supply operation, the input common-mode
range at the summing nodes of the amplifier is specified as −2.7 V
to +1.3 V or −0.2 V to 3.8 V, and is specified as −0.2 V to +1.8 V
with a +3 V supply.
Rev. D | Page 25 of 30
ADA4940-1/ADA4940-2
Data Sheet
+VS
INPUT AND OUTPUT CAPACITIVE AC COUPLING
AMPLIFIER
BIAS CURRENT
DISABLE
08452-063
Although the ADA4940-1/ADA4940-2 is best suited to dccoupled applications, it is nonetheless possible to use it in accoupled circuits. Input ac coupling capacitors can be inserted
between the source and RG. This ac coupling blocks the flow
of the dc common-mode feedback current and causes the
ADA4940-1/ADA4940-2 dc input common-mode voltage to
equal the dc output common-mode voltage. These ac coupling
capacitors must be placed in both loops to keep the feedback
factors matched. Output ac coupling capacitors can be placed in
series between each output and its respective load.
–VS
Figure 70. DISABLE Pin Circuit
SETTING THE OUTPUT COMMON-MODE VOLTAGE
DRIVING A CAPACITIVE LOAD
The VOCM pin of the ADA4940-1/ADA4940-2 is internally
biased at a voltage approximately equal to the midsupply point,
[(+VS) + (−VS)]/2. Relying on this internal bias results in an
output common-mode voltage that is within approximately
100 mV of the expected value.
A purely capacitive load reacts with the bond wire and pin
inductance of the ADA4940-1/ADA4940-2, resulting in high
frequency ringing in the transient response and loss of phase
margin. One way to minimize this effect is to place a resistor in
series with each output to buffer the load capacitance. The resistor
and load capacitance form a first-order, low-pass filter; therefore,
the resistor value must be as small as possible. In some cases,
the ADCs require small series resistors to be added on their inputs.
DISABLE PIN
The ADA4940-1/ADA4940-2 feature a DISABLE pin that can
be used to minimize the quiescent current consumed when the
device is not being used. DISABLE is asserted by applying a low
logic level to the DISABLE pin. The threshold between high and
low logic levels is nominally 1.4 V above the negative supply rail.
See Table 5 and Table 8 for the threshold limits.
120
VIN
+2.5V
R4
R3
–FB
100
The DISABLE pin features an internal pull-up network that
enables the amplifier for normal operation. The ADA4940-1/
ADA4940-2 DISABLE pin can be left floating (that is, no
external connection is required) and does not require an
external pull-up resistor to ensure normal on operation (see
Figure 70). When the ADA4940-1/ADA4940-2 is disabled, the
output is high impedance. Note that the outputs are tied to the
inputs through the feedback resistors and to the source using the
gain resistors. In addition, there are back-to-back diodes on the
input pins that limit the differential voltage to 1.2 V.
Rev. D | Page 26 of 30
–OUT
+IN
RS
CL
VOCM
0.1µF
80
CL
+OUT
–IN
RS
+FB
R1
R2
–2.5V
60
40
20
0
5
10
100
LOAD CAPACITANCE (pF)
Figure 71. Capacitive Load vs. Series Resistance (LFCSP)
1000
08452-064
It is also possible to connect the VOCM input to a common-mode
level (CML) output of an ADC. However, care must be taken to
ensure that the output has sufficient drive capability. The input
impedance of the VOCM pin is approximately 250 kΩ.
Figure 71 illustrates the capacitive load vs. the series resistance
required to maintain a minimum 45° of phase margin.
SERIES RESISTANCE (Ω)
In cases where more accurate control of the output common-mode
level is required, it is recommended that an external source, or
resistor divider (10 kΩ or greater resistors), be used. The output
common-mode offset listed in the Specifications section assumes
that the VOCM input is driven by a low impedance voltage source.
Data Sheet
ADA4940-1/ADA4940-2
The total system power in Figure 73 is under 35 mW. A large
portion of that power is the current coming from supplies to the
output, which is set at 2.5 V, going back to the input through the
feedback and gain resistors. To reduce that power to 25 mW,
increase the value of the feedback and gain resistor from 1 kΩ
to 2 kΩ and set the value of the resistors R5 and R6 to 3 kΩ. The
ADR435 is used to regulate the +6 V supply to +5 V, which ends
up powering the ADC and setting the reference voltage for the
VOCM pin.
Figure 72 shows the fft of a 20 kHz differential input tone
sampled at 1 MSPS. The second and third harmonics are down
at −118 dBc and −122 dBc.
0
–20
–40
–60
–80
–100
–120
–140
In this example, the signal generator has a 10 V p-p symmetric,
ground-referenced bipolar output. The VOCM input is bypassed for
noise reduction and set externally with 1% resistors to 2.5 V to
maximize the output dynamic range. With an output common-
–160
0
20k
40k
60k
FREQUENCY (Hz)
ADR435
+5V
R3
10µF
+6V
R4
–FB
+2.5V
+IN
–OUT
R5
VOCM
33Ω
2.7nF
ADA4940-1
2.7nF
0.1µF
+OUT
33Ω
IN+
REF
VDD
AD7982
IN–
GND
–IN
SERIAL
INTERFACE
+FB
–DIN
R1
R2
–1V
Figure 73. ADA4940-1 (LFCSP) Driving the AD7982 ADC
Rev. D | Page 27 of 30
08452-066
R6
100k
Figure 72. Distortion Measurement of a 20 kHz Input Tone (See CN-0237)
+6V
+DIN
80k
08452-069
The ADA4940-1/ADA4940-2 are ideally suited for broadband
dc-coupled applications. The circuit in Figure 73 shows a frontend connection for an ADA4940-1 driving an AD7982, which is
an 18-bit, 1 MSPS successive approximation, analog-to-digital
converter (ADC) that operates from a single power supply, 3 V
to 5 V. It contains a low power, high speed, 18-bit sampling
ADC and a versatile serial interface port. The reference voltage,
REF, is applied externally and can be set independent of the
supply voltage. As shown in Figure 73, the ADA4940-1 is dccoupled on the input and the output, which eliminates the need
for a transformer to drive the ADC. The amplifier performs a
single-ended-to-differential conversion if needed and level
shifts the input signal to match the input common mode of the
ADC. The ADA4940-1 is configured with a dual 7 V supply
(+6 V and −1 V) and a gain that is set by the ratio of the
feedback resistor to the gain resistor. In addition, the circuit
can be used in a single-ended-input-to-differential output or
differential-input-to-differential output configuration. If needed,
a termination resistor in parallel with the source input can be
used. Whether the input is a single-ended input or differential,
the input impedance of the amplifier can be calculated as shown in
the Terminating a Single-Ended Input section. If R1 = R2 = R3 =
R4 = 1 kΩ, the single-ended input impedance is approximately
1.33 kΩ, which, in parallel with a 52.3 Ω termination resistor,
provides a 50 Ω termination for the source. An additional 25.5 Ω
(1025.5 Ω total) at the inverting input balances the parallel
impedance of the 50 Ω source and the termination resistor driving
the noninverting input. However, if a differential source input is
used, the differential input impedance is 2 kΩ. In this case, two
52.3 Ω termination resistors are used to terminate the inputs.
mode voltage of 2.5 V, each ADA4940-1 output swings between
0 V and 5 V, opposite in phase, providing a gain of 1 and a
10 V p-p differential signal to the ADC input. The differential RC
section between the ADA4940-1 output and the ADC provides
single-pole, low-pass filtering with a corner frequency of 1.79 MHz
and extra buffering for the current spikes that are output from the
ADC input when its sample-and-hold (SHA) capacitors are
discharged.
AMPLITUDE (dB)
DRIVING A HIGH PRECISION ADC
ADA4940-1/ADA4940-2
Data Sheet
LAYOUT, GROUNDING, AND BYPASSING
As a high speed device, the ADA4940-1/ADA4940-2 are
sensitive to the PCB environment in which they operate.
Realizing their superior performance requires attention to
the details of high speed PCB design.
Bypass the power supply pins as close to the device as possible
and directly to a nearby ground plane. Use high frequency ceramic
chip capacitors. Use two parallel bypass capacitors (1000 pF and
0.1 μF) for each supply. Place the 1000 pF capacitor closer to the
device. Further away, provide low frequency bypassing using
10 μF tantalum capacitors from each supply to ground.
ADA4940-1 LFCSP EXAMPLE
The first requirement is a solid ground plane that covers as
much of the board area around the ADA4940-1 as possible.
However, clear the area near the feedback resistors (RF), gain
resistors (RG), and the input summing nodes (Pin 2 and Pin 3)
of all ground and power planes (see Figure 74). Clearing the
ground and power planes minimizes any stray capacitance at
these nodes and prevents peaking of the response of the
amplifier at high frequencies.
Ensure that signal routing is short and direct to avoid parasitic
effects. Wherever complementary signals exist, provide a
symmetrical layout to maximize balanced performance. When
routing differential signals over a long distance, ensure that
PCB traces are close together, and twist any differential wiring
such that loop area is minimized. Doing this reduces radiated
energy and makes the circuit less susceptible to interference.
1.30
The thermal resistance, θJA, is specified for the device, including
the exposed pad, soldered to a high thermal conductivity 4-layer
circuit board, as described in EIA/JESD 51-7.
0.80
08452-087
1.30 0.80
08452-086
Figure 75. Recommended PCB Thermal Attach Pad Dimensions (mm)
Figure 74. Ground and Power Plane Voiding in Vicinity of RF and RG
1.30
TOP METAL
GROUND PLANE
0.30
PLATED
VIA HOLE
08452-088
POWER PLANE
BOTTOM METAL
Figure 76. Cross-Section of 4-Layer PCB Showing Thermal Via Connection to Buried Ground Plane (Dimensions in mm)
Rev. D | Page 28 of 30
Data Sheet
ADA4940-1/ADA4940-2
OUTLINE DIMENSIONS
0.30
0.23
0.18
0.50
BSC
13
PIN 1
INDICATOR
16
1
12
EXPOSED
PAD
1.45
1.30 SQ
1.15
4
9
0.80
0.75
0.70
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
0.25 MIN
BOTTOM VIEW
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
111808-A
TOP VIEW
5
8
0.50
0.40
0.30
COMPLIANT TO JEDEC STANDARDS MO-220-WEED.
Figure 77. 16-Lead Lead Frame Chip Scale Package [LFCSP]
3 mm × 3 mm Body and 0.75 mm Package Height
(CP-16-21)
Dimensions shown in millimeters
5.00 (0.1968)
4.80 (0.1890)
4.00 (0.1574)
3.80 (0.1497)
8
1
5
4
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
COPLANARITY
0.10
SEATING
PLANE
6.20 (0.2441)
5.80 (0.2284)
1.75 (0.0688)
1.35 (0.0532)
0.51 (0.0201)
0.31 (0.0122)
0.50 (0.0196)
0.25 (0.0099)
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-012-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 78. 8-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-8)
Dimensions shown in millimeters and (inches)
Rev. D | Page 29 of 30
012407-A
PIN 1
INDICATOR
3.10
3.00 SQ
2.90
ADA4940-1/ADA4940-2
4.10
4.00 SQ
3.90
0.30
0.25
0.18
0.50
BSC
PIN 1
INDICATOR
24
19
18
1
2.65
2.50 SQ
2.45
EXPOSED
PAD
13
0.50
0.40
0.30
TOP VIEW
0.80
0.75
0.70
6
12
7
BOTTOM VIEW
3.16 MIN
0.05 MAX
0.02 NOM
COPLANARITY
0.08
SEATING
PLANE
0.25 MIN
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
0.20 REF
COMPLIANT TO JEDEC STANDARDS MO-220-WGGD.
03-11-2013-A
PIN 1
INDICATOR
Data Sheet
Figure 79. 24-Lead Lead Frame Chip Scale Package [LFCSP]
4 mm × 4 mm Body and 0.75 mm Package Height
(CP-24-7)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
ADA4940-1ACPZ-R2
ADA4940-1ACPZ-RL
ADA4940-1ACPZ-R7
ADA4940-1ARZ
ADA4940-1ARZ-RL
ADA4940-1ARZ-R7
ADA4940-2ACPZ-R2
ADA4940-2ACPZ-RL
ADA4940-2ACPZ-R7
1
Temperature Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Package Description
16-Lead LFCSP
16-Lead LFCSP
16-Lead LFCSP
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
24-Lead LFCSP
24-Lead LFCSP
24-Lead LFCSP
Z = RoHS Compliant Part.
©2011–2016 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D08452-0-5/16(D)
Rev. D | Page 30 of 30
Package Option
CP-16-21
CP-16-21
CP-16-21
R-8
R-8
R-8
CP-24-7
CP-24-7
CP-24-7
Ordering Quantity
250
5,000
1,500
98
2,500
1,000
250
5,000
1,500
Branding
H29
H29
H29