Efficient Multi-domain ESD Analysis and
... flow, it can be used to study the non-uniform current flow through the fingers as shown in [7]. For CDM events, it is crucially important to make sure that the critical connections in the layout have adequate capacity to sustain the high currents and at the same time, low enough resistances to provi ...
... flow, it can be used to study the non-uniform current flow through the fingers as shown in [7]. For CDM events, it is crucially important to make sure that the critical connections in the layout have adequate capacity to sustain the high currents and at the same time, low enough resistances to provi ...
tFdU4101
... combined with the resistor R2 is the low pass filter for smoothing the supply voltage. R2, C1 and C2 are optional and dependent on the quality of the supply voltages VCC1 and injected noise. An unstable power supply with dropping voltage during transmission may reduce the sensitivity (and transmissi ...
... combined with the resistor R2 is the low pass filter for smoothing the supply voltage. R2, C1 and C2 are optional and dependent on the quality of the supply voltages VCC1 and injected noise. An unstable power supply with dropping voltage during transmission may reduce the sensitivity (and transmissi ...
Quad Channel, 16-Bit, Serial Input, Dynamic Power Control, HART Connectivity
... Changes to Readback Operation section and Table 26 .............. 38 Changes to Voltage Output Short-Circuit Protection Section .. 40 Changes to Figure 78 ...................................................................... 41 Changes to Figure 82 .................................................. ...
... Changes to Readback Operation section and Table 26 .............. 38 Changes to Voltage Output Short-Circuit Protection Section .. 40 Changes to Figure 78 ...................................................................... 41 Changes to Figure 82 .................................................. ...
ATS1000/2000/3000/4000 installation guide
... This publication may contain examples of screen captures and reports used in daily operations. Examples may include fictitious names of individuals and companies. Any similarity to names and addresses of actual businesses or persons is entirely coincidental. ...
... This publication may contain examples of screen captures and reports used in daily operations. Examples may include fictitious names of individuals and companies. Any similarity to names and addresses of actual businesses or persons is entirely coincidental. ...
Industrial and General-Purpose Gate Driver ICs
... ››Immunity against negative and positive transients ››Increases reliability of the end product ››Low losses and low power dissipation ...
... ››Immunity against negative and positive transients ››Increases reliability of the end product ››Low losses and low power dissipation ...
UBA20261/2 600 V and 350 V power IC for step dimmable CFLs
... state, the frequency sweeps down on the CI pin due to capacitor CCI charging at a fixed current as shown in Figure 4. During this continuous decrease in frequency, the circuit approaches the resonant frequency of the resonant tank (L2, C5). This action causes a high voltage across the lamp to ignite ...
... state, the frequency sweeps down on the CI pin due to capacitor CCI charging at a fixed current as shown in Figure 4. During this continuous decrease in frequency, the circuit approaches the resonant frequency of the resonant tank (L2, C5). This action causes a high voltage across the lamp to ignite ...
35 Electric Circuits
... To prevent overloading in circuits, fuses or circuit breakers are connected in series along the supply line. That means, the entire line current must pass through the fuse. ...
... To prevent overloading in circuits, fuses or circuit breakers are connected in series along the supply line. That means, the entire line current must pass through the fuse. ...
Cold-Junction Compensated Thermocouple-to-Digital Converter General Description Features
... updated when CS is high. Drive CS low to output the first bit on the SO pin. A complete serial-interface read of the cold-junction compensated thermocouple temperature requires 14 clock cycles. Thirty-two clock cycles are required to read both the thermocouple and reference junction temperatures (Ta ...
... updated when CS is high. Drive CS low to output the first bit on the SO pin. A complete serial-interface read of the cold-junction compensated thermocouple temperature requires 14 clock cycles. Thirty-two clock cycles are required to read both the thermocouple and reference junction temperatures (Ta ...
ST7LNB1Y0
... 2. The divider chain connected to the DRX1 pins must have the following resistance values: 330 KΩ and 100 KΩ. 3. Unused I2C lines (SCL2,SDA2) have to be linked to VCC through 12 KΩ resistors. 4. RTA-STB: Remote Tuning Able Set Top Box (STB supporting SaTCR control). 5. The transistor is optional, it ...
... 2. The divider chain connected to the DRX1 pins must have the following resistance values: 330 KΩ and 100 KΩ. 3. Unused I2C lines (SCL2,SDA2) have to be linked to VCC through 12 KΩ resistors. 4. RTA-STB: Remote Tuning Able Set Top Box (STB supporting SaTCR control). 5. The transistor is optional, it ...
Data Sheets - Leadtrend Technology
... Stress exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stress above Recommended Operating Conditions may affect device reliability. ...
... Stress exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stress above Recommended Operating Conditions may affect device reliability. ...
Valve RF amplifier
A valve RF amplifier (UK and Aus.) or tube amplifier (U.S.), is a device for electrically amplifying the power of an electrical radio frequency signal.Low to medium power valve amplifiers for frequencies below the microwaves were largely replaced by solid state amplifiers during the 1960s and 1970s, initially for receivers and low power stages of transmitters, transmitter output stages switching to transistors somewhat later. Specially constructed valves are still in use for very high power transmitters, although rarely in new designs.