Download DataSheet

qGSI Equine FGF1 Primer Pairs
Tools for qPCR
Package Contents and Storage Conditions
For qGSI primer pairs:
• 1 Vial qGSI qPCR primer mix: 2 nmol lyophilized (sufficient for 200 reactions). Before use,
reconstitute the primer mix in 200 µl dH2O to make a final concentration of 10 µM.
• 1 vial positive control: lyophilized. Before use, reconstitute the primer mix in 200 µl dH2O,
• Application Guide
The above components are shipped at room temperature, but should be kept at -20°C for long term storage. If
properly stored, they have a 12 month shelf life.
NOTE: FOR RESEARCH PURPOSES ONLY. NOT FOR DIAGNOSTIC OR THERAPEUTIC USAGE.
Introduction
Heparin-binding growth factor 1 (FGF1) is encoded by this gene is a member of the fibroblast growth factor (FGF)
family. FGF family members possess broad mitogenic and cell survival activities, and are involved in a variety of
biological processes, including embryonic development, cell growth, morphogenesis, tissue repair, tumor growth
and invasion. This protein functions as a modifier of endothelial cell migration and proliferation, as well as an
angiogenic factor. It acts as a mitogen for a variety of mesoderm- and neuroectoderm-derived cells in vitro, thus is
thought to be involved in organogenesis.
The most essential component of a successful qPCR is the primers used to amplify the template. Only welldesigned primers can regulation, kinase modification, endocytosis, and regulation of other cell signaling
pathways generate a false positive signal. To design primers with a high specificity and a low incidence of primer
dimer formation, GSI conducted a large scale study of qPCR. Based on the vast qPCR data acquired through this
study, GSI scientists were able to develop a superb primer design algorithm. With this algorithm, GSI is able to
provide customers with pre-designed, ready-to-use qPCR primers. Besides high specificity and high efficiency, each
primer pair is also selected to span exon junctions whenever possible, thus avoiding the amplification of genomic
DNA.
Each individual primer pair is supplied as 2 nmol lyophilized powder. Before use, reconstitute the primer mix in
200 µl dH2O to make a final concentration of 10 µM.
The positive control is provided to help check that nothing went wrong during the procedure. Before use,
reconstitute positive control in 200 µl dH2O, and 5 µl is used for a 25 µl reaction.
-1-
For custom primer design, please contact technical support: [email protected]
qPCR Individual Primer Protocol
Each individual primer pair is supplied as 2 nmol lyophilized powder. Before use, reconstitute the primer mix in
200 µl dH2O to make a final concentration of 10 µM.
1. Transfer 5 µl of the cDNA sample to a well of the qPCR plate; add 1 µl qPCR primer pair mixture and 6.5
µl H2O.
2. Add 12.5 µl 2X SYBR Green I qGSI qPCR master mix
3. Set up the PCR run according to the machine’s user manual. Start the PCR reaction.
4. Analyze the data according to the machine’s user manual
The following conditions can be used as reference when using qGSI primer mix on ABI
7500 real time PCR system.
Pre-soak 95°C for 10 min
Denaturation 95°C for 15 sec
Annealing 60°C for 10 min
Cycles 40
*Certain SYBR Green Master mixes require a specific activation step. Refer to the manufacturer’s manual
for setting up your PCR program
Trouble-shooting Guide
No qPCR product detected
1. A qPCR component may have been omitted in the reaction. Be sure to use a checklist when
assembling the reaction mix.
2. Make sure the master mix is working by using a positive template control.
3. The sample used may have very limited qPCR template. Add more samples or prepare efficient
templates by using a better reverse transcriptase.
Wavy/Erratic Lines
1.
2.
3.
Check machine settings, See if a reference dye (ROX, or Fluorescein) was set.
Check if the machine needs calibration.
Be sure the reaction volume is not too low.
High Well-to-Well Variance
1.
2.
3.
Choose correct plates. Do not use frosted or black plates.
Use only high quality optically clear seals that have been specifically designed for fluorescence applications.
Machine needs re-calibrating
-2-
4.
Concentration gradient formed in vial Invert the mixture several times before use.
-3-