![MM74HC374 3-STATE Octal D-Type Flip-Flop](http://s1.studyres.com/store/data/002251658_1-0c1030a2cddea5f570f6f1ef5f4058ee-300x300.png)
Mechatronics I Laboratory Exercise 5
... noise at 60Hz. More sophisticated high order filters can be used to allow certain bands to pass or to create a more ideal filter. Op-amps are readily available as inexpensive integrated circuits (ICs). The opamp IC we have in the Mechtronics lab is the LM324 quad. This is a 14-pin DIP chip with four ...
... noise at 60Hz. More sophisticated high order filters can be used to allow certain bands to pass or to create a more ideal filter. Op-amps are readily available as inexpensive integrated circuits (ICs). The opamp IC we have in the Mechtronics lab is the LM324 quad. This is a 14-pin DIP chip with four ...
CN-0111
... in series with external divider resistors R3 and R4, as shown in Figure 2 and Figure 5, to create a vernier DAC with 10-bit resolution over a reduced VOUT range. This serves to increase the sensitivity of the DAC, similar to adding resistance in series with a potentiometer. In addition, the AD5292 h ...
... in series with external divider resistors R3 and R4, as shown in Figure 2 and Figure 5, to create a vernier DAC with 10-bit resolution over a reduced VOUT range. This serves to increase the sensitivity of the DAC, similar to adding resistance in series with a potentiometer. In addition, the AD5292 h ...
Measuring e/k
... breadboard to connect resistors, and measure their equivalent resistance. Apparatus: Breadboard, small connecting wires, 2-alligator clips, 2-resistors, and white DMM. Solder-less breadboards are important in electronics. They allow us to make quick circuits, test out ideas before making a more perm ...
... breadboard to connect resistors, and measure their equivalent resistance. Apparatus: Breadboard, small connecting wires, 2-alligator clips, 2-resistors, and white DMM. Solder-less breadboards are important in electronics. They allow us to make quick circuits, test out ideas before making a more perm ...
Skill Sheet 20.2 Network Circuits
... resistance is connected in parallel with another 2-ohm resistor. Thus the combined resistance of R3, R4, and R2 is 1 ohm. Now the circuit looks like: ...
... resistance is connected in parallel with another 2-ohm resistor. Thus the combined resistance of R3, R4, and R2 is 1 ohm. Now the circuit looks like: ...
BAŞKENT UNIVERSITY
... 4.1 What is the relation between Rg and RL ,which maximize the PL, in experiment 3.2 4.2 Where can you use the concept that you found in 4.1. ...
... 4.1 What is the relation between Rg and RL ,which maximize the PL, in experiment 3.2 4.2 Where can you use the concept that you found in 4.1. ...
Transistor–transistor logic
![](https://commons.wikimedia.org/wiki/Special:FilePath/68k_ttl.jpg?width=300)
Transistor–transistor logic (TTL) is a class of digital circuits built from bipolar junction transistors (BJT) and resistors. It is called transistor–transistor logic because both the logic gating function (e.g., AND) and the amplifying function are performed by transistors (contrast with RTL and DTL).TTL is notable for being a widespread integrated circuit (IC) family used in many applications such as computers, industrial controls, test equipment and instrumentation, consumer electronics, synthesizers, etc. The designation TTL is sometimes used to mean TTL-compatible logic levels, even when not associated directly with TTL integrated circuits, for example as a label on the inputs and outputs of electronic instruments.After their introduction in integrated circuit form in 1963 by Sylvania, TTL integrated circuits were manufactured by several semiconductor companies, with the 7400 series (also called 74xx) by Texas Instruments becoming particularly popular. TTL manufacturers offered a wide range of logic gate, flip-flops, counters, and other circuits. Several variations from the original bipolar TTL concept were developed, giving circuits with higher speed or lower power dissipation to allow optimization of a design. TTL circuits simplified design of systems compared to earlier logic families, offering superior speed to resistor–transistor logic (RTL) and easier design layout than emitter-coupled logic (ECL). The design of the input and outputs of TTL gates allowed many elements to be interconnected.TTL became the foundation of computers and other digital electronics. Even after much larger scale integrated circuits made multiple-circuit-board processors obsolete, TTL devices still found extensive use as the ""glue"" logic interfacing more densely integrated components. TTL devices were originally made in ceramic and plastic dual-in-line (DIP) packages, and flat-pack form. TTL chips are now also made in surface-mount packages. Successors to the original bipolar TTL logic often are interchangeable in function with the original circuits, but with improved speed or lower power dissipation.