![Free Datasheet Search Engine](http://s1.studyres.com/store/data/007889636_2-860c9fe7d241f3f2c64c1ab35d54c8d9-300x300.png)
Chapter 20 – Circuits and Circuit Elements
... Pg 732 for definition Does a lightbulb offer a complete conducting path? What are the components of a lightbulb? (a): charges enter at the base (b): go thru filament (c): exit at threads Series Circuits Resistors in series have the same current – all charges must flow through each resistor T ...
... Pg 732 for definition Does a lightbulb offer a complete conducting path? What are the components of a lightbulb? (a): charges enter at the base (b): go thru filament (c): exit at threads Series Circuits Resistors in series have the same current – all charges must flow through each resistor T ...
LM5100/LM5101 High Voltage High Side and Low Side Gate Driver
... configuration. The floating high-side driver is capable of operating with supply voltages up to 100V. The outputs are independently controlled with CMOS input thresholds (LM5100) or TTL input thresholds (LM5101). An integrated high voltage diode is provided to charge the high side gate drive bootstr ...
... configuration. The floating high-side driver is capable of operating with supply voltages up to 100V. The outputs are independently controlled with CMOS input thresholds (LM5100) or TTL input thresholds (LM5101). An integrated high voltage diode is provided to charge the high side gate drive bootstr ...
TD62M4600FG - Toshiba America Electronic Components
... exceed its absolute maximum ratings, when the wiring is routed improperly or when an abnormal pulse noise occurs from the wiring or load, causing a large current to continuously flow and the breakdown can lead smoke or ignition. To minimize the effects of the flow of a large current in case of break ...
... exceed its absolute maximum ratings, when the wiring is routed improperly or when an abnormal pulse noise occurs from the wiring or load, causing a large current to continuously flow and the breakdown can lead smoke or ignition. To minimize the effects of the flow of a large current in case of break ...
FSTD16861 20-Bit Bus Switch with Level Shifting FSTD16 861 20
... The Fairchild Switch FSTD16861 provides 20-bits of highspeed CMOS TTL-compatible bus switching. The low On Resistance of the switch allows inputs to be connected to outputs without adding propagation delay or generating additional ground bounce noise. A diode to VCC has been integrated into the circ ...
... The Fairchild Switch FSTD16861 provides 20-bits of highspeed CMOS TTL-compatible bus switching. The low On Resistance of the switch allows inputs to be connected to outputs without adding propagation delay or generating additional ground bounce noise. A diode to VCC has been integrated into the circ ...
SN54/74LS160A SN54/74LS161A SN54/74LS162A
... used to inhibit the count sequence. With the PE held HIGH, a LOW on either the CEP or CET inputs at least one set-up time prior to the LOW to HIGH clock transition will cause the existing output states to be retained. The AND feature of the two Count Enable inputs (CET • CEP) allows synchronous casc ...
... used to inhibit the count sequence. With the PE held HIGH, a LOW on either the CEP or CET inputs at least one set-up time prior to the LOW to HIGH clock transition will cause the existing output states to be retained. The AND feature of the two Count Enable inputs (CET • CEP) allows synchronous casc ...
3-Stage Transimpedance Amplifier
... In order to accomplish this, a shunt capacitor, Cshunt, was connected in parallel to the input of stage 3, bypassing some of the AC current to ground. An AC voltage divider had essentially been constructed for high frequencies. In order to determine the value of Cshunt, the resistance that this capa ...
... In order to accomplish this, a shunt capacitor, Cshunt, was connected in parallel to the input of stage 3, bypassing some of the AC current to ground. An AC voltage divider had essentially been constructed for high frequencies. In order to determine the value of Cshunt, the resistance that this capa ...
HAL 85x Programmable Hall-Effect Sensors with
... compensation, an A/D converter, digital signal processing, an open-drain output or output current source, an EEPROM memory with redundancy and lock function for the calibration data and the output characteristic, a serial interface for programming the EEPROM, and protection devices on all ...
... compensation, an A/D converter, digital signal processing, an open-drain output or output current source, an EEPROM memory with redundancy and lock function for the calibration data and the output characteristic, a serial interface for programming the EEPROM, and protection devices on all ...
Lab 4 - Ohm`s Law - Physics Introductory Labs at Stony Brook
... resistor as the device under test. Start at low voltage and slowly work your way up. Never exceed 10 Volts and 250 mA in this circuit. Space your voltage and current readings between 0 and these maxima. 2. Measure the current read by the ammeter for at least 5 values of voltage between 0 and 10 Volt ...
... resistor as the device under test. Start at low voltage and slowly work your way up. Never exceed 10 Volts and 250 mA in this circuit. Space your voltage and current readings between 0 and these maxima. 2. Measure the current read by the ammeter for at least 5 values of voltage between 0 and 10 Volt ...
Transistor–transistor logic
![](https://commons.wikimedia.org/wiki/Special:FilePath/68k_ttl.jpg?width=300)
Transistor–transistor logic (TTL) is a class of digital circuits built from bipolar junction transistors (BJT) and resistors. It is called transistor–transistor logic because both the logic gating function (e.g., AND) and the amplifying function are performed by transistors (contrast with RTL and DTL).TTL is notable for being a widespread integrated circuit (IC) family used in many applications such as computers, industrial controls, test equipment and instrumentation, consumer electronics, synthesizers, etc. The designation TTL is sometimes used to mean TTL-compatible logic levels, even when not associated directly with TTL integrated circuits, for example as a label on the inputs and outputs of electronic instruments.After their introduction in integrated circuit form in 1963 by Sylvania, TTL integrated circuits were manufactured by several semiconductor companies, with the 7400 series (also called 74xx) by Texas Instruments becoming particularly popular. TTL manufacturers offered a wide range of logic gate, flip-flops, counters, and other circuits. Several variations from the original bipolar TTL concept were developed, giving circuits with higher speed or lower power dissipation to allow optimization of a design. TTL circuits simplified design of systems compared to earlier logic families, offering superior speed to resistor–transistor logic (RTL) and easier design layout than emitter-coupled logic (ECL). The design of the input and outputs of TTL gates allowed many elements to be interconnected.TTL became the foundation of computers and other digital electronics. Even after much larger scale integrated circuits made multiple-circuit-board processors obsolete, TTL devices still found extensive use as the ""glue"" logic interfacing more densely integrated components. TTL devices were originally made in ceramic and plastic dual-in-line (DIP) packages, and flat-pack form. TTL chips are now also made in surface-mount packages. Successors to the original bipolar TTL logic often are interchangeable in function with the original circuits, but with improved speed or lower power dissipation.