Non-inverting amplifier
... Limit of the rate at which the output can change Typical values : a few V/ms A sine wave of amplitude A and frequency f requires a slew rate of 2pAf S (V/ms) = 0.3 fT (MHz); fT = frequency at which gain = 1 ...
... Limit of the rate at which the output can change Typical values : a few V/ms A sine wave of amplitude A and frequency f requires a slew rate of 2pAf S (V/ms) = 0.3 fT (MHz); fT = frequency at which gain = 1 ...
5V, 10-Bit, 400 KSPS, 4/8 Channel, Low Power
... digital inputs and a 3-state output [chip select (CS), serial input-output clock (SCLK), serial data input (SDI), and serial data output (SDO)] that provide a direct 4-wire interface to the serial port of most popular host microprocessors (SPI interface). When interfaced with a DSP, a frame sync (FS ...
... digital inputs and a 3-state output [chip select (CS), serial input-output clock (SCLK), serial data input (SDI), and serial data output (SDO)] that provide a direct 4-wire interface to the serial port of most popular host microprocessors (SPI interface). When interfaced with a DSP, a frame sync (FS ...
MAX1471 315MHz/434MHz Low-Power, 3V/5V ASK/FSK Superheterodyne Receiver General Description
... The MAX1471 low-power, CMOS, superheterodyne, RF dual-channel receiver is designed to receive both amplitude-shift-keyed (ASK) and frequency-shift-keyed (FSK) data without reconfiguring the device or introducing any time delay normally associated with changing modulation schemes. The MAX1471 require ...
... The MAX1471 low-power, CMOS, superheterodyne, RF dual-channel receiver is designed to receive both amplitude-shift-keyed (ASK) and frequency-shift-keyed (FSK) data without reconfiguring the device or introducing any time delay normally associated with changing modulation schemes. The MAX1471 require ...
AD5405 AnaDev, dual I-dac, 58MSPS R2R, no ref.pdf
... The AD54051 is a dual CMOS, 12-bit, current output digitalto-analog converter (DAC).This device operates from a 2.5 V to 5.5 V power supply, making it suited to battery-powered and other applications. The applied external reference input voltage (VREF) determines the full-scale output current. An in ...
... The AD54051 is a dual CMOS, 12-bit, current output digitalto-analog converter (DAC).This device operates from a 2.5 V to 5.5 V power supply, making it suited to battery-powered and other applications. The applied external reference input voltage (VREF) determines the full-scale output current. An in ...
Technote 7 Using Op Amps Successfully
... have a ground terminal. Ground is implied. This is easy to ignore. After all, most amplifiers, at least the older ones, operate from ±15 V or ±12 V rails and are biased symmetrically above and below ground. “Ground” is than half way between the rails and everything works as long as your signals rema ...
... have a ground terminal. Ground is implied. This is easy to ignore. After all, most amplifiers, at least the older ones, operate from ±15 V or ±12 V rails and are biased symmetrically above and below ground. “Ground” is than half way between the rails and everything works as long as your signals rema ...
MAX12559 Dual, 96Msps, 14-Bit, IF/Baseband ADC General Description Features
... The MAX12559 is a dual, 3.3V, 14-bit analog-to-digital converter (ADC) featuring fully differential wideband track-and-hold (T/H) inputs, driving internal quantizers. The MAX12559 is optimized for low power, small size, and high dynamic performance in intermediate frequency (IF) and baseband samplin ...
... The MAX12559 is a dual, 3.3V, 14-bit analog-to-digital converter (ADC) featuring fully differential wideband track-and-hold (T/H) inputs, driving internal quantizers. The MAX12559 is optimized for low power, small size, and high dynamic performance in intermediate frequency (IF) and baseband samplin ...
BASIC ELECTRICITY
... This text is set up differently from most subcourses It is a workbook that utilizes programmed instruction. The numbered "frames" present information and/or a question about presented information. You should work through the frames in the order presented. Answer each question that is presented. To c ...
... This text is set up differently from most subcourses It is a workbook that utilizes programmed instruction. The numbered "frames" present information and/or a question about presented information. You should work through the frames in the order presented. Answer each question that is presented. To c ...
EG12000 - Medlab GmbH
... The number of wires attached to the patient, to his arms, legs and chest. Normally, the term "lead" is also often used for channels, which is not fully correct. It is, for example, possible to measure 12 channels with 10 leads, but only one channel can be measured with three leads attached. Channels ...
... The number of wires attached to the patient, to his arms, legs and chest. Normally, the term "lead" is also often used for channels, which is not fully correct. It is, for example, possible to measure 12 channels with 10 leads, but only one channel can be measured with three leads attached. Channels ...
