![Flex](http://s1.studyres.com/store/data/008166818_1-e5a1e5517c876bb00621df2547622320-300x300.png)
Template For Examination Papers
... For this chip, and for an assumed working temperature of 25 °C, determine the following: a) The minimum voltage for a logic '1' output. b) The worst-case noise margin. c) Explain the term ‘propagation delay’ with reference to this integrated circuit (IC). What is the maximum propagation delay for th ...
... For this chip, and for an assumed working temperature of 25 °C, determine the following: a) The minimum voltage for a logic '1' output. b) The worst-case noise margin. c) Explain the term ‘propagation delay’ with reference to this integrated circuit (IC). What is the maximum propagation delay for th ...
EC8011 40V Gate Pulse Modulator - E-CMOS
... Gate pulse modulator (GPM) is controlled by frame signals from timing controller to modulate the Gate On voltage that acts a flicker compensation circuit to reduce the coupling effect between gate lines and pixels. The GPM is specially designed for the application of TFT LCD panel. It also can delay ...
... Gate pulse modulator (GPM) is controlled by frame signals from timing controller to modulate the Gate On voltage that acts a flicker compensation circuit to reduce the coupling effect between gate lines and pixels. The GPM is specially designed for the application of TFT LCD panel. It also can delay ...
TRANSPAK T752 ™ Potentiometer Input Isolating, Field
... 1. Open the access lid on the top of the unit (see Top View Diagram). 2. Select the output range using switch 1. The CLOSED position selects a 10-50mA output. The OPEN position selects a 4-20mA output. (Switches 2-6 are not used.) 3. Connect the input to a potentiometer. Connect the output loop to a ...
... 1. Open the access lid on the top of the unit (see Top View Diagram). 2. Select the output range using switch 1. The CLOSED position selects a 10-50mA output. The OPEN position selects a 4-20mA output. (Switches 2-6 are not used.) 3. Connect the input to a potentiometer. Connect the output loop to a ...
Basic Logic Gates
... below and test the output with a logic probe. Check the output using the logic probe you constructed in PART 1. ...
... below and test the output with a logic probe. Check the output using the logic probe you constructed in PART 1. ...
DM4003 POTENTIOMETER POSITION INPUT FIELD RANGEABLE
... it by hooking the top of the module’s latch onto the top of the rail, then use a downward rotating motion to snap the module onto the rail. To remove the module, insert a screwdriver into the slot on the spring loaded snap which is located on the lower backside of the unit. Apply a downward pressure ...
... it by hooking the top of the module’s latch onto the top of the rail, then use a downward rotating motion to snap the module onto the rail. To remove the module, insert a screwdriver into the slot on the spring loaded snap which is located on the lower backside of the unit. Apply a downward pressure ...
Transistor–transistor logic
![](https://commons.wikimedia.org/wiki/Special:FilePath/68k_ttl.jpg?width=300)
Transistor–transistor logic (TTL) is a class of digital circuits built from bipolar junction transistors (BJT) and resistors. It is called transistor–transistor logic because both the logic gating function (e.g., AND) and the amplifying function are performed by transistors (contrast with RTL and DTL).TTL is notable for being a widespread integrated circuit (IC) family used in many applications such as computers, industrial controls, test equipment and instrumentation, consumer electronics, synthesizers, etc. The designation TTL is sometimes used to mean TTL-compatible logic levels, even when not associated directly with TTL integrated circuits, for example as a label on the inputs and outputs of electronic instruments.After their introduction in integrated circuit form in 1963 by Sylvania, TTL integrated circuits were manufactured by several semiconductor companies, with the 7400 series (also called 74xx) by Texas Instruments becoming particularly popular. TTL manufacturers offered a wide range of logic gate, flip-flops, counters, and other circuits. Several variations from the original bipolar TTL concept were developed, giving circuits with higher speed or lower power dissipation to allow optimization of a design. TTL circuits simplified design of systems compared to earlier logic families, offering superior speed to resistor–transistor logic (RTL) and easier design layout than emitter-coupled logic (ECL). The design of the input and outputs of TTL gates allowed many elements to be interconnected.TTL became the foundation of computers and other digital electronics. Even after much larger scale integrated circuits made multiple-circuit-board processors obsolete, TTL devices still found extensive use as the ""glue"" logic interfacing more densely integrated components. TTL devices were originally made in ceramic and plastic dual-in-line (DIP) packages, and flat-pack form. TTL chips are now also made in surface-mount packages. Successors to the original bipolar TTL logic often are interchangeable in function with the original circuits, but with improved speed or lower power dissipation.