• Study Resource
  • Explore
    • Arts & Humanities
    • Business
    • Engineering & Technology
    • Foreign Language
    • History
    • Math
    • Science
    • Social Science

    Top subcategories

    • Advanced Math
    • Algebra
    • Basic Math
    • Calculus
    • Geometry
    • Linear Algebra
    • Pre-Algebra
    • Pre-Calculus
    • Statistics And Probability
    • Trigonometry
    • other →

    Top subcategories

    • Astronomy
    • Astrophysics
    • Biology
    • Chemistry
    • Earth Science
    • Environmental Science
    • Health Science
    • Physics
    • other →

    Top subcategories

    • Anthropology
    • Law
    • Political Science
    • Psychology
    • Sociology
    • other →

    Top subcategories

    • Accounting
    • Economics
    • Finance
    • Management
    • other →

    Top subcategories

    • Aerospace Engineering
    • Bioengineering
    • Chemical Engineering
    • Civil Engineering
    • Computer Science
    • Electrical Engineering
    • Industrial Engineering
    • Mechanical Engineering
    • Web Design
    • other →

    Top subcategories

    • Architecture
    • Communications
    • English
    • Gender Studies
    • Music
    • Performing Arts
    • Philosophy
    • Religious Studies
    • Writing
    • other →

    Top subcategories

    • Ancient History
    • European History
    • US History
    • World History
    • other →

    Top subcategories

    • Croatian
    • Czech
    • Finnish
    • Greek
    • Hindi
    • Japanese
    • Korean
    • Persian
    • Swedish
    • Turkish
    • other →
 
Profile Documents Logout
Upload
PTC-NTC for Surface Mounting Application
PTC-NTC for Surface Mounting Application

Datasheet - Texas Instruments
Datasheet - Texas Instruments

d - eomac00a04-10en
d - eomac00a04-10en

... Static sensitive components. A static discharge while handling electronic circuit boards can cause damage to the components. Discharge any static electrical charge by touching the bare metal inside the control panel before performing any service work. Never unplug any cables, circuit board terminal ...
Energy and Forces Mark Scheme - crypt
Energy and Forces Mark Scheme - crypt

Pressure Detectors - Nuclear Community
Pressure Detectors - Nuclear Community

Bates
Bates

NAVSEA TE000-AB-GTP-010 Rev 1 With Change A Parts Derating
NAVSEA TE000-AB-GTP-010 Rev 1 With Change A Parts Derating

... Standard resistors are specified in MIL-STD-199. MIL-STD-199 is the key overall standard for resistor selection; although this standard addresses only selected standard resistors, it should be used to the greatest extent possible. It presents detailed data for use in the design of military equipment ...
CO2/T/.. Series Sensors Data Sheet
CO2/T/.. Series Sensors Data Sheet

Model 330 - Lake Shore Cryotronics, Inc.
Model 330 - Lake Shore Cryotronics, Inc.

Resistors
Resistors

Bates
Bates

... can short out internally. They may, however, become short-circuited by another component in the circuit. ...
AD5227 64-Position Up/Down Control Digital Potentiometer Data
AD5227 64-Position Up/Down Control Digital Potentiometer Data

AS Electricity Part II
AS Electricity Part II

General Description Features
General Description Features

... while reducing noise. Switching speeds of internal MOSFETs are optimized to reduce noise and EMI. An ultralow-drift chopper amplifier maintains ±0.001°C temperature stability. Output current, rather than voltage, is directly controlled to eliminate current surges. Individual heating and cooling curr ...
LOW VOLTAGE TEMPERATURE SENSOR DESIGN FOR ON-CHIP THERMAL MANAGEMENT  by
LOW VOLTAGE TEMPERATURE SENSOR DESIGN FOR ON-CHIP THERMAL MANAGEMENT by

... criterion. Temperature sensors with low and process scalable supply voltages are proposed in this dissertation. Specifically, subthrehsold MOSFET diodes are used as sensing devices. Compared with traditional bipolar junction transistor (BJT) diodes, MOSFETs working in subthreshold region exhibit sim ...
103_unit_2
103_unit_2

2 marks - crypt
2 marks - crypt

... a) i) Lamp A is marked 3V, 0.25A. What does this tell you? The P.D. across a lamp in series with another lamp depends on the resistance of the 2 lamps. The voltage across each will be in the ratio of the resistances. The (2 marks) marking on the lamp tells you what voltage it was designed to be oper ...
TSI THERMAL ANEMOMETRY PROBES
TSI THERMAL ANEMOMETRY PROBES

MAX31730 3-Channel Remote Temperature Sensor General Description Features and Benefits
MAX31730 3-Channel Remote Temperature Sensor General Description Features and Benefits

... the target register. To write multiple bytes to two or more contiguous registers, write a new byte after each ACK. The register address then increments after each byte is written. End the transaction with a STOP condition. The read-byte format consists of the master transmitting the slave address fo ...
Fundamentals of Thermodynamics 8e
Fundamentals of Thermodynamics 8e

chapter 3—electricity
chapter 3—electricity

MAX31730 3-Channel Remote Temperature Sensor
MAX31730 3-Channel Remote Temperature Sensor

... the target register. To write multiple bytes to two or more contiguous registers, write a new byte after each ACK. The register address then increments after each byte is written. End the transaction with a STOP condition. The read-byte format consists of the master transmitting the slave address fo ...
The Electrical, Thermal and Spatial Integration of a Converter in a
The Electrical, Thermal and Spatial Integration of a Converter in a

Thermal Sensors Product Range Guide
Thermal Sensors Product Range Guide

Dielectric Study of Triton X100: a Glass- forming liquid
Dielectric Study of Triton X100: a Glass- forming liquid

... carried at different rates (see legend) and b) during the heating run, followed immediately after the cooling, which was performed always at the same rate (9 K·min-1) (same colours and symbols apply). The inset presents the corresponding isochronal loss trace, ´´, obtained during heating evidencing ...
< 1 2 3 4 5 6 7 8 9 ... 194 >

Lumped element model



The lumped element model (also called lumped parameter model, or lumped component model) simplifies the description of the behaviour of spatially distributed physical systems into a topology consisting of discrete entities that approximate the behaviour of the distributed system under certain assumptions. It is useful in electrical systems (including electronics), mechanical multibody systems, heat transfer, acoustics, etc.Mathematically speaking, the simplification reduces the state space of the system to a finite dimension, and the partial differential equations (PDEs) of the continuous (infinite-dimensional) time and space model of the physical system into ordinary differential equations (ODEs) with a finite number of parameters.
  • studyres.com © 2025
  • DMCA
  • Privacy
  • Terms
  • Report