X-ray imager - UWSpace - University of Waterloo
... a 32x32 flat panel X-ray detector. There are two main sections in any X-ray panel detector, Gate Drivers and Charge Amplifiers. In order to minimize the size of the circuit, which can be very large if discrete components are used for both sections, an application specific integrated circuit (ASIC) d ...
... a 32x32 flat panel X-ray detector. There are two main sections in any X-ray panel detector, Gate Drivers and Charge Amplifiers. In order to minimize the size of the circuit, which can be very large if discrete components are used for both sections, an application specific integrated circuit (ASIC) d ...
ELE2120 Digital Circuits and Systems
... Typical values for CMOS technology: tsu = tsetup = 3 ns th = thold = 2 ns ...
... Typical values for CMOS technology: tsu = tsetup = 3 ns th = thold = 2 ns ...
physics - The New Indian Model School, Dubai
... nurture the independence of the learner, given the fact that every learner is unique. The learner has to understand, appreciate, protect and build on values, beliefs and traditional wisdom, make the necessary modifications, improvisations and additions wherever and whenever necessary. The recent sci ...
... nurture the independence of the learner, given the fact that every learner is unique. The learner has to understand, appreciate, protect and build on values, beliefs and traditional wisdom, make the necessary modifications, improvisations and additions wherever and whenever necessary. The recent sci ...
Chapter 18: Problems
... parallel. (a) What is the resistance of the 50-W filament? (b) What is the resistance of the 100-W filament? (c) What is the equivalent resistance of the two filaments when they are in parallel? (d) What is the power dissipated when the switch is in position 3? 22. You have three identical resistors ...
... parallel. (a) What is the resistance of the 50-W filament? (b) What is the resistance of the 100-W filament? (c) What is the equivalent resistance of the two filaments when they are in parallel? (d) What is the power dissipated when the switch is in position 3? 22. You have three identical resistors ...
EC6201
... Objective: To acquaint the students with the construction, theory and operation power control devices, LED, LCD, and other Opto-electronic devices. ...
... Objective: To acquaint the students with the construction, theory and operation power control devices, LED, LCD, and other Opto-electronic devices. ...
TraceNet TCM2 Installation Guide
... Table 2.3: Maximum Heater Current Through Each Solid State Relay ...
... Table 2.3: Maximum Heater Current Through Each Solid State Relay ...
Excalibur Chip Set Controller
... and microcontroller interface. Its main function is to digitize the four unknown currents from the touchscreen corner nodes. The microcontroller establishes ASIC operating behavior at boot-up by writing internal registers used to control analog function and digital timing. It also establishes the op ...
... and microcontroller interface. Its main function is to digitize the four unknown currents from the touchscreen corner nodes. The microcontroller establishes ASIC operating behavior at boot-up by writing internal registers used to control analog function and digital timing. It also establishes the op ...
Integrated circuit
An integrated circuit or monolithic integrated circuit (also referred to as an IC, a chip, or a microchip) is a set of electronic circuits on one small plate (""chip"") of semiconductor material, normally silicon. This can be made much smaller than a discrete circuit made from independent electronic components. ICs can be made very compact, having up to several billion transistors and other electronic components in an area the size of a fingernail. The width of each conducting line in a circuit can be made smaller and smaller as the technology advances; in 2008 it dropped below 100 nanometers, and has now been reduced to tens of nanometers.ICs were made possible by experimental discoveries showing that semiconductor devices could perform the functions of vacuum tubes and by mid-20th-century technology advancements in semiconductor device fabrication. The integration of large numbers of tiny transistors into a small chip was an enormous improvement over the manual assembly of circuits using discrete electronic components. The integrated circuit's mass production capability, reliability and building-block approach to circuit design ensured the rapid adoption of standardized integrated circuits in place of designs using discrete transistors.ICs have two main advantages over discrete circuits: cost and performance. Cost is low because the chips, with all their components, are printed as a unit by photolithography rather than being constructed one transistor at a time. Furthermore, packaged ICs use much less material than discrete circuits. Performance is high because the IC's components switch quickly and consume little power (compared to their discrete counterparts) as a result of the small size and close proximity of the components. As of 2012, typical chip areas range from a few square millimeters to around 450 mm2, with up to 9 million transistors per mm2.Integrated circuits are used in virtually all electronic equipment today and have revolutionized the world of electronics. Computers, mobile phones, and other digital home appliances are now inextricable parts of the structure of modern societies, made possible by the low cost of integrated circuits.