XHRA-2HPA Datasheet
... · Audio master clock for the asynchronous clocking mode. (MCLK) If the master clock is fixed at 24.576 MHz, then only 48, 96, 192, and 384 KHz can be supported; and the other frequencies should be disabled in the configuration (byte 6, Appendix A.2). If the master clock is fixed at 22.5792 MHz, then ...
... · Audio master clock for the asynchronous clocking mode. (MCLK) If the master clock is fixed at 24.576 MHz, then only 48, 96, 192, and 384 KHz can be supported; and the other frequencies should be disabled in the configuration (byte 6, Appendix A.2). If the master clock is fixed at 22.5792 MHz, then ...
lec5
... For the parallel connection of elements, KVL requires that all the voltages across the elements be the same, and KCL requires that the currents through the parallel connection be the sum of the currents in all the brunches. For nonlinear voltage-controlled resistors, the equivalent resistor of the p ...
... For the parallel connection of elements, KVL requires that all the voltages across the elements be the same, and KCL requires that the currents through the parallel connection be the sum of the currents in all the brunches. For nonlinear voltage-controlled resistors, the equivalent resistor of the p ...
User Manual
... The microK 100 and microK 200 thermometry bridges use a completely new ADC (analogue-to-digital converter) and low noise amplifier technology (see section 7: “The microK Technology”) to provide levels of performance previously only available using AC resistance bridges. Uniquely, the microK bridges ...
... The microK 100 and microK 200 thermometry bridges use a completely new ADC (analogue-to-digital converter) and low noise amplifier technology (see section 7: “The microK Technology”) to provide levels of performance previously only available using AC resistance bridges. Uniquely, the microK bridges ...
ATM-414 – Pneumatic systems Electro
... are included in the same switch block with pushbutton switches, as shown in Fig. 1.6.c ...
... are included in the same switch block with pushbutton switches, as shown in Fig. 1.6.c ...
Power System II
... From the Derived equation is clear that to simulate a L-G fault all the three sequence networks are required and since the currents are equal in magnitude And phase angle, therefore, the three sequence networks must be connected in 5 min Series. Questions / Answers Q1. What are the shunts faults? A1 ...
... From the Derived equation is clear that to simulate a L-G fault all the three sequence networks are required and since the currents are equal in magnitude And phase angle, therefore, the three sequence networks must be connected in 5 min Series. Questions / Answers Q1. What are the shunts faults? A1 ...
AD5625R/AD5645R/AD5665R, AD5625/AD5665
... full-scale output range of 2.5 V; the AD56x5RBRUZ (TSSOP) have a 2.5 V, 5 ppm/°C reference giving a full-scale output range of 5 V. The on-chip reference is off at power-up, allowing the use of an external reference. The internal reference is enabled via a software write. The AD5665/AD5625 require a ...
... full-scale output range of 2.5 V; the AD56x5RBRUZ (TSSOP) have a 2.5 V, 5 ppm/°C reference giving a full-scale output range of 5 V. The on-chip reference is off at power-up, allowing the use of an external reference. The internal reference is enabled via a software write. The AD5665/AD5625 require a ...
Reactive Power Compensation
... Mostly for detunned filtering, in order to prevent resonance issues. Small tunned filters can also be used, mostly with filter buliding blocks (reactors and resistors) installed separated and not in the enclosure. Can be used for tunned filters with filter buliding blocks (reactors and resistors) in ...
... Mostly for detunned filtering, in order to prevent resonance issues. Small tunned filters can also be used, mostly with filter buliding blocks (reactors and resistors) installed separated and not in the enclosure. Can be used for tunned filters with filter buliding blocks (reactors and resistors) in ...
PCF1179CT
... A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. ...
... A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. ...
M1000C RS232 Configuration Programmer’s Manual Revision: 22.08.2007
... Plug one end of the supplied RS232 cable into the grey RJ plug located on the side of the M1000C (next to the supply). The other end of the cable (with the DB9 plug) connects to a PC COM port (COM1 is used in this manual). Important: Do not attach the power supply to the M1000 before the Microsoft® ...
... Plug one end of the supplied RS232 cable into the grey RJ plug located on the side of the M1000C (next to the supply). The other end of the cable (with the DB9 plug) connects to a PC COM port (COM1 is used in this manual). Important: Do not attach the power supply to the M1000 before the Microsoft® ...
MAX34408/MAX34409 SMBus Dual/Quad Current Monitor General Description Features
... hardware output to provide an immediate indication to shut down any necessary external circuitry. The devices provide an ALERT output signal. Host communications are conducted through a SMBus-compatible communications port. ...
... hardware output to provide an immediate indication to shut down any necessary external circuitry. The devices provide an ALERT output signal. Host communications are conducted through a SMBus-compatible communications port. ...
Valve RF amplifier
A valve RF amplifier (UK and Aus.) or tube amplifier (U.S.), is a device for electrically amplifying the power of an electrical radio frequency signal.Low to medium power valve amplifiers for frequencies below the microwaves were largely replaced by solid state amplifiers during the 1960s and 1970s, initially for receivers and low power stages of transmitters, transmitter output stages switching to transistors somewhat later. Specially constructed valves are still in use for very high power transmitters, although rarely in new designs.