Download 299 8.1 COMBINED ANALOG/DIGITAL COMPUTING ELEMENTS

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Document related concepts

Electronic engineering wikipedia , lookup

Time-to-digital converter wikipedia , lookup

Integrated circuit wikipedia , lookup

Wien bridge oscillator wikipedia , lookup

Immunity-aware programming wikipedia , lookup

Tektronix analog oscilloscopes wikipedia , lookup

Phase-locked loop wikipedia , lookup

CMOS wikipedia , lookup

Television standards conversion wikipedia , lookup

Regenerative circuit wikipedia , lookup

Oscilloscope wikipedia , lookup

Amplifier wikipedia , lookup

HD-MAC wikipedia , lookup

Digital electronics wikipedia , lookup

Radio transmitter design wikipedia , lookup

Valve audio amplifier technical specification wikipedia , lookup

Index of electronics articles wikipedia , lookup

Broadcast television systems wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Current mirror wikipedia , lookup

Operational amplifier wikipedia , lookup

Oscilloscope types wikipedia , lookup

Power electronics wikipedia , lookup

Analog television wikipedia , lookup

Multimeter wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Schmitt trigger wikipedia , lookup

Mixing console wikipedia , lookup

Two-port network wikipedia , lookup

Transistor–transistor logic wikipedia , lookup

Integrating ADC wikipedia , lookup

Telecommunication wikipedia , lookup

Coupon-eligible converter box wikipedia , lookup

Valve RF amplifier wikipedia , lookup

Network analysis (electrical circuits) wikipedia , lookup

Oscilloscope history wikipedia , lookup

Analog-to-digital converter wikipedia , lookup

Rectiverter wikipedia , lookup

Opto-isolator wikipedia , lookup

Transcript
300
8.1
A magnitude of an input signal X of 6.68SV,
would therefore be presented as the binary number
B 101 and the dc voltage of .l.U5V. As X increases
to 7.499V the analog voltage XA increases to 1.249V.
Wnen X becomes 7.S01V XA increases first to 1.250V,
then returns to zero, and increases to .OOlV. As
XA returns to zero the binary number XD must increase by a magnitude equal to 1.25V, i.e., the 2°digi~
in order to maintain the magnitude of the total
signal constant. It is important that this changeover will be executed as quickly as possible.
Hybrid computing elements enploying DDA (Digi-
is the hybrid multiplier. The circuit described
here differs from the NBS version in that the digital input sign~s are binary numbers and not pulse
rates. This e~iminates the need for the X and Yregisters, in which the input variab~es are integrated. Without this integration considerable higher bandwidth is possib~e at the same clock frequency.
Further, instead of the con~on R-register,
which allows multiplication only by a unity step,
the device to be described emp~oys a paral~el binary multiplier 2•
The operation of the hybrid multiplier shown
tal Differential Analyzer) techniques in combina-
in Fig. 2 is based on the multiplication of two
tion with analog computing techniques have be In
developed by the National Bureau of Standards. It
will be shown later that such a system not only requires more components but its slewing time is limited by its "unit step" digital. operation. In addition, if a DDA computer once makes a mistake, as
e.g. due to power fai~ure or transients in the system, it would carry that mistake, until the computation is restarted from the initial conditions.
sums, namelyt
XY .. (Xn+XA) x (YD+YA) .. XnYn + XDYA + XAYn +XAYA
(1)
From the equation above it can be seen that the
product XY is now expressed as the sum of four
products. At first this may not ~eem to be a very
elegant solution but it will soon become apparent
The hybrid computing system described employs
that the circuits required for the individual multiplier elements are relatively simple and that
only pure digital computing techniques (in addition
to the analog techniques). Since all digital opera-, conventional circuitry can be used. From the block
diagram in Fig. 2 it can be seen that the first
tions are carried out in parallel its slewing rate
is considerably better. In addition, any momentary multiplier element is a simultaneous binary multiplier, described in the literature(2). The second
fa~lure of the input signals or the equipment has
and the third multiplier elements accept one digionly a momentary effect on the output signal.
tal and one analog Signal and thus digital to analog CD/A) converters can be used. The fourth mulFrom the generalized form of a hybrid computiplier e~ement can be a Simple, one-quadrant anating element in Fig. 1 it can be seen that all inputs and the output consist of a digital part and
lo~ multiplier.
The outputs from all but the digian analog part. The digital input signal Xn is
tal multiplier element are in analog form and must
accepted by a digital computing circuit, while the
be added in a conventional analog summing device.
analog input signal XA is accepted by an analog
The number of digits at the output of the digital
computing circuit. There is also one (or more) commultiplier is the sum of the digits of the two inputing circuit~which accept both analog and digiput signals. In order that the form of the output
tal inputs. Since the digital output must have as
signal is compatible with the form of the input
many digits as the input, the additional digits
signals the output signal should have the same nummust be converted back into an analog voltage. The
ber of digits as the input signal. This can be
outputs from the D/A converter, the Dig./Anal. com- e~sily accomplished when the output signal is ~aled,
puting circuit, and the analog computing circuit
i.e., when the binary point is shifted and when
are summed in the analog adder. If the analog sum
the least significant digits are converted back inis larger than a certain threshold voltage the
to an analog signal. The latter conversion is achcomparison circuit subtracts the threshold voltage
ieved by means of the n/A converter #3. The scalfrom the analog sum and provides a "carry" signal
ing of the output signal will be explained in greatwhich is added to the digital signal. This auger detail on hand of the specific example below.
mented digital signal is then the digital portion
of the output signal. The output from the analog
The real advantage of this multiplier can be
adder is the analog portion of the output signal.
appreciated only if the magnitudes of the accuracies required from each multiplier element are desWith the number of blocks shown in the diacribed. To simplify this description it is useful
gram of Fig. 1 a hybrid computing element seems to
to make the assumption, that both input and output
signals vary in magnitude between the equivalent
be a complicated and costly device and one begins
to wonder whether the incre,ase in cost and complexi- of 0 and ±lOV.
ty justifies the improvement in performance. HowBefore describing the scaling operation in the
ever, it will be shown that most of these blocks
multiplier for the binary system it is convenient
consist of relatively simple electronic circuits.
to describe it first for the decimal system. Assume
therefore further that the digital multiplier acTHE HYBRID MJLTIPLIER
cepts one decimal digit on each input and provides
two decimal digits at the output,and that the anaOne of the best examples on how simple and
log portion of the variable is represented by a DC
how cheaply a hybrid computing element can be built
voltage varying between 0 and 1.OOV.!f we desire now
From the collection of the Computer History Museum (www.computerhistory.org)