Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Direction for use FlowRest Light cured composite flowable filling material PROPERTIES FlowRest is a flowable, light-curing composite material for use in therapeutic and orthodontic stomatology. The monomer matrix contains Bis GMA, urethane dimethacrylate, and triethylene glycol dimethacrylate. The inorganic filler particles compose barium glass, ytterbium trifluoride, Ba Al fluorosilicate glass, highly dispersed silicon dioxide, and spheroid mixed oxide, сatalysts, stabilizers, and pigments. The total content of inorganic fillers is 68% wt. The mean particle size is 0.7 pm. FlowRest hardens with light in the wave length range of 400-500 nm. FlowRest is available in the following VITA shades: A1, A2, A3, A3.5, B3, A4. INDICATION -Class V restorations (cervical caries, root erosion, wedge-shaped defects) -Anterior restorations (Classes III and IV) -Small posterior restorations -Restorative therapy for mini-cavities of all types -Adhesive cementation of inlays -Preventive resin restorations in premolars and molars -Repair of composite/ceramic veneers -Blocking out of undercuts -Adhesive cementation of ceramic and composite restorations. CLINICAL PROCEDURE While working with FlowRest it is recommended to use the traditional technique of working with composite materials. Temporary and layer materials should not contain eugenol. Shade determination Clean the teeth before determining the shade. The teeth should be still moist for shade determination. Cavity preparation Appropriate isolation, best with a rubber dam or cotton roller, is required. Prepare the cavity according to the generally accepted principles, i.e. gentle treatment of the tooth tissue. Do not prepare any sharp internal edges or additional undercuts in caries-free areas. After that, clean the cavity with water spray and dry it with air, avoid overdrying dentin. Prevent the tongue or oral fluids from contact with the prepared cavity. If the cavity is deep and close to the pulp, cover the areas close to the pulp with a layer of calcium hydroxide, then with a layer of glass ionomer cement. Conditioning of enamel and dentin Apply the etching gel on the enamel for 30 seconds and on the dentin for 10 seconds to react, and then thoroughly rinse off with water. Dry the tooth surface with air, avoid overdrying dentin. If the etched tooth surface is contaminated (e.g. with saliva), repeat the etching procedure for 10 seconds. Application of the bonding agent We recommend using “Primer-Adhesive” or similar adhesive materials as the bonding agent. For further information please refer to the directions for use of these materials. Placing FlowRest Insert the material of the chosen shade into the prepared cavity with a layer of 2 mm or less directly from the syringe with a disposable needle, removing the tip and putting the needle tip on syringe. Before applying, make sure that the material flows freely through the needle tip. Then insert it into the cavity, put a layer of 2 mm and distribute it with the instrument. To prevent flowing out the material from the syringe, return the piston to the initial position. Use matrix strip to contour the filling holding it till the material hardens. Curing Expose the material with the light of 400-500 nm wavelength for 40 seconds. While restoring deep cavities using FlowRest in deeper layers of the construction, it is reasonable to use in the higher layers compatible composite materials like “UniRest”. Further treatment of the filling Polishing of the filling with dental disks, silicon instruments etc may be started after the material hardens. CONTRAINDICATION FlowRest contains methacrylate and may cause sensitization or allergic reaction with predisposed persons. FlowRest should no longer be applied in such cases. STORAGE "FLOWREST" set must be stored at the temperature not exceeding +25° C in an area protected from direct sunlight. Shelf life of the material is 3 years. If stored in refrigerator, before use FlowRest should be kept at room temperature for at least 1 hour.